Instead of vaguely describing dependencies in the package description
actually split-up into individual packages, each with their
dependencies expressed accurately.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Split utility packages similar to coreutils in packages feed, adding
ALTERNATIVES for those which are also provided by busybox-selinux.
Also add missing license information.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When the nulldata frame was acked, the probe send count needs to be reset,
otherwise it will keep increasing until the connection is considered dead,
even though it fine.
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The required BusyBox applets are enabled by default, so we can rely on them
being present in the system. This way, we make sure there are no conflicts
with less featured variants of these same applets which might also be
present in the system.
Fixes: 0bd7dfa3ed ("zram-swap: enable swap discard")
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[wrap commit description]
Signed-off-by: David Bauer <mail@david-bauer.net>
Some 5GHz wifi interfaces, especially in Tri-band routers, can't use
channel 36. In these cases, the default configuration for 5GHz
interfaces, once enabled, doesn't work.
This patch selects the first non-disabled channel for 5GHz interfaces.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
We want to be able to make full system images for this system too, just
as we now can for the MT7623 platforms.
The package directory (mt7623n) is now a bit misnamed as it's overly
specific, but the precise set of platforms which we support this way
is evolving and we'll fix it up when the dust settles and we know what
nomenclature makes most sense.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Update to current head of the branch A3700_utils-armada-18.12-fixed:
0967979 ddr: Add DDR3 2CS layout for EspressoBin v5 2GB board
486523e ddr: fix typo for ESPRESSObin 2GB layout
490b2b3 TBB: Fix building for Crypto++ 6.0 and later
0141dd1 TBB: Split INCDIR from LIBDIR
Signed-off-by: Andre Heider <a.heider@gmail.com>
Lift the dependency on the build order, where flash-image.bin may be missing
from the u-boot dir.
While at it, also install the uart images for rescue purposes.
Signed-off-by: Andre Heider <a.heider@gmail.com>
With global NLS support enabled (CONFIG_BUILD_NLS), the linked libelf.so
and libbfd.so libraries will depend on libintl.so. Import the nls.mk helper
to set library prefixes and flags accordingly, and also conditionally add
"-lintl" as link-time library.
Fix a build error on ppc due to a EDEADLOCK redefinition in errno.h.
Use upstream stable kernel 5.8.9, and fix overriding of feature detection
to only allow/hide detected features. Also refresh existing patches.
Fixes: 2f0d672088 ("bpftools: add utility and library packages supporting
eBPF usage")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
amd64-microcode (3.20191218.1)
* New microcode update packages from AMD upstream:
+ Removed Microcode updates (known to cause issues):
sig 0x00830f10, patch id 0x08301025, 2019-07-11
* README: update for new release
amd64-microcode (3.20191021.1)
* New microcode update packages from AMD upstream:
+ New Microcodes:
sig 0x00830f10, patch id 0x08301025, 2019-07-11
+ Updated Microcodes:
sig 0x00800f12, patch id 0x08001250, 2019-04-16
sig 0x00800f82, patch id 0x0800820d, 2019-04-16
amd64-microcode (3.20181128.1)
* New microcode update packages from AMD upstream:
+ New Microcodes:
sig 0x00800f82, patch id 0x0800820b, 2018-06-20
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
CONFIG_BMP085* is replaced by CONFIG_BMP280 since 4.9[1] and this package is empty.
OpenWRT also has kmod-iio-bmp280* package and we can drop old packages.
1. [ misc: retire the old BMP085 driver ]
(832c8232dd (diff-5000d544d790c669405eb2a6775e5981))
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
3b946a6dc588 mt76: dma: cache dma map address/len in struct mt76_queue_entry
c4c8b6a20d3b mt76: mt7915: fix HE BSS info
15391c1c947f mt76: fix tx hang on non-AQL frame limit
72c8a81e64e8 mt76: mt7915: fix encap offload multicast traffic with 4-address mode
69b3f868d14b mt76: mt7915: use napi_consume_skb to bulk-free tx skbs
5f080033ec7d mt76: move txwi handling code to dma.c, since it is mmio specific
b1f425686125 mt76: mt7915: fix VHT LDPC capability
8f48855f5d14 mt76: mt7915: simplify mt7915_lmac_mapping
cfaf40858718 mt76: mt7915: fix queue/tid mapping for airtime reporting
115b62efac21 mt76: remove retry_q from struct mt76_txq and related code
e22c65cdc585 mt76: mt7915: simplify checks for the 802.3 offload path
bab866a01e4f mt76: mt7915: fix unexpected firmware mode
0fc3c5eb61d0 mt76: dma: queue more rx frames internally before passing them to the stack
130e5de09364 Revert "mt76: dma: queue more rx frames internally before passing them to the stack"
e3af31409d41 update mt7915 firmware to the latest version
e2b8a4ec9891 mt76: testmode: add a limit for queued tx_frames packets
146488631f7b mt76: mt7615: Remove set but unused variable 'index'
0b7d2b76288e mt76: mt7615: fix VHT LDPC capability
848f4a6334a8 mt76: mt7622: fix fw hang on mt7622
0a955d944bd0 mt76: mt7663s: do not use altx for ctl/mgmt traffic
13b96411513b mt76: mt7663s: split mt7663s_tx_update_sched in mt7663s_tx_{pick,update}_quota
d62ba15b1bbf mt76: mt7663s: introduce __mt7663s_xmit_queue routine
fdf14d1b6aec mt76: move pad estimation out of mt76_skb_adjust_pad
d048f8e87ba0 mt76: mt7663s: fix possible quota leak in mt7663s_refill_sched_quota
979c0fdc5d27 mt76: mt7663s: introduce sdio tx aggregation
56e77a3a3ade mt76: mt7663: check isr read return value in mt7663s_rx_work
f96cffa03e57 mt76: mt7615: unlock dfs bands
1ccd31bbe1f4 mt76: Use fallthrough pseudo-keyword
448cd2d36ee2 mt76: mt76x0: Move tables used only by init.c to their own header file
17ba3432f5af Revert "mt76: mt7615: unlock dfs bands"
fee1f4a8e87f mt76: mt7915: fix possible memory leak in mt7915_mcu_add_beacon
5b78e5292777 mt76: Fix unsigned expressions compared with zero
ec84891a4d23 mt76: mt7915: convert to use le16_add_cpu()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is the most popular choice in the linux kernel tree.
Within OpenWrt, this change will establish consistency with ath79
and ramips targets.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Drop patches as they've been upstreamed:
* 001-Fix-CVE-2020-12762.patch
Refresh patches:
* 000-libm.patch
Add patch to avoid build failure due to missing docs in tarball.
Signed-off-by: David Bauer <mail@david-bauer.net>
On devices with small amounts of RAM, zram-swap fails to initialise due to the
default compression algorithm (lzo-rle). Startup example on an AirGrid M2, with
32 MiB of RAM:
root@airgrid:/etc/config# /etc/init.d/zram start
zram_start: activating '/dev/zram0' for swapping (13 MegaBytes)
zram_reset: enforcing defaults via /sys/block/zram0/reset
sh: write error: Out of memory
mkswap: image is too small
swapon: /dev/zram0: Invalid argument
root@airgrid:/etc/config#
Fix this by defaulting to traditional lzo, which works fine and is always
available.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
- tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
- ubiattach -p /dev/mtd0
- ubirmvol /dev/ubi0 -n0
- ubirmvol /dev/ubi0 -n1
- ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
- sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for the Edgecore ECW5211 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This patch adds support for the Edgecore ECW5410 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.
Installation instructions:
Through stock firmware or initramfs.
1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>
This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0
Note
Initramfs:
1. Connect to console
2. Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1
You need to interrupt the bootloader after rebooting and run:
run altbootcmd
This will switch your active rootfs partition to one you wrote to and boot from it.
So if rootfs1 is active, then it will change it to rootfs2.
This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.
5. Transfer sysupgrade image
6. Flash with sysupgrade -n.
Note that sysupgrade will write the image to rootfs partition that is not currently in use.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This enables the ipq-wifi package to be used on IPQ806x target.
Its needed for boards using a different BDF than one shipped in the upstream board-2.bin.
Currently needed for Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
vconfig has been disabled by default since 2015 [1] and there are
no remaining uses in entire OpenWrt trunk. However, we still set up
a specific name_type for it during boot.
While this setup is properly implemented to be only triggered when
vconfig is present, it still seems anachronistic and unnecessary
to set up a standard for a tool that is not used anymore.
Therefore, this removes the set_name_type initialization and leaves
it for those people actually using the tool to configure it as needed.
[1] 899a23227e ("busybox: improve applets & deprecate ifconfig, route")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target has not been updated to 5.4 yet, and the only person
trying it (Koen) decided to retreat based on the following reasons:
- The target is not DT-aware at all
- The huge amount of effort required
- The SoC itself reached EoL at Cavium for some time now
- Upstream removed some important parts as it's also slowly getting EoL
over there
- The commercial product that used this will fade out shortly
- The amount of download for this binary suggest that the target is not
that popular
Since nobody has picked up the work since then, and this is the last
remaining 4.19-only target, finally drop it now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On the Turris Omnia 2019, u-boot environment is located at 0xF0000, instead
of 0xC0000. The switch happened with u-boot-omnia package version 2019-04-2
(May 10, 2019).
Check the installed u-boot release, and set the default accordingly.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
[bump PKG_RELEASE, use lower case for hex offset]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for per-BSS airtime weight configuration. This allows to set
a airtime weight per BSS as well as a ratio limit based on the weight.
Support for this feature is only enabled in the full flavors of hostapd.
Consult the hostapd.conf documentation (Airtime policy configuration)
for more information on the inner workings of the exposed settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the default state for LEDs to off. When a trigger is set, the
trigger will turn the LED automatically on.
Currently LEDs might stay on, e.g. when the LED trigger is set to a
netdev trigger and the interface is never activated or the 'none'
trigger is selected without setting the 'default' option to 0 and it's
set for the LED indicating the system running state.
Using off as a default value is also consistent with the documentation
in the OpenWrt wiki.
Signed-off-by: David Bauer <mail@david-bauer.net>
TITLE is "NFS4 filesystem client support" (Line 428)
but the description is "Kernel module for NFS v4 support" (Line 438).
Use "Kernel module for NFS v4 client support" on line 438.
Signed-off-by: Bob Cai <1119283622@qq.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipc: split into separate files per-platform
This is in preparation for FreeBSD support, which I had hoped to have this
release, but we're still waiting on some tooling fixes, so hopefully next
wg(8) will support that. Either way, the code base is now a lot more amenable
to adding more kernel platform support.
* man: wg-quick: use syncconf instead of addconf for strip example
Simple documentation fix.
* pubkey: isblank is a subset of isspace
* ctype: use non-locale-specific ctype.h
In addition to ensuring that isalpha() and such isn't locale-specific, we also
make these constant time, even though we're never distinguishing between bits
of a secret using them. From that perspective, though, this is markedly better
than the locale-specific table lookups in glibc, even though base64 characters
span two cache lines and valid private keys must hit both. This may be useful
for other projects too: https://git.zx2c4.com/wireguard-tools/tree/src/ctype.h
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Don't use bash syntax, because /bin/sh is used here.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Minor cleanup and code reorganization, along with a change to not disable
offload anymore when a tkip or sw crypto key is added
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* compat: backport kfree_sensitive and switch to it
* netlink: consistently use NLA_POLICY_EXACT_LEN()
* netlink: consistently use NLA_POLICY_MIN_LEN()
* compat: backport NLA policy macros
Backports from upstream changes.
* peerlookup: take lock before checking hash in replace operation
A fix for a race condition caught by syzkaller.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
3d9bd73 utils: fix check_pid_path to work with deleted file as well
330f403 vlan: initialize device ifname earlier at creation time
c057e71 device: do not check state from within device_init
cb0c07b system-dummy: fix resolving ifindex
ccd9ddc bridge: add support for turning on vlan_filtering
82bcb64 bridge: add support for adding vlans to a bridge
0e8cea0 bridge: add support for VLAN filtering
6086b63 config: enable bridge vlan filtering by default for bridges that define VLANs
ac0710b device: look up full device name before traversing vlan chain
e32e21e bridge: flush vlan list on bridge free
645ceed interface-ip: clear host bits of the device prefix
d7b614a netifd-wireless: parse 'osen' encryption
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
