ath79: add support for TP-Link RE450 v2

TP-Link RE450 v2 is a dual band router/range-extender
based on Qualcomm/Atheros QCA9563 + QCA9880.

Specification:

- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button
- UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers)

Flash instruction:
Apply factory image in OEM firmware web-gui.

U-Boot does not seem to have any recovery functions, so
debricking requires connection via UART.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
This commit is contained in:
Peter Lundkvist 2018-06-29 05:44:58 +02:00 committed by John Crispin
parent f4ac88b509
commit 781ad46206
7 changed files with 263 additions and 1 deletions

View File

@ -28,6 +28,10 @@ case "$board" in
ucidef_set_led_switch "lan1" "LAN1" "netgear:green:lan1" "switch0" "0x02" "0x0f"
ucidef_set_led_switch "lan2" "LAN2" "netgear:green:lan2" "switch0" "0x04" "0x0f"
;;
"tplink,re450-v2")
ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"
;;
"tplink,tl-mr3020-v1")
ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x02"
;;

View File

@ -13,6 +13,7 @@ ath79_setup_interfaces()
ucidef_set_interface_lan "eth0" "dhcp"
;;
"avm,fritz300e"|\
"tplink,re450-v2"|\
"tplink,tl-mr10u"|\
"tplink,tl-wr703n"|\
"ubnt,unifiac-lite"|\

View File

@ -91,6 +91,10 @@ case "$FIRMWARE" in
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
"tplink,re450-v2")
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
"tplink,tl-archer-c7-v2")
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)

View File

@ -0,0 +1,195 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca956x.dtsi"
/ {
compatible = "tplink,re450-v2", "qca,qca9563";
model = "TP-Link RE450 v2";
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-status = &system;
mdio-gpio0 = &mdio2;
};
leds {
compatible = "gpio-leds";
system: power {
label = "tp-link:blue:power";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
};
wlan2g {
label = "tp-link:blue:wlan2g";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy1tpt";
};
wlan5g {
label = "tp-link:blue:wlan5g";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
lan_link {
label = "tp-link:green:lan_link";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
default-state = "off";
};
lan_data {
label = "tp-link:green:lan_data";
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
default-state = "off";
};
wps_blue {
label = "tp-link:blue:wps";
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
wps_red {
label = "tp-link:red:wps";
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
reset {
label = "Reset button";
linux,code = <KEY_RESTART>;
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
power {
label = "Power button";
linux,code = <KEY_POWER>;
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
leds {
label = "LED control button";
linux,code = <BTN_0>;
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wps {
label = "WPS button";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
mdio2: mdio {
compatible = "virtual,mdio-gpio";
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>, /* MDC */
<&gpio 4 GPIO_ACTIVE_HIGH>; /* MDIO */
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@4 {
reg = <4>;
device_type = "ethernet-phy";
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
};
};
&pcie {
status = "okay";
};
&uart {
status = "okay";
};
&gpio {
status = "okay";
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x020000>;
read-only;
};
partition@20000 {
label = "firmware";
reg = <0x020000 0x5e0000>;
};
partition@600000 {
label = "partition-table";
reg = <0x600000 0x010000>;
read-only;
};
info: partition@610000 {
label = "product-info";
reg = <0x610000 0x020000>;
read-only;
};
partition@630000 {
label = "config";
reg = <0x630000 0x020000>;
read-only;
};
art: partition@7f0000 {
label = "art";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&info 0x8>;
phy-handle = <&phy0>;
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&info 0x8>;
};

View File

@ -1,4 +1,4 @@
DEVICE_VARS += TPLINK_HWID TPLINK_HWREV TPLINK_FLASHLAYOUT TPLINK_HEADER_VERSION TPLINK_BOARD_NAME
DEVICE_VARS += TPLINK_HWID TPLINK_HWREV TPLINK_FLASHLAYOUT TPLINK_HEADER_VERSION TPLINK_BOARD_NAME TPLINK_BOARD_ID
define rootfs_align
$(patsubst %-256k,0x40000,$(patsubst %-128k,0x20000,$(patsubst %-64k,0x10000,$(patsubst squashfs%,0x4,$(patsubst root.%,%,$(1))))))

View File

@ -13,6 +13,24 @@ define Device/tl-archer-c7-v2
endef
TARGET_DEVICES += tl-archer-c7-v2
define Device/tl-re450-v2
$(Device/tplink)
ATH_SOC := qca9563
IMAGE_SIZE := 6016k
DEVICE_TITLE := TP-LINK RE450 v2
DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
TPLINK_HWID := 0x0
TPLINK_HWREV := 0
TPLINK_BOARD_ID := RE450-V2
LOADER_TYPE := elf
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header -O
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \
append-metadata | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
SUPPORTED_DEVICES := tplink,re450-v2
endef
TARGET_DEVICES += tl-re450-v2
define Device/tl-wdr3600
$(Device/tplink-8mlzma)
ATH_SOC := ar9344

View File

@ -1079,6 +1079,46 @@ static struct device_info boards[] = {
.last_sysupgrade_partition = "file-system"
},
/** Firmware layout for the RE450 v2 */
{
.id = "RE450-V2",
.vendor = "",
.support_list =
"SupportList:\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:00000000}\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:55530000}\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:45550000}\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:4A500000}\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:43410000}\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:41550000}\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:41530000}\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:4B520000}\r\n"
"{product_name:RE450,product_ver:2.0.0,special_id:42520000}\r\n",
.support_trail = '\x00',
.soft_ver = NULL,
/* We're using a dynamic kernel/rootfs split here */
.partitions = {
{"fs-uboot", 0x00000, 0x20000},
{"firmware", 0x20000, 0x5e0000},
{"partition-table", 0x600000, 0x02000},
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
{"soft-version", 0x620000, 0x01000},
{"support-list", 0x621000, 0x01000},
{"profile", 0x622000, 0x08000},
{"user-config", 0x630000, 0x10000},
{"default-config", 0x640000, 0x10000},
{"radio", 0x7f0000, 0x10000},
{NULL, 0, 0}
},
.first_sysupgrade_partition = "os-image",
.last_sysupgrade_partition = "file-system"
},
{}
};