ramips: add support for netis WF2770

netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- UART:
  - J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit is contained in:
Sungbo Eo 2019-11-12 01:23:07 +09:00 committed by Adrian Schmutzler
parent 46674723e1
commit a4e9c8f14b
5 changed files with 183 additions and 6 deletions

View File

@ -0,0 +1,161 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7620a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "netis,wf2770", "ralink,mt7620a-soc";
model = "NETIS WF2770";
leds {
compatible = "gpio-leds";
wlan {
label = "wf2770:blue:wlan";
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
rfkill {
label = "rfkill";
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
led-toggle {
label = "led-toggle";
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_LIGHTS_TOGGLE>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x50000 0xfb0000>;
};
};
};
};
&state_default {
gpio {
groups = "i2c", "uartf";
function = "gpio";
};
};
&ethernet {
pinctrl-names = "default";
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
mtd-mac-address = <&factory 0x4>;
port@5 {
status = "okay";
mediatek,fixed-link = <1000 1 1 1>;
phy-mode = "rgmii";
};
mdio-bus {
status = "okay";
ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
};
ethernet-phy@1 {
reg = <1>;
phy-mode = "rgmii";
};
ethernet-phy@2 {
reg = <2>;
phy-mode = "rgmii";
};
ethernet-phy@3 {
reg = <3>;
phy-mode = "rgmii";
};
ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii";
};
ethernet-phy@1f {
reg = <0x1f>;
phy-mode = "rgmii";
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&wmac {
ralink,mtd-eeprom = <&factory 0x0>;
};

View File

@ -100,6 +100,12 @@ define Build/mkdlinkfw-factory
mv $@.new $@
endef
define Build/netis-tail
echo -n $(1) >> $@
echo -n $(UIMAGE_NAME)-yun | $(STAGING_DIR_HOST)/bin/mkhash md5 | \
sed 's/../\\\\x&/g' | xargs echo -ne >> $@
endef
define Build/poray-header
$(STAGING_DIR_HOST)/bin/mkporayfw $(1) -f $@ -o $@.new
mv $@.new $@

View File

@ -700,6 +700,17 @@ define Device/netgear_wn3000rp-v3
endef
TARGET_DEVICES += netgear_wn3000rp-v3
define Device/netis_wf2770
SOC := mt7620a
IMAGE_SIZE := 16064k
UIMAGE_NAME := WF2770_0.0.00
DEVICE_VENDOR := NETIS
DEVICE_MODEL := WF2770
DEVICE_PACKAGES := kmod-mt76x0e
KERNEL_INITRAMFS := $(KERNEL_DTB) | netis-tail WF2770 | uImage lzma
endef
TARGET_DEVICES += netis_wf2770
define Device/nexx_wt3020-4m
SOC := mt7620n
BLOCKSIZE := 4k

View File

@ -81,12 +81,6 @@ define Build/iodata-mstc-header
)
endef
define Build/netis-tail
echo -n $(1) >> $@
echo -n $(UIMAGE_NAME)-yun | $(STAGING_DIR_HOST)/bin/mkhash md5 | \
sed 's/../\\\\x&/g' | xargs echo -ne >> $@
endef
define Build/ubnt-erx-factory-image
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
echo '21001:6' > $(1).compat; \

View File

@ -170,6 +170,7 @@ ramips_setup_interfaces()
"1:lan:4" "2:lan:3" "4:lan:2" "5:lan:1" "0:wan" "6@eth0"
;;
linksys,e1700|\
netis,wf2770|\
ralink,mt7620a-mt7530-evb)
ucidef_add_switch "switch0"
ucidef_add_switch_attr "switch0" "enable" "false"
@ -338,6 +339,10 @@ ramips_setup_macs()
linksys,e1700)
wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
;;
netis,wf2770)
wan_mac=$(mtd_get_mac_binary factory 0x2e)
label_mac=$wan_mac
;;
tplink,archer-c2-v1|\
tplink,archer-c20-v1|\
tplink,archer-c20i|\