Before this change UCI sections of both types were parsed in order as
specified in UCI. That didn't work well with all drivers (e.g. b53).
It seems that VLAN setup can reset / overwrite previously set ports
parameters. It resulted in "switch_port" options defined above
"switch_vlan"s being silently ignored.
Ideally swconfig & all drivers should be improved to handle that
properly but it'd be a waste of time at this point as DSA replaces
swconfig. Use this minor parsing change as a quick fix.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223
Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
7. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | A4:xx:xx:51:xx:F4 | No MACs was |
| LAN | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN | A4:xx:xx:51:xx:F4 | [1] |
| WLAN_2g | A4:xx:xx:51:xx:F5 | |
| WLAN_5g | A6:xx:xx:21:xx:F5 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
"Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
MTS WG430223 devices even within the same broadcast domain.
Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset | | Description |
+==============+===============+========================================+
| 0x0 | 31 52 48 53 | TRX magic "1RHS" |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Fix hostapd feature detection after the bump to 2022-05-08.
getopt was not updated correctly after upstream added support for -q arg.
This reenables feature detection so that LuCi can check for features like
SAE, fast roaming etc.
Fixes: c35ff1affe ("hostapd: update to 2022-05-08")
Signed-off-by: Robert Marko <robimarko@gmail.com>
902b321 wireless-regdb: Update regulatory rules for Israel (IL)
20f6f34 wireless-regdb: add missing spaces for US S1G rules
25652b6 wireless-regdb: Update regulatory rules for Australia (AU)
081873f wireless-regdb: update regulatory database based on preceding changes
166fbdd wireless-regdb: add db files missing from previous commit
e3f03f9 Regulatory update for 6 GHz operation in Canada (CA)
888da5f Regulatory update for 6 GHz operation in United States (US)
647bcaa Regulatory update for 6 GHz operation in FI
c6b079d wireless-regdb: update regulatory rules for Bulgaria (BG) on 6GHz
2ed39be wireless-regdb: Remove AUTO-BW from 6 GHz rules
7a6ad1a wireless-regdb: Unify 6 GHz rules for EU contries
68a8f2f wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7e06706 iw: event: report missing radar events
5909e73 iw: survey: add support for radio stats
64bf570 update nl80211.h
0900996 iw: print Radar background capability if supported
56c6077 iw: print out assoc comeback event
a4e5418 iw: support 160MHz frequency command for 6GHz band
5a71b72 iw: Print local EHT capabilities
e3287a1 station: print EHT rate information
ff67fb2 iw: fix double tab in mesh path header
05a5267 iw: fix 'upto' -> 'up to'
00a2985 iw: handle VHT extended NSS
82e0bd1 update nl80211.h
c95877c info: add missing extended features
0976378 info: refactor extended features
79f20cb bump version to 5.19
Sync nl80211.h with our version of mac80211 and remove parts of the iw
code that are not supported by our version of mac80211.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Sync nl80211.h with upstream in order to maintain parity with
nl80211_copy.h shipped with hostapd.
This is necessary, as currently the enum value for
NL80211_EXT_FEATURE_RADAR_BACKGROUND mismatches between hostapd and
mac80211. This breaks background radar capability detection in hostapd.
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
Openvpn forces CONFIG_WOLFSSL_HAS_OPENVPN=y. When the phase1 bots build
the now non-shared package, openvpn will not be selected, and WolfSSL
will be built without it. Then phase2 bots have CONFIG_ALL=y, which
will select openvpn and force CONFIG_WOLFSSL_HAS_OPENVPN=y. This
changes the version hash, causing dependency failures, as shared
packages expect the phase2 hash.
Fixes: #9738
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
libwolfssl-benchmark should NOT be compiled as nonshared but
currently there is a bug where, on buildbot stage2, the package
is recompiled to build libwolfssl-benchmark and the dependency
change to the new libwolfssl version.
Each dependant package will now depend on the new wolfssl package
instead of the one previously on stage1 that has a different package
HASH.
Set the nonshared PKGFLAGS global while this gets investigated
and eventually fixed.
Fixes: 0a2edc2714 ("wolfssl: enable CPU crypto instructions")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
commit c3a4cddaaf ("hostapd: remove hostapd-hs20 variant")
as well as
commit 9f1927173a ("hostapd: wpas: add missing config symbols")
indicate hostapd-full should support Hotspot 2.0 already, but only
wpa_supplicant (and wpad) do.
How this happened is not really clear, as no commit adding support for
Hotspot 2.0 is in the history.
Fix this and add Hotspot 2.0 capability to hostapd-full.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the current BSS color to hostapd get_status method. This field is
set to -1 in case BSS color is not active for the BSS.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
In case no specific BSS color is configured, set it to a random value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Update hostapd to Git HEAD from 2022-05-08. This allows us to take
advantage of background radar-detection as well as BSS color collision
detection.
Suggested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
This patch allows the user to set `auth_server` and related settings on
non WPA2 Enterprise AP modes in `/etc/config/wireless`, too, so the
Radius Attributes for Dynamic VLAN Assignment can be fetched from Radius.
Without this patch, `auth_server` and other needed options are only
written to `hostapd-phy<n>.conf` when `option encryption wpa2` is set.
`hostapd` however supports "Station MAC address -based authentication" for
non WPA Enterprise Modes, too.
A classic approch is to use `accept_mac_file` which contains MAC addr
and VLAN-ID pairs. But, using `accept_mac_file` does not support
VLAN assignment for unknown stations.
This is a sample `freeradius3` config, where a known station
("7e:a6:a7:2a:93:d2") is assigned to VLAN `65` and unknown stations are
assigned to VLAN `67`.
```
"7ea6a72a93d2" Cleartext-Password := "7ea6a72a93d2"
Tunnel-Type = "VLAN",
Tunnel-Medium-Type = "IEEE-802",
Tunnel-Private-Group-Id = 65
DEFAULT Cleartext-Password := "%{User-Name}"
Tunnel-Type = "VLAN",
Tunnel-Medium-Type = "IEEE-802",
Tunnel-Private-Group-Id = 67
```
Other option is to configure known stations via `accept_mac_file` and
using only Radius for unknown stations.
I tested this patch only with `wpa_key_mgmt=WPA-PSK`, and assumed that
it should work with other Encryption/Access Mode, too.
Signed-off-by: Bernd Naumann <bernd.naumann@kr217.de>
This enables AES & SHA CPU instructions for compatible armv8, and x86_64
architectures. Add this to the hardware acceleration choice, since they
can't be enabled at the same time.
The package was marked non-shared, since the arm CPUs may or may not
have crypto extensions enabled based on licensing; bcm27xx does not
enable them. There is no run-time detection of this for arm.
NOTE:
Should this be backported to a release branch, it must be done shortly
before a new minor release, because the change to nonshared will remove
libwolfssl from the shared packages, but the nonshared are only built in
a subsequent release!
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Enabling different hardware crypto acceleration should not change the
library ABI. Add them to PKG_CONFIG_DEPENDS after the ABI version hash
has been computed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.
Specifications
--------------
* Device: ZyXEL GS1900-24E
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet: 24x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Switch: 1 Power switch on rear of device
* Power 120-240V AC C13
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
All known users of this ubus method have been updated to use the new
bss_transition_request method instead.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Major changes are:
Add support for smbd-direct multi-desctriptor.
Add support for dkms.
Add support for key exchange.
Fix seveal bugs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Make ar8216/8327 swconfig driver modularizable and add
entry to the netdevices.mk kernel modules file.
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
latency and short-term fairness is improved by fixing the tx queue sorting
so that it considers the pending AQL budget
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Needed by strongSwan IPsec VPN for strongswan-mod-chapoly. Not to be confused with
kmod-crypto-LIB-chacha20poly1305, which is an 8-byte nonce version used
by wireguard.
Signed-off-by: Xu Wang <xwang1498@gmx.com>
Aruba deploys a BDF in the root filesystem, however this matches the one
used for the DK04 reference board.
The board-specific BDFs are built into the kernel. The AP-365 shows
sinificant degraded performance with increased range when used with the
reference BDF.
Replace the BDF with the one extracted from Arubas kernel.
Signed-off-by: David Bauer <mail@david-bauer.net>
2f793a4 lua: add optional path filter to objects() method
2bebf93 ubusd: handle invoke on event object without data
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2e1fcf4 netifd: fix hwmode for 60g band
39ef9fe interface-ip: fix memory corruption bug when using jail network namespaces
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
557c98e init: selinux: don't relabel virtual filesystems
7a00968 init: only relabel rootfs if started from initramfs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
210991d fw4: prefer /dev/stdin if available
4e5e322 fw4: make `fw4 restart` behavior more robust
221040e ruleset: emit time ranges when both start and stop times are specified
30a7d47 fw4: fix datetime parsing
fb9a6b2 ruleset: correct mangle_output chain type
6dd2617 fw4: fix logic flaw in testing hw flow offloading support
c7c9c84 fw4: ensure that negative bitcounts are properly translated
c4a78ed fw4: fix typo in emitted set types
Fixes: #9764, #9923, #9927, #9935, #9955
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add ieee80211_rx_check_bss_color_collision routine in order to introduce
BSS color collision detection in mac80211 if it is not supported in HW/FW
(e.g. for mt7915 chipset).
Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify
BSS color collision detection is supported in HW/FW. Set this for ath11k
which apparently didn't need this code.
Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org
[clarify commit message a bit, move flag to mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Buidbots are currently choking on the following compile error:
In file included from tools/aisimage.c:9:
include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory
# include <openssl/evp.h>
^~~~~~~~~~~~~~~
compilation terminated.
This is caused by a complete overriding of make flags which are provided
correctly in `UBOOT_MAKE_FLAGS` variable, but currently overriden
instead of extended. This then leads to the usage of build host include
dirs, which are not available.
Fix it by extending `UBOOT_MAKE_FLAGS` variable in all device recipes.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Original patch: https://github.com/cifsd-team/ksmbd-tools/issues/227
adapted for ksmbd kernel module v3.4.3 by me.
Fixes crash in v3.4.3 only. Use original patch when updating to v3.4.4
as this one will fail hunk #1.
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
4b4849cf5e5a interface-ip: unify host and proto route handling
507c0513d176 interface-ip: add support for excluding interfaces in host route lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
86ca9c6 devstatus: prints to terminal
95de949 deal with /rom/dev/console label inconsistencies
ab6b6ee uci: hack to deal with potentially mislabeled char files
acf9172 dnsmasq this can't be right
021db5b luci-app-tinyproxy
cf3a9c4 support/secmark: removes duplicate loopback rules
eeb2610 dhcp servers: recv dhcp client packets
d5a5fc3 more support/secmark "fixes"
35d8604 update support secmark
4c155c0 packets these were caused by labeling issues with loopback
fad35a5 nftables reads routing table
f9c5a04 umurmur: kill an mumur instance that does not run as root
10a10c6 mmc stordev make this consistent
ab3ec5b Makefile: sort with LC_ALL=C
b34eaa5 fwenv rules
8c2960f adds rfkill nodedev and some mmc partitions to stordev
5a9ffe9 rcboot runs fwenv with a transition
9954bf6 dnsmasq in case of tcp
ab66468 dnsmasq try this
5bfcb88 dnsmasq stubby not sure why this is happening
863f549 luci not sure why it recv and send server packets
d5cddb0 uhttpd sends sigkill luci cgi
44cc04d stubby: it does not maintain anything in there
db730b4 Adds stubby
ccbcf0e tor simplify network access
a308065 tor basic
a9c0163 znc loose ends
327a9af acme: allow acme_cleanup.sh to restart znc
4015614 basic znc
7ef14a2 support/secmark: clarify some things
3107afe README: todo qrencode
943035a README and secmark doc
4c90937 ttyd: fix that socket leak again
3239adf dnsmasq icmp packets and fix a tty leak issue
b41d38f Makefile: optimize
95d05b1 sandbox dontaudit ttyd leak
0b7d670 rpcd: reads mtu
e754bf1 opkg-lists try this
35fb530 opkg-lists: custom
4328754 opkg try to address mislabeled /tmp/opkg-lists
3e2385c rcnftqos
95eae2d ucode
c86d366 luci diagnostics
e10b443 rpcd packets and wireguard/luci
a25e020 igmpproxt packets
0106f00 luci
dcef79c nftqos related
3c9bc90 related to nft-qos and luci
f8502d4 dnsmasq more related to /usr/lib/dnsmasq/dhcp-script.sh
29a4271 dnsmasq: related to /usr/lib/dnsmasq/dhcp-script.sh
0c5805a some nft-qos
1100b41 adds a label for /tmp/.ujailnoafile
e141a83 initscript: i labeled ujail procd.execfile
a3b0302 Makefile: adds a default target + packets target
6a3f8ef label usign as opkg and label fwtool and sysupgrade
04d1cc7 sysupgrade: i meant don't do the fc spec
763bec0 sysupgrade: dont do /tmp/sysupgrade.img
af2306f adds a failsafe.tmpfile and labels validate_firmware_image
5b15760 fwenv: comment doesnt make sense
370ac3b fwenv: executes shell
67e3fcb fwenv: adds fw_setsys
544d211 adds procd execfile module to label procd related exec files
99d5f13 rclocalconffile: treat /etc/rc.button like /etc/rc.local
4dfd662 label uclient-fetch the same as wget
75d8212 osreleasemiscfile: adds /etc/device_info
0c1f116 adds a rcbuttonconffile for /etc/rc.button (base-files)
ccd23f8 adds a syslog.conffile for /etc/syslog.conf (busybox)
f790600 adds a libattr.conffile for /etc/xattr.conf
fcc028e fwenv: adds fwsys
1255470 xtables: various iptables alternatives
a7c4035 Revert "sqm: runs xtables, so also allow nftables"
0d331c3 sqm: runs xtables, so also allow nftables
f34076b acme: will run nftables in the near future
6217046 allow ssl.read types to read /tmp/etc/ssl/engines.cnf
d0deea3 fixes dns packets
8399efc Revert "sandbox: see if dontauditing this affects things"
73d716a sandbox: see if dontauditing this affects things
b5ee097 sandbox: also allow readinherited dropbear pipes
12ee46b iwinfo traverses /tmp/run/wpa_supplicant
4a4d724 agent.cil: also reads inherited dropbear pipes
d48013f support/secmark: i tightened my dns packet policy
645ad9e dns packets redone
4790b25 dnsnetpacket: fix obj macro template
d9fafff redo dns packets
0a68498 ttyd: leaks a netlink route socket
1d2e6be .gitattributes: remove todo
e1bb954 usbutil: reads bus sysfile symlinks
d275a32 support/secmark: clean it up a little
af5ce12 Makefile: exclude packet types in default make target
3caacdf support/secmark: document tunable/boolean
e3dd3e6 invalidpacketselinuxbool: make it build-time again
54f0ccf odhcpd packet fix
4a864ba contrib/secmark: add a big FAT warning
bead937 contrib/secmark: adds note about secmark support
146ae16 netpacket remove test
2ce9899 dns packets, odhcp6c raw packet, 4123 ntpnts for netnod
070a45f chrony and unbound packets
eba894f rawip socket packets cannot be labeled
656ae0b adds isakmp (500), ipsec-nat-t (4500) and rawip packet types
35325db adds igmp packet type
5cf444c adds icmp packet type
2e41304 sandbox some more packet access for sandbox net
12caad6 packet accesses
b8eb9a8 adds a trunkload of packet types
a42a336 move rules related to invalid netpeers and ipsec associations
a9e40e0 xtables/nftables allow relabelto all packet types
aa5a52c README: adds item to wish list
3a96eec experiment: simple label based packet filtering
26d6f95 nftables reads/writes fw pipes
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
c22eeef fw4: support negative CIDR bit notation
628d791 hotplug: reliably handle interfaces with ubus zone hints
d005293 fw4: store zone associations from ubus in statefile as well
b268225 fw4: filter non hw-offload capable devices when resolving lower devices
57984e0 fw4: always resolve lower flowtable devices
7782017 tests: fix mocked `fd.read("line")` api
72b196d config: remove restictions on DHCPv6 allow rule
f0cc317 fw4: refactor family selection for forwarding rules
b0b8122 treewide: use modern syntax
05995f1 fw4: fix emitting device jump rules for family restricted zones
b479815 fw4: fix family auto-selection for config nat rules
2816a82 ruleset: ensure that family-agnostic ICMP rules cover ICMPv6 as well
2379c3d tests: add test coverage for zone family selection logic
Fixes: #5066, #9611, #9765, #9854
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly,
there is noneed to include package and ship them like we do now.
This also resolves the performance issues that happen as MikroTik
changes the boards and ships them under the same revision but they
actually ship with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some ath10k IPQ40xx devices like the MikroTik hAP ac2 and ac3 require the
BDF-s to be extracted from the device storage instead of shipping packaged
API 2 BDF-s.
This is required as MikroTik has started shipping boards that require BDF-s
to be updated, as otherwise their WLAN performance really suffers.
This is however impossible as the devices that require this are release under
the same revision and its not possible to differentiate them from devices
using the older BDF-s.
In OpenWrt we are extracting the calibration data during runtime and we are
able to extract the BDF-s in the same manner, however we cannot package the
BDF-s to API 2 format on the fly and can only use API 1 to provide BDF-s on
the fly.
This is an issue as the ath10k driver explicitly looks only for the board.bin
file and not for something like board-bus-device.bin like it does for pre-cal
data.
Due to this we have no way of providing correct BDF-s on the fly, so lets
extend the ath10k driver to first look for BDF-s in the board-bus-device.bin
format, for example: board-ahb-a800000.wifi.bin
If that fails, look for the default board file name as defined previously.
So, backport the upstream ath10k patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update ath10k-ct to the latest version which includes the backported
ath10k commit for requesting API 1 BDF-s with a unique name like caldata.
Signed-off-by: Robert Marko <robimarko@gmail.com>
