It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds.
Investigation shows that the board failed to adapt the ethernet pll values as shown here:
[ 5.284359] ag71xx 19000000.eth: failed to read pll-handle property
added custom prints in code and triggering a link switch:
[ 62.821446] Atheros AG71xx: fast reset
[ 62.826442] Atheros AG71xx: update pll 2
[ 62.830494] Atheros AG71xx: no pll regmap!
Comparison with another very similar board (rb922 - QCA955x) showed a missing
reference clock frequency in dts, which seems to cause a pll init issue.
Unfortunately, no errors are printed when this occurs.
Adding the frequency property fixes the pll init as it can be parsed now
by the ethernet driver.
[ 55.861407] Atheros AG71xx: fast reset
[ 55.866403] Atheros AG71xx: update pll 2
[ 55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ 10/100 Mbps Ethernet
+ builtin switch port 1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Asus RP-AC66 Repeater
Hardware specifications:
Board: AP152
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 25l128 16MB SPI-NOR
LAN/WAN: 1x1000M QCA8033
WiFi 5GHz: QCA9880
Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
MAC addresses as verified by OEM firmware:
use address source
Lan/Wan *:24 art 0x1002 (label)
2G *:24 art 0x1002
5G *:26 art 0x5006
Installation:
Asus windows recovery tool:
- install the Asus firmware restoration utility
- unplug the router, hold the reset button while powering it on
- release when the power LED flashes slowly
- specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
- Start the Asus firmware restoration utility, specify the factory image
and press upload
- Do not power off the device after OpenWrt has booted until the LED flashing.
TFTP Recovery method:
- set computer to a static ip, 192.168.1.75
- connect computer to the LAN 1 port of the router
- hold the reset button while powering on the router for a few seconds
- send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
On startup the USB of QCA9531 board can't be initialized successfully.
lsusb result as below:
root@OpenWrt:~# lsusb unable to initialize libusb: -99
This is because usb-phy-analog is not added to reset list.
Signed-off-by: Jinfan Lei <153869379@qq.com>
(added linebreaks and small little changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
mtd: spi-nor: locking support for MX25L6405D
Macronix MX25L6405D supports locking with four block-protection bits.
Currently, the driver only sets three bits. If the bootloader does not
sustain the flash chip in an unlocked state, the flash might be
non-writeable. Add the corresponding flag to enable locking support with
four bits in the status register.
mtd: spi-nor: disable 16-bit-sr for macronix
Macronix flash chips seem to consist of only one status register.
These chips will not work with the "16-bit Write Status (01h) Command".
Disable SNOR_F_HAS_16BIT_SR for all Macronix chips.
Refreshed:
- 0052-mtd-spi-nor-use-4-bit-locking-for-MX25L12805D.patch
Fixes: 15aa53d7ee ("ath79: switch to Kernel 5.10")
Signed-off-by: Nick Hainke <vincent@systemli.org>
The UBNT_REVISION was already added for the ubnt-xw target because:
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails
...
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again.
commit d42a7c4699 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method")
Fixes errors in the form of (tftp flashing):
sent DATA <block=8577, 412 bytes>
received ERROR <code=2, msg=Firmware check failed>
Error code 2: Firmware check failed
The missing UBNT_REVISION was not noticed before, since the
UBNT_REVISION field for the ubnt-xm target was also set to:
"42.OpenWrt-..."
Probably, UBNT_REVISION for the ubnt-xm target was set by the ubnt-xw
and was never overridden somewhere else. However, it is missing and
should be part of the ubnt-xm device.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Kernel 5.10 is used by many people since quite a while. With other
targets already moved to 5.10, let ath79 follow suit.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> [ath79/tl-wdr4300]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
ar9344_openmesh_mr600-v1.dts:40.10-44.5: Warning (gpios_property):
/leds-ath9k/wifi2g: Missing property '#gpio-cells' in node
/ahb/pcie-controller@180c0000/wifi@0,0 or bad phandle
=> added gpio-controller + #gpio-cells
qca955x_zyxel_nbg6x16.dtsi:121.3-13: Warning (reg_format):
/ahb/usb@1b000000/port@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
../dts/qca955x_zyxel_nbg6x16.dtsi:131.3-13: Warning (reg_format):
/ahb/usb@1b400000/port@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
qca955x_zyxel_nbg6x16.dtsi:120.20-123.4: Warning (avoid_default_addr_size):
/ahb/usb@1b000000/port@1: Relying on default #address-cells value
=> ath79's usb-nodes are missing the address- and size-cells properties.
These are needed for usb led trigger support.
ar7242_ubnt_sw.dtsi:54.4-14: Warning (reg_format): /gpio_spi/gpio_spi@0:reg:
property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
=> the #address-cells and #size-cells had to be nudged.
qca9531_dlink_dch-g020-a1.dts:19.6-39.4: Warning (i2c_bus_bridge):
/i2c: incorrect #size-cells for I2C bus
=> #size-cells = <0>;
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SoC: AR9344
RAM: 128MB
Flash: 16MiB SPI NOR
5GHz WiFi: AR9382 PCIe 2x2:2 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n
5x Fast ethernet via SoC switch (green LEDs)
1x USB 2.0
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO
UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX
Flash factory image via "emergency room" recovery:
- Configure your computer with a static IP 192.168.1.123/24
- Connect to LAN port on the N600 switch
- Hold reset putton
- Power on, holding reset until the power LED blinks slowly
- Visit http://192.168.1.1/ and upload OpenWrt factory image
- Wait at least 5 minutes for flashing, reboot and key generation
- Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
[dt leds preparations]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The jjPlus JWAP230 is an access point board built around the QCA9558,
with built-in 2.4GHz 3x3 N WiFi (28dBm). It can be expanded with 2
mini-PCIe boards, and has an USB2 root port.
Specifications:
- SOC: Qualcomm Atheros QCA9558
- CPU: 720MHz
- H/W switch: QCA8327 rev 2
- Flash: 16 MiB SPI NOR (en25qh128)
- RAM: 128 MiB DDR2
- WLAN: AR9550 built-in SoC bgn 3T3R (ath9k)
- PCI: 2x mini-PCIe (optional 5V)
- LEDs: 6x LEDs (3 are currently available)
- Button: 1x Reset (not yet defined)
- USB2:
- 1x Type A root port
- 1x combined mini-PCIe
- Ethernet:
- 2x 10/100/1000 (1x PoE 802.3af (36-57 V))
Notes:
The device used to be supported in the ar71xx target.
For upgrades: Please use "sysupgrade --force -n <image>".
This will restore the device back to OpenWrt defaults!
MAC address assignment:
use source
LAN art 0x0
WAN art 0x6
WLAN art 0x1002 (as part of the calibration data)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftp 0x80060000 \
openwrt-ath79-generic-jjplus_jwap230-squashfs-sysupgrade.bin
> erase 0x9f050000 +${filesize}
> cp.b $fileaddr 0x9f050000 $filesize
> setenv bootcmd bootm 0x9f050000
> saveenv
Signed-off-by: Olivier Valentin <valentio@free.fr>
[Added DT-Leds (based on ar71xx), Added more notes about sysupgrade,
fixed "qca9550" to match SoC in commit and dts file name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
TP-Link EAP225 v1 is an AC1200 (802.11ac Wave-1) ceiling mount access point.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9882): a/n/ac, 2x2
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* Ensure the device is upgraded to firmware v1.4.0
* Exploit the user management page in the web interface to start telnetd
by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
(e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
patch listed below. The patch is required to prevent `uclited -u` in
the last step from crashing.
* Copy the patched uclited binary back to the device at /tmp/uclited
(via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.
uclited patching:
--- xxd uclited
+++ xxd uclited-patched
@@ -53811,7 +53811,7 @@
000d2330: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... ..........
000d2340: 8fa6 0a4c 02c0 2821 8f82 87c4 0000 0000 ...L..(!........
-000d2350: 8c44 0000 0c13 461c 27a7 0018 8fbc 0010 .D....F.'.......
+000d2350: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$...........
000d2360: 1040 001d 0000 1821 8f99 8378 3c04 0058 .@.....!...x<..X
000d2370: 3c05 0056 2484 ad68 24a5 9f00 0320 f809 <..V$..h$.... ..
To make sure the correct file is patched, the following MD5 checksums
should match the unpatched and patched files:
4bd74183c23859c897ed77e8566b84de uclited
4107104024a2e0aeaf6395ed30adccae uclited-patched
Debricking:
* Serial port can be soldered on unpopulated 4-pin header
(1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors running from pins 1 (TXD) and 2 (RXD).
Do NOT bridge the pull-down for pin 2, running parallel to the
header.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
Tested by forum user KernelMaker.
Link: https://forum.openwrt.org/t/eap225-v1-firmware/87116
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add the Embedded Wireless "Balin" platform, it is in ar71xx too
SoC: QCA AR9344 or AR9350
RAM: DDR2-RAM 64MBytes
Flash: SPI-NOR 16MBytes
WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
Ethernet: 3 x 10/100 Mb/s
USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
PCIe: MiniPCIe - 1 x lane PCIe 1.2
Button: 1 x Reset-Button
UART: 1 x Normal, 1 x High-Speed
JTAG: 1 x EJTAG
LED: 1 x Green Power/Status LED
GPIO: 10 x Input/Output multiplexed
The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade -n --force <image>" image directly in
vendor firmware. This resets the existing configurations back to
default!
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
[indent, led function+color properties, fix partition unit-address,
re-enable pcie port, mention button+led in commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
For v2, both ath9k (2.4GHz Wifi) and ath10k (5 GHz) driver now
pull the (pre-)calibration data from the nvmem subsystem. v1
is slightly different as only the ath9k Wifi is supported.
This allows us to move the userspace caldata extraction
and mac-address patching for the 5GHZ ath10k supported
wifi into the device-tree definition of the device.
ath9k's nodes are also changed over to use nvmem-cells
over OpenWrt's custom mtd-cal-data property.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Further devices from the series have been added in the meantime,
introducing `qca955x_dlink_dap-2xxx.dtsi`.
Thus, merge support for DAP-2695 with the existing dtsi.
This implies factory images can now be flashed via the regular
OEM Web UI, as well as the bootloader recovery.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This device can be merged with the existing dtsi, which declares
the location of ath9k cal-data via devicetree, correcting the 2.4G
mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`.
To make these changes more visible, apply before merging with dtsi.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This device can be merged with the existing dtsi,
which will increase spi-max-frequency to 50 MHz.
To make this change more visible, increase to 50 MHz before merging.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and
RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi
integrated antenna built around the Atheros AR9344 SoC.
It is very similar to the SXT Lite5 series which this patch is based
upon.
Specifications:
- SoC: Atheros AR9344
- RAM: 64 MB
- Storage: 16 MB SPI NOR
- Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
- Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
8-32 Vdc PoE in
- 8 user-controllable LEDs:
- 1x power (blue)
- 1x user (white)
- 1x ethernet (green)
- 5x rssi (green)
See https://mikrotik.com/product/RBLHG-5nD for more details.
Notes:
The device was already supported in the ar71xx target.
Flashing:
TFTP boot initramfs image and then perform a sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Jakob (Jack/XDjackieXD) <jakob@chaosfield.at>
The MikroTik RouterBOARD wAPR-2nD (wAP R) router features a miniPCI-e
slot with USB lines connected, which are used by some USB cards with
miniPCI-e form factor, like the R11e-LR8. Enabling USB support is
required for such cards to work.
Tested on a MikroTik wAP LR8 kit (RB wAPR-2nD + R11e-LR8).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
converts the still popular WNDR3700 Series to fetch the
caldata through nvmem. As the "MAC with NVMEM" has shown,
there could pitfalls along the way.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Netgear R6100 is a dual-band Wi-Fi 5 (AC1200) router based on Qualcomm
Atheros (AR9344 + QCA9882) platform. Support for this device was first
introduced in 15f6f67d18 (ar71xx). FCC ID: PY312400225.
Specifications:
- Atheros AR9344 (560 MHz)
- 128 MB of RAM (DDR2)
- 128 MB of flash (parallel NAND)
- 2T2R 2.4 GHz Wi-Fi (AR9344)
- 2T2R 5 GHz Wi-Fi (QCA9882)
- 5x 10/100 Mbps Ethernet (AR9344)
- 4x internal antenna
- 1x USB 2.0 (GPIO-controlled power)
- 6x LED, 3x button (reset, Wi-Fi, WPS)
- UART (4-pin, 2.54 mm pitch) header on PCB
- 1x mechanical power switch
- DC jack for main power input (12 V)
WARNING: sysupgrade from older stable releases is not possible, fresh
installation (via vendor's GUI or TFTP based recovery) is required.
Reason for that is increased kernel partition size.
Installation:
Use the 'factory' image under vendor's GUI or via TFTP U-Boot recovery.
You can use the 'nmrpflash' tool at a boot time, before kernel is loaded
or start it manually by pressing the 'reset' button for ~20 seconds from
powering up the device (U-Boot will start TFTP server on 192.168.1.1,
use TFTP client to send the image).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GPIOs on the Aircube AC are wrong:
- Reset GPIO moved from 17 to 12
- PoE Pass Through GPIO for Aircube AC is 3
Fixes: 491ae3357e ("ath79: add support for Ubiquiti airCube AC")
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Specifications:
SOC: QCA9531 650 MHz
ROM: 16 MiB Flash (Winbond W25Q128FV)
RAM: 128 MiB DDR2 (Winbond W971GG6SB)
LAN: 10/100M *2
WAN: 10/100M *1
LED: BGR color *1
Mac address:
label C8:0E:77:xx:xx:68 art@0x0
lan C8:0E:77:xx:xx:62 art@0x6
wan C8:0E:77:xx:xx:68 art@0x0 (same as the label)
wlan C8:0E:77:xx:xx:B2 art@0x1002 (load automatically)
TFTP installation:
* Set local IP to 192.168.67.100 and open tftpd64, link lan
port to computer.
Rename "xxxx-factory.bin" to
"openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin".
* Make sure firmware file is in the tftpd's directory, push
reset button and plug in, hold it for 5 seconds, and then
it will download firmware from tftp server automatically.
More information:
* This device boot from flash@0xe80000 so we need a okli
loader to deal with small kernel partition issue. In order
to make full use of the storage space, connect a part of the
previous kernel partition to the firmware.
Stock Modify
0x000000-0x040000(u-boot) 0x000000-0x040000(u-boot)
0x040000-0x050000(u-boot-env) 0x000000-0x050000(u-boot-env)
0x050000-0xe80000(rootfs) 0x050000-0xe80000(firmware part1)
0xe80000-0xff0000(kernel) 0xe80000-0xe90000(okli-loader)
0xe90000-0xff0000(firmware part2)
0xff0000-0x1000000(art) 0xff0000-0x1000000(art)
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
This changes the image generation to use a unique directory. With
parallel building it may occur that two concurrent jobs try
to create an image which leds to errors. It also removes a needless
subdirecory.
Signed-off-by: André Valentin <avalentin@marcant.net>
This patch enables the SFP cage on the MikroTik RouterBOARD 921GS-5HPacD
(mANTBox 15s).
The RB922UAGS-5HPacD had it already working, so the support code is
moved to the common DTSI file both devices share.
Tested on a RouterBOARD 921GS-5HPacD with a MikroTik S-53LC20D module.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
OpenWrt maintains two special out-of-tree DT properties:
"qca,disable-5ghz" and "qca,disable-2ghz". These are implemented
in a mac80211 ath9k patch "550-ath9k-disable-bands-via-dt.patch".
With the things being what they are, now might be a good
point to switch the devices to the generic and upstream
"ieee80211-freq-limit" property. This property is much
broader and works differently. Instead of disabling the
drivers logic which would add the affected band and
channels. It now disables all channels which are not
within the specified frequency range.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # HH5A
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ag71xx_probe is registering ag71xx_interrupt as handler for the gmac0/gmac1
interrupts. The handler is trying to use napi_schedule to handle the
processing of packets. But the netif_napi_add for this device is
called a lot later in ag71xx_probe.
It can therefore happen that a still running gmac0/gmac1 is triggering the
interrupt handler with a bit from AG71XX_INT_POLL set in
AG71XX_REG_INT_STATUS. The handler will then call napi_schedule and the
napi code will crash the system because the ag->napi is not yet
initialized:
libphy: Fixed MDIO Bus: probed
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 00000000, ra == 81373408
Oops[#1]:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.152 #0
$ 0 : 00000000 00000001 00000000 8280bf28
$ 4 : 82a98cb0 00000000 81620000 00200140
$ 8 : 00000000 00000000 74657272 7570743a
$12 : 0000005b 8280bdb9 ffffffff ffffffff
$16 : 00000001 82a98cb0 00000000 8280bf27
$20 : 8280bf28 81620000 ffff8b00 8280bf30
$24 : 00000000 8125af9c
$28 : 82828000 8280bed8 81610000 81373408
Hi : 00005fff
Lo : 2e48f657
epc : 00000000 0x0
ra : 81373408 __napi_poll+0x3c/0x11c
Status: 1100dc03 KERNEL EXL IE
Cause : 00800008 (ExcCode 02)
BadVA : 00000000
PrId : 00019750 (MIPS 74Kc)
Modules linked in:
Process swapper (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : ffff8afb ffff8afa 81620000 00200140 00000000 82a98cb0 00000008 0000012c
81625620 81373684 ffffffff ffffffff ffffffef 00000008 816153d8 81620000
815b0d60 815bbd54 00000000 81753700 8280bf28 8280bf28 8280bf30 8280bf30
81753748 00000008 00000003 00000004 0000000c 00000100 3fffffff 8175373c
816059f0 814ddb48 00000001 8160ab30 81615488 810618bc 00000006 00000000
...
Call Trace:
[<81373684>] net_rx_action+0xfc/0x26c
[<814ddb48>] __do_softirq+0x118/0x2ec
[<810618bc>] handle_percpu_irq+0x50/0x80
[<8125ab8c>] plat_irq_dispatch+0x94/0xc8
[<81004e98>] handle_int+0x138/0x144
Code: (Bad address in epc)
---[ end trace a60d797432b656b2 ]---
The gmcc0/gmac1 must be brought in a state in which it doesn't signal a
AG71XX_INT_POLL related status bits as interrupt before registering the
interrupt handler. ag71xx_hw_start will take care of re-initializing the
AG71XX_REG_INT_ENABLE.
Fixes: f529a37420 ("surprise :p")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Back in the AR71XX days, the lzma-loader code could be customized
based on the $BOARD variable. These would be passed as a
compile-time -DCONFIG_BOARD_$DEVICE_MODEL flag to the compiler.
Hence, the lzma-loader would be able to include device-specific
fixups.
Note: There's still a fixup for the TpLink TL-WR1043ND V1 found
in the lzma-loader's board.c code. But since the days of AR71XX
I couldn't find a forum post or bug reported. So, I left it
as is to not break anything by enabling it.
=> If you have a TL-WR1043ND V1 and you have problem with
the ethernet: let me know. Because otherwise, the fixup
might simply no longer needed with ath79 and it can be removed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default
symbols for the ath79/mikrotik target.
MikroTik devices hold some of their user-configurable settings in the
soft_config partition, which is typically sized 4 KiB, of the SPI NOR
flash memory. Previously, in the ar71xx target, it was possible to use
64 KiB erase sectors but also smaller 4 KiB ones when needed. This is
no longer the case in ath79 with newer kernels so, to be able to write
to these 4 KiB small partitions without erasing 60 KiB around, the
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults.
However, this ended up making sysupgrade images which were built with
64 KiB size blocks not to keep settings (e.g., the files under
/etc/config/) over the flashing process.
Using 4 KiB erase sector size on the sysupgrade images (by setting
BLOCKSIZE = 4k) allows keeping settings over a flashing process, but
renders the process terribly slow, possibly causing a user to
mistakenly force a manual device reboot while the process is still on-
going. Instead, ditching the 4 KiB erase sectors for the default
64 KiB erase size provides normal SPI write speed and sysupgrade times,
at the expense of not being able to modify the soft_config partition
(which is rarely a required thing).
An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have
allowed to use different per-partition erase sector sizes. Due to
changes on recent kernels it now only works on a per-device basis.
Also, partial eraseblock write can be performed in ath79 with kernels
5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole
sector and restoring those blocks not meant to be modified. A kernel
bump had that patch broken for a long time, but got fixed in bf2870c.
Note: the settings in the soft_config partition can be reset to their
defaults by holding the reset button for 5 seconds (and less than 10
seconds) at device boot.
Fixes: FS#3492 (sysupgrade […] loses settings...)
Fixes: a66eee6336 (ath79: add mikrotik subtarget)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
AR9331 requires kmod-usb2-chipidea to use the USB ports. Include the
correct package so they can be used with the base image.
Signed-off-by: David Bauer <mail@david-bauer.net>
These instructions are repeated for a few devices now, let's move
them to shared definition so we do not repeat ourselves too often.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on the AP152 reference board
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate) Based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal
reflector
- Power, LAN, WLAN5G Blue LEDs
- 3x Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[convert to nvmem, fix MAC assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
