ramips: add support for TP-Link MR600 V2(EU)
MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.
- Specifications:
* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
Signal3
- MAC Addresses:
OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN
- Installation:
1. Download the OpenWrt initramfs-image.
Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.
3. Connect to the serial console.
Attach power and interrupt the boot procedure when prompted (type `tpl`).
Credentials are admin / 1234
4. Configure U-Boot for booting OpenWrt from ram
$ tftpboot
$ bootm
5. Transfer the OpenWrt sysupgrade image to the device.
- LTE:
In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
option device '/dev/cdc-wdm0'
option proto 'qmi'
option pincode 'XXXX'
option apn 'your_isp_apn'
```
2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`
Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
This commit is contained in:
Linos Giannopoulos
Hauke Mehrtens
parent
f7f9203854
commit
78110c3b5f
|
|
@ -0,0 +1,207 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "tplink,mr600-v2-eu", "mediatek,mt7621-soc";
|
||||
model = "TP-Link MR600 v2 (EU)";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wlan {
|
||||
label = "wlan";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WLAN>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "white:power";
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
wlan {
|
||||
label = "white:wlan";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
wan {
|
||||
label = "white:wan";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal1 {
|
||||
label = "white:signal1";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal2 {
|
||||
label = "white:signal2";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal3 {
|
||||
label = "white:signal3";
|
||||
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
4g {
|
||||
label = "white:4g";
|
||||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
lan {
|
||||
label = "white:lan";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <80000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "uboot";
|
||||
reg = <0x00000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "openwrt,uimage";
|
||||
openwrt,offset = <512>; /* account for the 512-byte long header */
|
||||
label = "firmware";
|
||||
reg = <0x20000 0xfa0000>;
|
||||
};
|
||||
|
||||
romfile: partition@fc0000 {
|
||||
label = "romfile";
|
||||
reg = <0xfc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fd0000 {
|
||||
label = "config";
|
||||
reg = <0xfd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
radio: partition@fe0000 {
|
||||
label = "radio";
|
||||
reg = <0xfe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
|
||||
&pcie0 {
|
||||
mt76@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&macaddr_romfile_f100>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
mediatek,mtd-eeprom = <&radio 0x0>;
|
||||
mtd-mac-address = <&romfile 0xf100>;
|
||||
ieee80211-freq-limit = <2400000 2500000>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
mt76@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&radio 0x8000>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
nvmem-cells = <&macaddr_romfile_f100>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
mac-address-increment = <(-1)>;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
nvmem-cells = <&macaddr_romfile_f100>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
label = "wan";
|
||||
phy-handle = <ðphy4>;
|
||||
|
||||
nvmem-cells = <&macaddr_romfile_f100>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
ethphy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@1 {
|
||||
status = "okay";
|
||||
label = "lan1";
|
||||
};
|
||||
port@2 {
|
||||
status = "okay";
|
||||
label = "lan2";
|
||||
};
|
||||
port@3 {
|
||||
status = "okay";
|
||||
label = "lan3";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&romfile {
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_romfile_f100: romfile@f100 {
|
||||
reg = <0xf100 0x6>;
|
||||
};
|
||||
};
|
||||
|
|
@ -1910,6 +1910,21 @@ define Device/tplink_eap615-wall-v1
|
|||
endef
|
||||
TARGET_DEVICES += tplink_eap615-wall-v1
|
||||
|
||||
define Device/tplink_mr600-v2-eu
|
||||
$(Device/dsa-migration)
|
||||
$(Device/tplink-v2)
|
||||
DEVICE_MODEL := MR600
|
||||
DEVICE_VARIANT := v2 (EU)
|
||||
TPLINK_FLASHLAYOUT := 16Mltq
|
||||
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
||||
kmod-usb-net-qmi-wwan uqmi kmod-usb3
|
||||
KERNEL := $(KERNEL_DTB) | uImage lzma
|
||||
KERNEL_INITRAMFS := $$(KERNEL) | tplink-v2-header
|
||||
TPLINK_BOARD_ID := MR600-V2-EU
|
||||
IMAGE_SIZE := 16384k
|
||||
endef
|
||||
TARGET_DEVICES += tplink_mr600-v2-eu
|
||||
|
||||
define Device/tplink_re350-v1
|
||||
$(Device/dsa-migration)
|
||||
$(Device/tplink-safeloader)
|
||||
|
|
|
|||
|
|
@ -147,6 +147,11 @@ tplink,re350-v1)
|
|||
ucidef_set_led_netdev "eth_act" "LAN act" "green:eth_act" "lan" "tx rx"
|
||||
ucidef_set_led_netdev "eth_link" "LAN link" "green:eth_link" "lan" "link"
|
||||
;;
|
||||
tplink,mr600-v2-eu)
|
||||
ucidef_set_led_netdev "lan" "LAN" "white:lan" "br-lan"
|
||||
ucidef_set_led_netdev "wan" "WAN" "white:wan" "wan"
|
||||
ucidef_set_led_netdev "4g" "4G" "white:4g" "wwan0"
|
||||
;;
|
||||
tplink,re500-v1|\
|
||||
tplink,re650-v1|\
|
||||
tplink,re650-v2)
|
||||
|
|
|
|||
|
|
@ -100,6 +100,9 @@ ramips_setup_interfaces()
|
|||
tplink,tl-wpa8631p-v3)
|
||||
ucidef_set_interface_lan "lan1 lan2 lan3 plc0"
|
||||
;;
|
||||
tplink,mr600-v2-eu)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
||||
;;
|
||||
ubnt,edgerouter-x)
|
||||
ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4" "eth0"
|
||||
;;
|
||||
|
|
@ -216,6 +219,11 @@ ramips_setup_macs()
|
|||
wan_mac=$(mtd_get_mac_ascii Config wan_hwaddr)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
tplink,mr600-v2-eu)
|
||||
label_mac=$(cat "/sys/class/net/eth0/address")
|
||||
wwan_mac=$(macaddr_add $label_mac 1)
|
||||
ucidef_set_interface "wwan0" device "/dev/cdc-wdm0" protocol "qmi" macaddr "$wwan_mac"
|
||||
;;
|
||||
mikrotik,routerboard-750gr3|\
|
||||
mikrotik,routerboard-760igs|\
|
||||
mikrotik,routerboard-m11g|\
|
||||
|
|
|
|||
Loading…
Reference in New Issue