ath79: support for TP-Link EAP225-Wall v2
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Sander Vanheule
Adrian Schmutzler
parent
53df30f02b
commit
c9f51a9ad6
146
target/linux/ath79/dts/qca9561_tplink_eap225-wall-v2.dts
Normal file
146
target/linux/ath79/dts/qca9561_tplink_eap225-wall-v2.dts
Normal file
|
|
@ -0,0 +1,146 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,eap225-wall-v2", "qca,qca9561";
|
||||
model = "TP-Link EAP225-Wall v2";
|
||||
|
||||
aliases {
|
||||
label-mac-device = ð1;
|
||||
led-boot = &led_status;
|
||||
led-failsafe = &led_status;
|
||||
led-running = &led_status;
|
||||
led-upgrade = &led_status;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
led {
|
||||
label = "LED button";
|
||||
linux,code = <KEY_LIGHTS_TOGGLE>;
|
||||
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status: status {
|
||||
label = "tp-link:white:status";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
};
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
|
||||
poe_passthrough {
|
||||
gpio-export,name = "tp-link:poe-passthrough:enable";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "partition-table";
|
||||
reg = <0x020000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
info: partition@30000 {
|
||||
label = "info";
|
||||
reg = <0x030000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
compatible = "openwrt,elf";
|
||||
label = "firmware";
|
||||
reg = <0x040000 0xd80000>;
|
||||
};
|
||||
|
||||
partition@dc0000 {
|
||||
label = "config";
|
||||
reg = <0xdc0000 0x030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* df0000-f30000 undefined in vendor firmware */
|
||||
|
||||
partition@f30000 {
|
||||
label = "mutil-log";
|
||||
reg = <0xf30000 0x080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fb0000 {
|
||||
label = "oops";
|
||||
reg = <0xfb0000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&info 0x8>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&info 0x8>;
|
||||
};
|
||||
|
|
@ -302,6 +302,10 @@ ath79_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"0@eth1" "3:lan:3" "4:lan:2" "5:lan:1" "6@eth0" "2:wan:4" "1:wan:5"
|
||||
;;
|
||||
tplink,eap225-wall-v2)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
|
||||
;;
|
||||
tplink,eap245-v3)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan:1" "5:lan:2"
|
||||
|
|
|
|||
|
|
@ -206,6 +206,12 @@ case "$FIRMWARE" in
|
|||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
tplink,eap225-wall-v2)
|
||||
caldata_extract "art" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
|
||||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
tplink,eap245-v3)
|
||||
caldata_extract "art" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
|
||||
|
|
|
|||
|
|
@ -364,7 +364,6 @@ TARGET_DEVICES += tplink_cpe610-v2
|
|||
|
||||
define Device/tplink-eap2x5
|
||||
$(Device/tplink-safeloader)
|
||||
SOC := qca9563
|
||||
LOADER_TYPE := elf
|
||||
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel
|
||||
KERNEL_INITRAMFS := $$(KERNEL)
|
||||
|
|
@ -372,8 +371,20 @@ define Device/tplink-eap2x5
|
|||
pad-extra 128
|
||||
endef
|
||||
|
||||
define Device/tplink_eap225-wall-v2
|
||||
$(Device/tplink-eap2x5)
|
||||
SOC := qca9561
|
||||
IMAGE_SIZE := 13824k
|
||||
DEVICE_MODEL := EAP225-Wall
|
||||
DEVICE_VARIANT := v2
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
TPLINK_BOARD_ID := EAP225-WALL-V2
|
||||
endef
|
||||
TARGET_DEVICES += tplink_eap225-wall-v2
|
||||
|
||||
define Device/tplink_eap245-v3
|
||||
$(Device/tplink-eap2x5)
|
||||
SOC := qca9563
|
||||
IMAGE_SIZE := 14592k
|
||||
DEVICE_MODEL := EAP245
|
||||
DEVICE_VARIANT := v3
|
||||
|
|
|
|||
|
|
@ -1298,6 +1298,35 @@ static struct device_info boards[] = {
|
|||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the EAP225-Wall v2 */
|
||||
{
|
||||
.id = "EAP225-WALL-V2",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"EAP225-Wall(TP-Link|UN|AC1200-D):2.0\r\n",
|
||||
.support_trail = '\xff',
|
||||
.soft_ver = NULL,
|
||||
.soft_ver_compat_level = 1,
|
||||
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"partition-table", 0x20000, 0x02000},
|
||||
{"default-mac", 0x30000, 0x01000},
|
||||
{"support-list", 0x31000, 0x00100},
|
||||
{"product-info", 0x31100, 0x00400},
|
||||
{"soft-version", 0x32000, 0x00100},
|
||||
{"firmware", 0x40000, 0xd80000},
|
||||
{"user-config", 0xdc0000, 0x30000},
|
||||
{"mutil-log", 0xf30000, 0x80000},
|
||||
{"oops", 0xfb0000, 0x40000},
|
||||
{"radio", 0xff0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the EAP245 v3 */
|
||||
{
|
||||
.id = "EAP245-V3",
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user