Commit Graph

5 Commits

Author SHA1 Message Date
Adrian Schmutzler
41cc7edc15 ath79: move dts-v1 statement to ath79.dtsi
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.

Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 23:26:34 +02:00
Adrian Schmutzler
a967ae9d14 ath79: remove redundant includes in DTS files
Many DTS files contain the same includes again that are already
present in the DTSI files they are derived from.

Remove those redundant includes in the DTS files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-22 19:17:51 +01:00
Adrian Schmutzler
6c407fb5db ath79: do not set inherited phy-mode/status properties again
There are several cases where phy-mode and status properties are
set again in DTS(I) files although those were set to the same values
in parent DTSI files already. Remove those cases (and thus also stop
their proliferation by copy/paste).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 13:42:12 +01:00
Adrian Schmutzler
c8190713cb ath79: harmonize ethernet-phy naming scheme
A minority of ethernet-phy definitions seems to use numbers in label,
name and reg property relatively random. This patch aligns their
use to have the same numeric value for all of them.

While at it, improve order of properties/add newlines for the ethX
nodes where necessary.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 13:40:59 +01:00
Petr Štetiar
40530c8eb4 ath79: Add support for Ubiquiti Nanostation M (XW)
CPU:  AR9342 SoC
RAM:      64 MB DDR2
Flash:     8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN:  2.4/5 GHz
UART:      1 UART
LEDs:        Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:     Reset

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-05 03:15:52 +01:00