ath79: add support for OpenMesh OM2P-HS v1
Device specifications:
======================
* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 802.3af POE
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[drop redundant status from eth1]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Sven Eckelmann
Adrian Schmutzler
parent
dbb542f194
commit
a462412977
|
|
@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk
|
|||
PKG_NAME:=uboot-envtools
|
||||
PKG_DISTNAME:=u-boot
|
||||
PKG_VERSION:=2020.04
|
||||
PKG_RELEASE:=11
|
||||
PKG_RELEASE:=12
|
||||
|
||||
PKG_SOURCE:=$(PKG_DISTNAME)-$(PKG_VERSION).tar.bz2
|
||||
PKG_SOURCE_URL:= \
|
||||
|
|
|
|||
|
|
@ -86,6 +86,7 @@ netgear,wndr4300sw)
|
|||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x20000"
|
||||
;;
|
||||
openmesh,om2p-v4|\
|
||||
openmesh,om2p-hs-v1|\
|
||||
openmesh,om2p-hs-v4|\
|
||||
plasmacloud,pa300|\
|
||||
plasmacloud,pa300e)
|
||||
|
|
|
|||
8
target/linux/ath79/dts/ar9341_openmesh_om2p-hs-v1.dts
Normal file
8
target/linux/ath79/dts/ar9341_openmesh_om2p-hs-v1.dts
Normal file
|
|
@ -0,0 +1,8 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "ar9341_openmesh_om2p-hs.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "openmesh,om2p-hs-v1", "qca,ar9341";
|
||||
model = "OpenMesh OM2P-HS v1";
|
||||
};
|
||||
161
target/linux/ath79/dts/ar9341_openmesh_om2p-hs.dtsi
Normal file
161
target/linux/ath79/dts/ar9341_openmesh_om2p-hs.dtsi
Normal file
|
|
@ -0,0 +1,161 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "ar9341.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
/delete-property/ bootargs;
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &uart;
|
||||
led-boot = &led_power_blue;
|
||||
led-failsafe = &led_power_blue;
|
||||
led-running = &led_power_blue;
|
||||
led-upgrade = &led_power_blue;
|
||||
label-mac-device = ð1;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins &led_lan_wan_blue_pin>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_blue: power_blue {
|
||||
label = "blue:power";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wifi_green {
|
||||
label = "green:wifi";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wifi_red {
|
||||
label = "red:wifi";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi_yellow {
|
||||
label = "yellow:wifi";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan_blue {
|
||||
label = "blue:lan";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_blue {
|
||||
label = "blue:wan";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
/* hw_margin_ms is actually 300s but driver limits it to 60s */
|
||||
hw_margin_ms = <60000>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
led_lan_wan_blue_pin: pinmux_lan_wan_blue_pin {
|
||||
pinctrl-single,bits = <0x10 0x0 0x0000ffff>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <40000000>;
|
||||
|
||||
/* partitions are passed via bootloader */
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x040000>;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "custom";
|
||||
reg = <0x080000 0x140000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1c0000 {
|
||||
label = "inactive";
|
||||
reg = <0x1c0000 0x700000>;
|
||||
};
|
||||
|
||||
partition@8c0000 {
|
||||
label = "inactive2";
|
||||
reg = <0x8c0000 0x700000>;
|
||||
};
|
||||
|
||||
art: partition@fc0000 {
|
||||
label = "ART";
|
||||
reg = <0xfc0000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&swphy4>;
|
||||
|
||||
mtd-mac-address = <&art 0x6>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
};
|
||||
|
|
@ -145,6 +145,7 @@ comfast,cf-e560ac)
|
|||
ucidef_set_led_switch "lan4" "LAN4" "blue:lan4" "switch0" "0x10"
|
||||
;;
|
||||
comfast,cf-ew72|\
|
||||
openmesh,om2p-hs-v1|\
|
||||
telco,t1)
|
||||
ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02"
|
||||
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
|
||||
|
|
|
|||
|
|
@ -51,6 +51,7 @@ platform_do_upgrade() {
|
|||
redboot_fis_do_upgrade "$1" linux
|
||||
;;
|
||||
openmesh,om2p-v4|\
|
||||
openmesh,om2p-hs-v1|\
|
||||
openmesh,om2p-hs-v4)
|
||||
PART_NAME="inactive"
|
||||
platform_do_upgrade_openmesh "$1"
|
||||
|
|
|
|||
|
|
@ -1577,6 +1577,15 @@ define Device/openmesh_om2p-v4
|
|||
endef
|
||||
TARGET_DEVICES += openmesh_om2p-v4
|
||||
|
||||
define Device/openmesh_om2p-hs-v1
|
||||
$(Device/openmesh_om2p-common)
|
||||
SOC := ar9341
|
||||
DEVICE_MODEL := OM2P-HS
|
||||
DEVICE_VARIANT := v1
|
||||
SUPPORTED_DEVICES += om2p-hs
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_om2p-hs-v1
|
||||
|
||||
define Device/openmesh_om2p-hs-v4
|
||||
$(Device/openmesh_om2p-common)
|
||||
SOC := qca9533
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user