ipq40xx: add Edgecore ECW5211 support

This patch adds support for the Edgecore ECW5211 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This commit is contained in:
Robert Marko 2020-09-07 12:50:45 +02:00 committed by John Crispin
parent 59f0a0fd83
commit 4488b260a0
10 changed files with 351 additions and 3 deletions

View File

@ -32,6 +32,7 @@ ubootenv_mtdinfo () {
case "$board" in
alfa-network,ap120c-ac |\
edgecore,ecw5211 |\
glinet,gl-b1300 |\
openmesh,a42 |\
openmesh,a62)

View File

@ -31,6 +31,7 @@ ALLWIFIBOARDS:= \
buffalo_wtr-m2133hp \
cellc_rtl30vw \
dlink_dap2610 \
edgecore_ecw5211 \
edgecore_ecw5410 \
engenius_eap2200 \
engenius_emd1 \
@ -106,6 +107,7 @@ $(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater
$(eval $(call generate-ipq-wifi-package,buffalo_wtr-m2133hp,Buffalo WTR-M2133HP))
$(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5211,Edgecore ECW5211))
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))

View File

@ -62,6 +62,7 @@ zyxel,nbg6617)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt"
;;
edgecore,ecw5211 |\
zyxel,wre6606)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy1tpt"

View File

@ -38,6 +38,7 @@ ipq40xx_setup_interfaces()
;;
asus,map-ac2200|\
cilab,meshpoint-one|\
edgecore,ecw5211|\
openmesh,a42|\
openmesh,a62)
ucidef_set_interfaces_lan_wan "eth1" "eth0"

View File

@ -93,6 +93,7 @@ case "$FIRMWARE" in
cellc,rtl30vw |\
compex,wpj419 |\
compex,wpj428 |\
edgecore,ecw5211 |\
engenius,eap1300 |\
engenius,eap2200 |\
openmesh,a42 |\
@ -186,6 +187,7 @@ case "$FIRMWARE" in
cellc,rtl30vw |\
compex,wpj419 |\
compex,wpj428 |\
edgecore,ecw5211 |\
engenius,eap1300 |\
engenius,eap2200 |\
openmesh,a42 |\

View File

@ -66,6 +66,7 @@ platform_do_upgrade() {
avm,fritzrepeater-3000 |\
buffalo,wtr-m2133hp |\
cilab,meshpoint-one |\
edgecore,ecw5211 |\
engenius,eap2200 |\
mobipromo,cm520-79f |\
qxwlan,e2600ac-c2)

View File

@ -0,0 +1,325 @@
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "Edgecore ECW5211";
compatible = "edgecore,ecw5211";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
chosen {
bootargs-append = " root=/dev/ubiblock0_1";
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "ecw5211:yellow:power";
gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
};
wlan2g {
label = "ecw5211:green:wlan2g";
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
};
wlan5g {
label = "ecw5211:green:wlan5g";
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
};
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
};
ess-psgmii@98000 {
status = "okay";
};
counter@4a1000 {
compatible = "qcom,qca-gcnt";
reg = <0x4a1000 0x4>;
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@194b000 {
status = "okay";
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
usb2: usb2@60f8800 {
status = "okay";
};
usb3: usb3@8af8800 {
status = "okay";
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
};
edma@c080000 {
status = "okay";
};
};
};
&tlmm {
mdio_pins: mdio_pinmux {
mux_mdio {
pins = "gpio53";
function = "mdio";
bias-pull-up;
};
mux_mdc {
pins = "gpio52";
function = "mdc";
bias-pull-up;
};
};
serial_pins: serial_pinmux {
mux {
pins = "gpio60", "gpio61";
function = "blsp_uart0";
bias-disable;
};
};
spi0_pins: spi0_pinmux {
pin {
function = "blsp_spi0";
pins = "gpio55", "gpio56", "gpio57";
drive-strength = <2>;
bias-disable;
};
pin_cs {
function = "gpio";
pins = "gpio54", "gpio4";
drive-strength = <2>;
bias-disable;
output-high;
};
};
i2c0_pins: i2c0_pinmux {
mux_i2c {
function = "blsp_i2c0";
pins = "gpio58", "gpio59";
drive-strength = <16>;
bias-disable;
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_spi1 {
status = "okay";
pinctrl-0 = <&spi0_pins>;
pinctrl-names = "default";
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>;
flash@0 {
status = "okay";
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "0:SBL1";
reg = <0x00000000 0x00040000>;
read-only;
};
partition@40000 {
label = "0:MIBIB";
reg = <0x00040000 0x00020000>;
read-only;
};
partition@60000 {
label = "0:QSEE";
reg = <0x00060000 0x00060000>;
read-only;
};
partition@c0000 {
label = "0:CDT";
reg = <0x000c0000 0x00010000>;
read-only;
};
partition@d0000 {
label = "0:DDRPARAMS";
reg = <0x000d0000 0x00010000>;
read-only;
};
partition@e0000 {
label = "0:APPSBLENV"; /* uboot env*/
reg = <0x000e0000 0x00010000>;
read-only;
};
partition@f0000 {
label = "0:APPSBL"; /* uboot */
reg = <0x000f0000 0x00080000>;
read-only;
};
partition@170000 {
label = "0:ART";
reg = <0x00170000 0x00010000>;
read-only;
};
};
};
spi-nand@1 {
status = "okay";
compatible = "spi-nand";
reg = <1>;
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "rootfs";
reg = <0x00000000 0x04000000>;
};
};
};
};
&blsp1_i2c3 {
status = "okay";
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "default";
tpm@29 {
compatible = "atmel,at97sc3204t";
reg = <0x29>;
};
};
&blsp1_uart1 {
status = "okay";
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
};
&cryptobam {
status = "okay";
};
&gmac0 {
qcom,poll_required = <1>;
qcom,poll_required_dynamic = <1>;
qcom,phy_mdio_addr = <4>;
vlan_tag = <2 0x20>;
};
&gmac1 {
qcom,poll_required = <1>;
qcom,poll_required_dynamic = <1>;
qcom,phy_mdio_addr = <3>;
vlan_tag = <1 0x10>;
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "Edgecore-ECW5211";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "Edgecore-ECW5211";
};
&usb3_ss_phy {
status = "okay";
};
&usb3_hs_phy {
status = "okay";
};
&usb2_hs_phy {
status = "okay";
};

View File

@ -344,6 +344,18 @@ define Device/dlink_dap-2610
endef
TARGET_DEVICES += dlink_dap-2610
define Device/edgecore_ecw5211
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_TITLE := Edgecore ECW5211
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
DEVICE_DTS := qcom-ipq4018-ecw5211
DEVICE_PACKAGES := ipq-wifi-edgecore_ecw5211 kmod-tpm-i2c-atmel kmod-usb-acm uboot-envtools
endef
TARGET_DEVICES += edgecore_ecw5211
define Device/engenius_eap1300
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius

View File

@ -8,9 +8,11 @@ Signed-off-by: John Crispin <john@phrozen.org>
arch/arm/boot/dts/Makefile | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -837,11 +837,50 @@ dtb-$(CONFIG_ARCH_QCOM) += \
Index: linux-5.4.63/arch/arm/boot/dts/Makefile
===================================================================
--- linux-5.4.63.orig/arch/arm/boot/dts/Makefile
+++ linux-5.4.63/arch/arm/boot/dts/Makefile
@@ -837,11 +837,51 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@ -20,6 +22,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
+ qcom-ipq4018-ea6350v3.dtb \
+ qcom-ipq4018-eap1300.dtb \
+ qcom-ipq4018-ecw5211.dtb \
+ qcom-ipq4018-emd1.dtb \
+ qcom-ipq4018-emr3500.dtb \
+ qcom-ipq4018-ens620ext.dtb \