realtek: Add support for ZyXEL GS1900-48 Switch
The GS1900-48 is a 48 + 2 port Gigabit L2 switch with 48 gigabit ports.
Hardware:
RTL8393M SoC
Macronix MX25l12805D (16MB flash)
128MB RAM
6 * RTL8218B external PHY
2 * RTL8231 GPIO extenders to control the port LEDs, system LED and
Reset button
2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules.
Power is supplied via a 230 volt mains connector.
The board has a hard reset switch SW1, which is is not reachable from the outside.
J4 provides a 12V RS232 serial connector which is connected through U8 to
the 3.3V UART of the RTL8393. Conversion is done by U8, a SIPEX 3232EC.
To connect to the UART, wires can be soldered to R603 (TX) and R602 (RX).
Installation:
Install the squashfs image via Realtek's original Web-Interface.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This commit is contained in:
Birger Koblitz
Daniel Golle
parent
0a7565e536
commit
47f5a0a3ee
|
|
@ -7,7 +7,7 @@ BOARD:=realtek
|
|||
BOARDNAME:=Realtek MIPS
|
||||
DEVICE_TYPE:=basic
|
||||
FEATURES:=ramdisk squashfs
|
||||
SUBTARGETS:=rtl838x
|
||||
SUBTARGETS:=rtl838x rtl839x
|
||||
|
||||
KERNEL_PATCHVER:=5.10
|
||||
|
||||
|
|
|
|||
326
target/linux/realtek/dts-5.10/rtl8393_zyxel_gs1900-48.dts
Normal file
326
target/linux/realtek/dts-5.10/rtl8393_zyxel_gs1900-48.dts
Normal file
|
|
@ -0,0 +1,326 @@
|
|||
/dts-v1/;
|
||||
|
||||
#include "rtl839x.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
/ {
|
||||
compatible = "zyxel,gs1900-48", "realtek,rtl8393-soc";
|
||||
model = "Zyxel GS1900-48";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_sys;
|
||||
led-failsafe = &led_sys;
|
||||
led-running = &led_sys;
|
||||
led-upgrade = &led_sys;
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x8000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
leds {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinmux_disable_sys_led>;
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_sys: sys {
|
||||
label = "green:sys";
|
||||
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio1: rtl8231-gpio {
|
||||
compatible = "realtek,rtl8231-gpio";
|
||||
#gpio-cells = <2>;
|
||||
indirect-access-bus-id = <3>;
|
||||
gpio-controller;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
gpio-restart {
|
||||
compatible = "gpio-restart";
|
||||
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
mode {
|
||||
label = "reset";
|
||||
gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
/* i2c of the left SFP cage: port 49 */
|
||||
i2c0: i2c-gpio-0 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio1 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
sfp0: sfp-p9 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c0>;
|
||||
los-gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&gpio1 26 GPIO_ACTIVE_LOW>;
|
||||
tx-disable-gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
/* i2c of the right SFP cage: port 50 */
|
||||
i2c1: i2c-gpio-1 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
sfp1: sfp-p10 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c1>;
|
||||
los-gpio = <&gpio1 33 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&gpio1 32 GPIO_ACTIVE_LOW>;
|
||||
tx-disable-gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@50000 {
|
||||
label = "u-boot-env2";
|
||||
reg = <0x50000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@60000 {
|
||||
label = "jffs";
|
||||
reg = <0x60000 0x100000>;
|
||||
};
|
||||
partition@160000 {
|
||||
label = "jffs2";
|
||||
reg = <0x160000 0x100000>;
|
||||
};
|
||||
partition@b260000 {
|
||||
label = "firmware";
|
||||
reg = <0x260000 0xda0000>;
|
||||
compatible = "openwrt,uimage", "denx,uimage";
|
||||
openwrt,ih-magic = <0x83800000>;
|
||||
};
|
||||
partition@930000 {
|
||||
label = "runtime2";
|
||||
reg = <0x930000 0x6d0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet0 {
|
||||
mdio: mdio-bus {
|
||||
compatible = "realtek,rtl838x-mdio";
|
||||
regmap = <ðernet0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/* External phy RTL8218B #1 */
|
||||
EXTERNAL_PHY(0)
|
||||
EXTERNAL_PHY(1)
|
||||
EXTERNAL_PHY(2)
|
||||
EXTERNAL_PHY(3)
|
||||
EXTERNAL_PHY(4)
|
||||
EXTERNAL_PHY(5)
|
||||
EXTERNAL_PHY(6)
|
||||
EXTERNAL_PHY(7)
|
||||
|
||||
/* External phy RTL8218B #2 */
|
||||
EXTERNAL_PHY(8)
|
||||
EXTERNAL_PHY(9)
|
||||
EXTERNAL_PHY(10)
|
||||
EXTERNAL_PHY(11)
|
||||
EXTERNAL_PHY(12)
|
||||
EXTERNAL_PHY(13)
|
||||
EXTERNAL_PHY(14)
|
||||
EXTERNAL_PHY(15)
|
||||
|
||||
/* External phy RTL8218B #3 */
|
||||
EXTERNAL_PHY(16)
|
||||
EXTERNAL_PHY(17)
|
||||
EXTERNAL_PHY(18)
|
||||
EXTERNAL_PHY(19)
|
||||
EXTERNAL_PHY(20)
|
||||
EXTERNAL_PHY(21)
|
||||
EXTERNAL_PHY(22)
|
||||
EXTERNAL_PHY(23)
|
||||
|
||||
/* External phy RTL8218B #4 */
|
||||
EXTERNAL_PHY(24)
|
||||
EXTERNAL_PHY(25)
|
||||
EXTERNAL_PHY(26)
|
||||
EXTERNAL_PHY(27)
|
||||
EXTERNAL_PHY(28)
|
||||
EXTERNAL_PHY(29)
|
||||
EXTERNAL_PHY(30)
|
||||
EXTERNAL_PHY(31)
|
||||
|
||||
/* External phy RTL8218B #5 */
|
||||
EXTERNAL_PHY(32)
|
||||
EXTERNAL_PHY(33)
|
||||
EXTERNAL_PHY(34)
|
||||
EXTERNAL_PHY(35)
|
||||
EXTERNAL_PHY(36)
|
||||
EXTERNAL_PHY(37)
|
||||
EXTERNAL_PHY(38)
|
||||
EXTERNAL_PHY(39)
|
||||
|
||||
/* External phy RTL8218B #6 */
|
||||
EXTERNAL_PHY(40)
|
||||
EXTERNAL_PHY(41)
|
||||
EXTERNAL_PHY(42)
|
||||
EXTERNAL_PHY(43)
|
||||
EXTERNAL_PHY(44)
|
||||
EXTERNAL_PHY(45)
|
||||
EXTERNAL_PHY(46)
|
||||
EXTERNAL_PHY(47)
|
||||
|
||||
/* RTL8393 Internal SerDes */
|
||||
INTERNAL_PHY(48)
|
||||
INTERNAL_PHY(49)
|
||||
};
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
SWITCH_PORT(0, 01, qsgmii)
|
||||
SWITCH_PORT(1, 02, qsgmii)
|
||||
SWITCH_PORT(2, 03, qsgmii)
|
||||
SWITCH_PORT(3, 04, qsgmii)
|
||||
SWITCH_PORT(4, 05, qsgmii)
|
||||
SWITCH_PORT(5, 06, qsgmii)
|
||||
SWITCH_PORT(6, 07, qsgmii)
|
||||
SWITCH_PORT(7, 08, qsgmii)
|
||||
|
||||
SWITCH_PORT(8, 09, qsgmii)
|
||||
SWITCH_PORT(9, 10, qsgmii)
|
||||
SWITCH_PORT(10, 11, qsgmii)
|
||||
SWITCH_PORT(11, 12, qsgmii)
|
||||
SWITCH_PORT(12, 13, qsgmii)
|
||||
SWITCH_PORT(13, 14, qsgmii)
|
||||
SWITCH_PORT(14, 15, qsgmii)
|
||||
SWITCH_PORT(15, 16, qsgmii)
|
||||
|
||||
SWITCH_PORT(16, 17, qsgmii)
|
||||
SWITCH_PORT(17, 18, qsgmii)
|
||||
SWITCH_PORT(18, 19, qsgmii)
|
||||
SWITCH_PORT(19, 20, qsgmii)
|
||||
SWITCH_PORT(20, 21, qsgmii)
|
||||
SWITCH_PORT(21, 22, qsgmii)
|
||||
SWITCH_PORT(22, 23, qsgmii)
|
||||
SWITCH_PORT(23, 24, qsgmii)
|
||||
|
||||
SWITCH_PORT(24, 25, qsgmii)
|
||||
SWITCH_PORT(25, 26, qsgmii)
|
||||
SWITCH_PORT(26, 27, qsgmii)
|
||||
SWITCH_PORT(27, 28, qsgmii)
|
||||
SWITCH_PORT(28, 29, qsgmii)
|
||||
SWITCH_PORT(29, 30, qsgmii)
|
||||
SWITCH_PORT(30, 31, qsgmii)
|
||||
SWITCH_PORT(31, 32, qsgmii)
|
||||
|
||||
SWITCH_PORT(32, 33, qsgmii)
|
||||
SWITCH_PORT(33, 34, qsgmii)
|
||||
SWITCH_PORT(34, 35, qsgmii)
|
||||
SWITCH_PORT(35, 36, qsgmii)
|
||||
SWITCH_PORT(36, 37, qsgmii)
|
||||
SWITCH_PORT(37, 38, qsgmii)
|
||||
SWITCH_PORT(38, 39, qsgmii)
|
||||
SWITCH_PORT(39, 40, qsgmii)
|
||||
|
||||
SWITCH_PORT(40, 41, qsgmii)
|
||||
SWITCH_PORT(41, 42, qsgmii)
|
||||
SWITCH_PORT(42, 43, qsgmii)
|
||||
SWITCH_PORT(43, 44, qsgmii)
|
||||
SWITCH_PORT(44, 45, qsgmii)
|
||||
SWITCH_PORT(45, 46, qsgmii)
|
||||
SWITCH_PORT(46, 47, qsgmii)
|
||||
SWITCH_PORT(47, 48, qsgmii)
|
||||
|
||||
/* SFP cages */
|
||||
port@48 {
|
||||
reg = <48>;
|
||||
label = "lan49";
|
||||
phy-mode = "sgmii";
|
||||
phy-handle = <&phy48>;
|
||||
sfp = <&sfp0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
port@49 {
|
||||
reg = <49>;
|
||||
label = "lan50";
|
||||
phy-mode = "sgmii";
|
||||
phy-handle = <&phy49>;
|
||||
sfp = <&sfp1>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
/* CPU-Port */
|
||||
port@52 {
|
||||
ethernet = <ðernet0>;
|
||||
reg = <52>;
|
||||
phy-mode = "qsgmii";
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
13
target/linux/realtek/image/rtl839x.mk
Normal file
13
target/linux/realtek/image/rtl839x.mk
Normal file
|
|
@ -0,0 +1,13 @@
|
|||
# SPDX-License-Identifier: GPL-2.0-only
|
||||
|
||||
define Device/zyxel_gs1900-48
|
||||
SOC := rtl8393
|
||||
IMAGE_SIZE := 13952k
|
||||
DEVICE_VENDOR := ZyXEL
|
||||
UIMAGE_MAGIC := 0x83800000
|
||||
ZYXEL_VERS := AAHO
|
||||
DEVICE_MODEL := GS1900-48
|
||||
KERNEL_INITRAMFS := kernel-bin | append-dtb | gzip | zyxel-vers $$$$(ZYXEL_VERS) | \
|
||||
uImage gzip
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_gs1900-48
|
||||
Loading…
Reference in New Issue
Block a user