Use NVMEM "calibration" implementation for ath9k/ath10k(-ct) on ELECOM
WRC-300GHBK2-I and WRC-1750GHBK2-I/C instead of mtd-cal-data property
or user-space script.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use ARTIFACTS to generate factory image of the following ELECOM devices
instead of redundant recipe which generate on KERNEL_INITRAMFS.
- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use from the following devices in ath79 target, move edimax-header to
image-commands.mk.
- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Set 5.15 as default kernel. Testing support was already added on
29.03.2021.
Testing support was added in
9b3bc5d119 ("x86: enable 5.15 as testing kernel").
[0] - edd6021465
Tested-by: Mark Mentovai <mark@mentovai.com>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Don't reply on mapped rootfs partition but rather just take what ever
has been set to the kernel cmdline root= parameter as a hint to decide
which media to install sysupgrade to on the BananaPi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* remove orphaned Kconfig symbol now that CONFIG_IIO is no longer
selected after commit ef8b935c95 ("mediatek: clean up mt7622 kernel config")
* select UBI fast-map feature to decrease boot time and keep the
number of spare blocks required in sync with U-Boot's expectations
(we got fast-map enabled in U-Boot)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch headers and description for pending patch.
Add version tag to patch already merged upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This gets rid of "nvmem-cells" limitation. Dynamic partitions can be
defined for any (sub)partitions layout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add for mtd-parsers-trx-allow-to-use-on-MediaTek-MIPS-SoCs.patch and
hwmon-lm70-Add-ti-tmp125-support.patch the 5.18 tag as it was merged
in kernel 5.18.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of trying to figure out the actual root device, just use the
kernel 'root' cmdline parameter as a hint to decide which device to
flash to.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use UBI fast map feature to avoid scanning the whole flash on each
boot which takes several seconds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When I enabled CONFIG_HOTPLUG_PCI for mvebu platform, it was asking for
more symbols.
Fixes:
Support for PCI Hotplug (HOTPLUG_PCI) [Y/?] y
CompactPCI Hotplug driver (HOTPLUG_PCI_CPCI) [N/y/?] n
SHPC PCI Hotplug driver (HOTPLUG_PCI_SHPC) [N/y/?] (NEW)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #10645
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Similar to the lzma-loader on our MIPS targets, the spi-loader acts as
a second-stage loader that will then load and start the actual kernel.
As the TL-WDR4900 uses SPI-NOR and the P1010 family does not have support
for memory mapping of this type of flash, this loader needs to contain a
basic driver for the FSL ESPI controller.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport qca8k fixup patches for inband mgmt on Big-Endian systems.
This is needed for ath79 and mpc85xx targets that are Big-Endian and use
qca8k based switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Raising the temperatures for passive and active trips. @VA1DER
proposed at issue 9396 to remove passive trip. This commit relates to
his suggestion.
Without this patch. the CPU will be throttled all the way down to 98MHz
if the temperature rises even a degree above the trip point, and it was
further discovered that if the internal temperature of the device is
above the first trip point temperature when it boots then it will start
in a throttled state and even
$ echo disabled > /sys/class/thermal/thermal_zone0/mode
will have no effect.
The patch increases the passive trip point and active cooling map. The
throttling temperature will then be at 77°C and 82°C, which is still a
low enough temperature for ARM devices to not be in the real danger
zone, and gives some operational headroom.
Signed-off-by: Bruno Umuarama <anonimou_eu@hotmail.com>
The generic imagebuilder does not have a generic in the name, although
this is the default naming scheme. Apply the same fix as for the octeon
target. Thanks to @dangowrt for reporting that the same issues applies
also for the airoha target.
Before the fix:
openwrt-imagebuilder-airoha.Linux-x86_64.tar.xz
After:
openwrt-imagebuilder-airoha-generic.Linux-x86_64.tar.xz
Signed-off-by: Nick Hainke <vincent@systemli.org>
Linksys ea6500-v2 have 256MB of ram. Currently we only use 128MB.
Expand the definition to use all the available RAM.
Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
[ wrap to 80 columns ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream has switched to gnu11 not too long ago. One advantage of
backporting this to these older kernels is, that we can encourage and
write better upstreamable kernels. E.g. the kernel devs prefer loop
declarations. Shrinking the master/local gap will be useful in these
cases.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Christian Marangi <ansuelsmth@gmail.com>
Change GPIO from 10 to 35 to make it works as expected
Fixes: 0de6a3339f ("ipq40xx: Add ZTE MF289F")
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Add multiple patch for krait-cc modernization and multiple fixup for the
driver. Also modify a patch to enable the qsb fixed clock and add pxo to
krait-cc node.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
nand_pins definition is now shipped in ipq8064 dtsi. Rework the
nand_pins definition for wg2600hp3 5.15 files.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch has changed implementation and now the binding has changed.
Replace the old binding with boot-partitions and reimplement the
definition with the new definition.
The new definition is:
<offset1 size1 offset2 size2 offset3 ...>
and now supports sparsed patch.
Also add missing binding in some dts and add the backup boot partition
to the boot-partitions list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove useless spm patch as using the normal qcom,spm compatible is
enough to register it with no clks.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use a new implementation by using a devfreq driver to scale the shared
cache of the krait cpu cores.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport devfreq new cpufreq based PASSIVE governor needed for devfreq
based fab and cache scaling.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reorganize dtsi patches with upstream version and drop dtsi in 5.15
files.
Also add an additional upstream patch for hwspinlock support.
Refresh all the dts with needed changes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This doesn't cause any panic anymore and no regression are observed with
ath10k. Remove this additional patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove qcom adm Documentation patch that is not needed for the target.
Probably a leftover when the adm bus was added, now merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In preparation for a cleanup of 5.15 patches copy the files dir to 5.10
and 5.15 kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The CPU port should define the phy-mode and and a PHY phandle or
fixed-link to indicate how the CPU port is connected to the SoC's
Ethernet controller. On xRX200 this is all internal connection, so use
phy-mode = "internal" along with a fixed-link that matches the
definition inside ð0.
Linux 6.0 shows a warning since upstream commit e09e9873152e3f ("net:
dsa: make phylink-related OF properties mandatory on DSA and CPU
ports"). when these properties are missing. Adding the properties
before OpenWrt is updated to Linux 6.0 is harmless.
Suggested-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This patch converts networking on Sony NCP-HG100/Cellular to DSA and
re-enables support for the device.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Convert ZTE MF289F device to DSA, re-order network ports to match the
labels on the case and re-enable the device.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
* set correct clocks for PWM to work.
* MT7986 PWM does have the 26MHz-clock-select, set that in patch
* drop useless 'passive' trip point in thermal zone
* extend pwm-fan to have 3 active operating points
* set reasonable trip points in thermal zone
* invert pwm-fan operating points and set shorter period to allow
less noisy operation of the PWM fan of the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In *_enable_learning() only address learning should be configured, so
remove enabling forwarding. Forwarding is configured by the respective
*_enable_flood() functions.
Clean up both functions for RTL838x and RTL839x, and fix the comment on
the number of entries.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[squash RTL838x, RTL839x changes]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Those messages should be printed when entry was found (idx >= 0). Move
them to the right place to not print invalid entry indices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amden commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The initial state of sds_mode in rtl9300_force_sds_mode() is null and it
will be configured in switch-case. So print message after it.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Use the generic function of MIPS in Linux Kernel instead of open coding
our own initialisation.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The availabibity of probing CPC depends on CONFIG_MIPS_CPC symbol and it
will be checked in arch/mips/include/asm/mips-cpc.h. RTL9310 selects
this symbol, so the family check is redudant.
Furthermore, mips_cm_probe() is already called from setup_arch() in
mips/kernel/setup.c before prom_init(), and as such is not required.
Also move mips_cpc_probe() to run just before registering SMP ops.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[squash SMP change commits, reword commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
---
This patch only really has an impact on the rtl931x subtarget, which has
no devices. Noboby is currently set up to test these patches either, but
the end result is closer to MIPS_GENERIC, so I do not expect it to cause
issues.
RTL8231 and ethernet phys are not on the same bus, so separate the lock
to each own to cut off the unnecessary dependency.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Everywhere else the device is referred to as WS-AP3805i,
only the model name wrongly only said AP3805i.
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Setup thermal zone, select pins and enabled drivers for I2C (on 26-pin
GPIO bank) and PWM (1x fan and 1x GPIO bank).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for hardware I2C and PWM units found in the Filogic SoCs
as well as the CPU thermal support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows the user to specify a larger tx ring buffer size via ethtool.
Having symmetrical ring buffer sizes increases throughput on high bandwidth
(1 gbps tested) network connections.
The default value is not changed so the same behaviour is saved.
Signed-off-by: Robert Meijer <robert.s.meijer@gmail.com>
[ improve title, commit description and wrap to 80 columns ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert pakedge_wr-1 device to DSA and enable it.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>i
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert luma_wrtq-329acn device to DSA and enable it.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface
corresponding to the non-existing port.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
When testing the DSA changes with 5.15.60 kernel, I've noticed, that the
MAC addresses are not properly configured, there is single MAC being
used for LAN and WAN interfaces:
eth0: 94:83:c4:XX:YY:4a (MAC on sticker)
lan1@eth0: 94:83:c4:XX:YY:4a
lan2@eth0: 94:83:c4:XX:YY:4a
wan@eth0: 94:83:c4:XX:YY:4a
wlan0: 94:83:c4:XX:YY:4a
wlan1: 94:83:c4:XX:YY:4b
The same config, prior to the DSA conversion:
lan/eth0: 94:83:c4:XX:YY:4a (MAC on sticker)
wan/eth1: 94:83:c4:XX:YY:4b
wlan0: 94:83:c4:XX:YY:4a
wlan1: 94:83:c4:XX:YY:4b
Settings in ART partition:
root@OpenWrt:/# hexdump -C /dev/mtd7 | grep '94 83'
00000000 94 83 c4 XX YY 4a 94 83 c4 0e YY 4b ff ff ff ff |.....J.....K....|
00001000 20 2f 8d 8c 01 01 94 83 c4 XX YY 4a 00 00 20 00 | /.........J.. .|
00005000 20 2f 5a 3a 01 01 94 83 c4 XX YY 4b 00 00 20 00 | /Z:.......K.. .|
So let's fix it by keeping same MAC address assigment as was done before
DSA conversion and while at it, define `label-mac-device` as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove networking configs for non DSA converted boards in ipq40xx.
Currently, they are just causing clutter.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Enable threaded NAPI by default in IPQESS driver as it significantly
improves network perfromance, in my testing about 100+ Mbps in WAN-LAN
routing.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This fixes assigning random MAC to br-lan interface upon boot.
While at that, rename at24@50 node to eeprom@50, to align with upstream
device tree style.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Convert IPQ40xx boards to DSA setup.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Signed-off-by: ChunAm See <z1250747241@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Serhii and others have experienced PSGMII link degradation up to point
that it actually does not pass packets at all or packets arrive as zeros.
This usually happened after a couple of hot reboots.
Serhii has managed to track it down to PSGMII calibration not being done
properly and has fixed it, so all of the code is Serhii-s work.
Signed-off-by: Serhii Serhieiev <adron@mstnt.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since kernel 5.4 has been droppped from IPQ40xx, there is no need to keep
the version checks for kernels older than 5.10.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, suspend and resume ops are not present, this means that if user
disables a DSA interface that the PHY-s remain alive and the link is up.
Fix it by using generic PHY suspend and resume ops.
Signed-off-by: Serhii Serhieiev <adron@mstnt.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Select the Ethernet driver, DSA tag driver and the DSA driver itself to
be built in the kernel config.
They automatically pull in switchdev and phylink.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Qualcomm IPQ40xx SoC-s have a variant of QCA8337N switch built-in.
It shares most of the stuff with its external counterpart, however it is
modified for the SoC.
Namely, it doesn't have second CPU port (Port 6), so it has 6 ports
instead of 7.
It also has no built-in PHY-s but rather requires external PSGMII based
companion PHY-s (QCA8072 and QCA8075) for which it first needs to carry
out calibration before using them.
PSGMII has a SoC built-in PHY that is used to connect to the PHY-s which
unfortunately requires some magic values as the datasheet doesnt document
the bits that are being set or the register at all.
Since its built-in it is MMIO like other peripherals and doesn't have its
own MDIO bus but depends on the SoC provided one.
CPU connection is at Port 0 and it uses some kind of a internal connection
and no traditional RGMII/SGMII.
It also doesn't use in-band tagging like other qca8k switches so a shinfo
based tagger is used.
This is based on the current OpenWrt qca8k version that has been imported
from generic target.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This is just importing the qca8k driver from the generic target.
It will be used as the based for IPQ40xx version, this is just
to be able to see the diff.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
PSGMII is a Qualcomm specific mode similar to QSGMII but it has 5 SGMII
lines instead of 4 in QSGMII.
This just adds the support for the PHY layer to be able to identify the
mode for further use.
It is required for the DSA driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQESS is the EDMA replacement driver for the IPQ40xx SoC built-in
ethernet controller.
Unlike EDMA it is Phylink based and doesnt touch PHY-s directly.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
There is no point in using a DT property to trigger setting the PSGMII
PHY AZ transmitting ability.
Especially since EEE can be disabled using ethtool anyway.
Fixup the mask for setting the workaround as only BIT(0) is actually being
changed and use the phy_clear_bits_mmd helper instead of reading, then
clearing the bit and writing back as it does everything for us.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQ40xx requires a special DSA tag driver despite using the QCA8337N
switch.
However they have changed the header format and the existing QCA tag
driver cannot be reused.
For details on how it actually works and else read the patch commit
description.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, QCA807x doesnt do any kind of validation to see whether it
actually supports the inserted module.
So lets add checks to allow only 1000BaseX and 100BaseFX based modules.
While adding validation, move fiber configuration to insert/remove events
instead of always doing it at config time.
This allows getting rid of the DT property for fiber enable and now only
the upstream sfp phandle is required.
Since we are refactoring fiber related code, lets heavily simplify the
status polling as the current logic is overcomplicated due to previous
wish to support non standard SFP cages that dont have pins properly
connected, that is removed now and only proper SFP cages will work.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In order to start working on IPQESS + DSA drop the old ESSEDMA + AR40xx
driver combo.
Remove the kernel symbols, disable swconfig and drop swconfig package
as they are not needed anymore.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This patch is needed to handle interrupts by the second VPE on the Lantiq
ARX100, xRX200, xRX300 and xRX330 SoCs. Switching some ICU interrupts to
the second VPE results in a hang. Currently, the vsmp_init_secondary()
function is responsible for enabling these interrupts. It only enables
Malta-specific interrupts (SW0, SW1, HW4 and HW5).
The MIPS core has 8 interrupts defined. On Lantiq SoCs, hardware
interrupts are wired to an ICU instance. Each VPE has an independent
instance of the ICU. The mapping of the ICU interrupts is shown below:
SW0(IP0) - IPI call,
SW1(IP1) - IPI resched,
HW0(IP2) - ICU 0-31,
HW1(IP3) - ICU 32-63,
HW2(IP4) - ICU 64-95,
HW3(IP5) - ICU 96-127,
HW4(IP6) - ICU 128-159,
HW5(IP7) - timer.
This patch enables all interrupt lines on the second VPE.
This problem affects multithreaded SoCs with a custom interrupt controller.
SOCs with 1004Kc core and newer use the MIPS GIC. At this point, I am aware
that the Realtek RTL839x and RTL930x SoCs may need a similar fix. In the
future, this may be replaced with some generic solution.
Tested on Lantiq xRX200.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
At some point after 21.02.3 and before 22.03.0, the size limits of the
Linksys RE6500 were reached and prevent booting from the 22.03.0 release
or builds of current SNAPSHOT. This patch allows builds of master to boot
again and has been tested on my device.
Fixes: #8577
Signed-off-by: Mark King <mark@vemek.co>
The workaround for an already-enabled R4K timer used a non-existent
macro CAUSE_DC. Fix compiling by using the actual macro CAUSEF_DC.
Fixes: b7aab19585 ("realtek: SMP handling of R4K timer interrupts")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Until now there has been no good explanation why we mess with the R4K
timer on SMP. After extensive testing and looking at the SDK code it
becomes clear what it is all about.
When we disable the CEVT_R4K module (we will do with the new timer
driver) the R4K timer hardware still fires interrupts on the secondary
CPU. To get around this we have two options:
- Disable IRQ 7
- Stop the counter completely
This patch selects option two because this is the root of evil.. To be
on the safe side we will do it only in case the CEVT_R4K module is
disabled.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The scope of the SMP startup structure is wrong. It is created on the
stack and not as a global variable. This can lead to startup failures.
Fixes: 3f41360eb7 ("realtek: use upstream recommendation for CPU start")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Import patches from mtk-openwrt-feeds (MTK SDK) to support reading
t-phy settings affecting PCIe as well as USB2 and USB3 from efuse.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
efuse is used to store board-specific settings of some of the in-SoC
peripherals. Add it to device tree, so it gets probed on boot and can
be accessed by other drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow byte-wise access to mtk-efuse as some drivers require that.
Patch imported from mtk-openwrt-feeds (MTK SDK).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The corresponding kmod package is marked as HIDDEN and selected by all
other kernel modules that need it, so the kconfig side will be in sync
without manual selection
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Convert MAC address and label_mac configuration of Buffalo
WSR-1166DHP to use the generic function of OpenWrt.
Apply commit 770cfe9 for WCR-1166DS to WSR-1166DHP too.
Tested on the device and MAC address is kept before and after this
change.
Signed-off-by: Kazuhiro Ito <kzhr@d1.dion.ne.jp>
Instead of dropping *fix-typo-in-__mtk_foe_entry.patch which effectively
means keeping the (also wrong) assignment of MTK_FOE_STATE_BIND, rather
use MTK_FOE_STATE_INVALID as that works well on both older (NETSYS_V1)
and newer (NETSYS_V2) MediaTek SoCs.
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When the realtek clock driver was introduced, CONFIG_COMMON_CLK_REALTEK
was not correctly disabled for other subtarget. Add the missing config
flag to fix compilation error on buildbot.
Fixes: 4850bd887c ("realtek: add RTL83XX clock driver")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move and rename patches which were merged upstream and import follow-up
fixes for MediaTek Ethernet offloading features on MT7622 and Filogic
platforms. Remove patch
793-net-ethernet-mtk_eth_soc-fix-typo-in-__mtk_foe_entry.patch
which breaks hardware flow offloading on MT7622, it will be reverted
upstream as well.
Fixes: c93c5365c0 ("kernel: pick patches for MediaTek Ethernet from linux-next")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Don't overwrite AS_DPM and L2LEARNING flags when dest_port is >= 32.
Fixes: 1773264a0c ("realtek: correct egress frame port verification")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The generic imagebuilder does not have a generic in the name, although
this is the default naming scheme. Use bcm53xx as template for this fix.
Before the fix:
openwrt-imagebuilder-octeon.Linux-x86_64.tar.xz
After:
openwrt-imagebuilder-octeon-generic.Linux-x86_64.tar.xz
Signed-off-by: Nick Hainke <vincent@systemli.org>
If this module is not set to y, then I get the following compilation
error during geode build.
Package kmod-w83627hf-wdt is missing dependencies for the following libraries:
watchdog.ko
Setting the linux CONFIG_WATCHDOG_CORE to y as in all other targets
fixes this issue.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
If this module is not set to y, then I get the following compilation
error during geode build.
Package kmod-w83627hf-wdt is missing dependencies for the following
libraries:
watchdog.ko
Setting the linux CONFIG_WATCHDOG_CORE to y as in all other targets
fixes this issue.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.
Specification:
- SoC : Qualcomm IPQ4019
- RAM : DDR3 512 MiB (H5TC4G63EFR)
- Flash : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet : 10/100/1000 Mbps x2
- Transceiver : Qualcomm QCA8072
- WWAN : Telit LN940A9
- Z-Wave : Silicon Labs ZM5101
- Bluetooth : Qualcomm CSR8811
- Audio DAC : Realtek ALC5629
- Audio Amp. : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
- RGB LED, Fan, Temp. sensors
- Touch Sensor : Cypress CY8C4014LQI
- RGB LED driver : TI LP55231 (2x)
- LEDs/Keys : 11x, 6x
- UART : through-hole on PCB
- J1: 3.3V, TX, RX, GND from tri-angle marking
- 115200n8
- Power : 12 VDC, 2.5 A
Flash instruction using initramfs image:
1. Prepare TFTP server with the IP address 192.168.132.100 and place the
initramfs image to TFTP directory with the name "C0A88401.img"
2. Boot NCP-HG100/Cellular and interrupt after the message
"Hit any key to stop autoboot: 2"
3. Perform the following commands and set bootcmd to allow booting from
eMMC
setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
saveenv
4. Perform the following command to load/boot the OpenWrt initramfs image
tftpboot && bootm
5. On the initramfs image, perform sysupgrade with the sysupgrade image
(if needed, backup eMMC partitions by dd command and download to
other place before performing sysupgrade)
6. Wait for ~120 seconds to complete flashing
Known issues:
- There are no drivers for audio-related chips/functions in Linux Kernel
and OpenWrt, they cannot be used.
- There is no driver for MINI54FDE Micro-Controller Unit, customized for
this device by the firmware in the MCU. This chip controls the
following functions, but they cannot be controlled in OpenWrt.
- RGB LED
- Fan
this fan is controlled automatically by MCU by default, without
driver
- Thermal Sensors (2x)
- Currently, there is no driver or tool for CY8C4014LQI and cannot be
controlled. It cannot be exited from "booting mode" and moved to "normal
op mode" after booting. And also, the 4x buttons (mic mute, vol down,
vol up, alexa trigger) connected to the IC cannot be controlled.
- it can be exited from "booting mode" by installing and executing
i2cset command:
opkg update
opkg install i2c-tools
i2cset -y 1 0x14 0xf 1
- There is a connection issue on the control by uqmi for the WWAN module.
But modemmanager can be used without any issues and the use of it is
recommended.
- With the F2FS format, too many errors are reported on erasing eMMC
partition "rootfs_data" while booting:
[ 1.360270] sdhci: Secure Digital Host Controller Interface driver
[ 1.363636] sdhci: Copyright(c) Pierre Ossman
[ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
...
[ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.528325] mmc0: new HS200 MMC card at address 0001
[ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
[ 1.550323] Alternate GPT is invalid, using primary GPT.
[ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
...
[ 8.841400] mount_root: loading kmods from internal overlay
[ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.240465] block: attempting to load /etc/config/fstab
[ 9.246722] block: unable to load configuration (fstab: Entry not found)
[ 9.246863] block: no usable configuration
[ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
[ 9.438915] urandom_read: 5 callbacks suppressed
[ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[ 12.243332] mmc_erase: erase error -110, status 0x800
[ 12.246638] mmc0: cache flush error -110
[ 15.134585] mmc_erase: erase error -110, status 0x800
[ 15.135891] mmc_erase: group start error -110, status 0x0
[ 15.139850] mmc_erase: group start error -110, status 0x0
...(too many the same errors)...
[ 17.350811] mmc_erase: group start error -110, status 0x0
[ 17.356197] mmc_erase: group start error -110, status 0x0
[ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
[ 17.446910] mmc0: tuning execution failed: -5
[ 17.447111] mmc0: cache flush error -110
[ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
[ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
[ 18.198691] block: attempting to load /etc/config/fstab
[ 18.198972] block: unable to load configuration (fstab: Entry not found)
[ 18.203029] block: no usable configuration
[ 18.211371] mount_root: overlay filesystem has not been fully initialized yet
[ 18.214487] mount_root: switching to f2fs overlay
So, this support uses ext4 format instead which has no errors.
Note:
- The primary uart is shared for debug console and Z-Wave chip. The
function is switched by GPIO15 (Linux: 427).
value:
1: debug console
0: Z-Wave
- NCP-HG100/Cellular has 2x os-image pairs in eMMC.
- 0:HLOS, rootfs
- 0:HLOS_1, rootfs_1
In OpenWrt, the first image pair is used.
- "bootipq" command in U-Boot requires authentication with signed-image
by default. To boot unsigned image of OpenWrt, use "mmc read" and
"bootm" command instead.
- This support is for "Cellular" variant of NCP-HG100 and not tested on
"WLAN" (non-cellular) variant.
- The board files of ipq-wifi may also be used in "WLAN" variant of
NCP-HG100, but unconfirmed and add files as for "Cellular" variant.
- "NET" LED is used to indicate WWAN status in stock firmware.
- There is no MAC address information in the label on the case, use the
address included in UUID in the label as "label-MAC" instead.
- The "CLOUD" LEDs are partially used for indication of system status in
stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
connected to the MCU.
MAC addresses:
LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex))
WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))
partition layout in eMMC (by fdisk, GPT):
Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910
Number Start (sector) End (sector) Size Name
1 34 1057 512K 0:SBL1
2 1058 2081 512K 0:BOOTCONFIG
3 2082 3105 512K 0:QSEE
4 3106 4129 512K 0:QSEE_1
5 4130 4641 256K 0:CDT
6 4642 5153 256K 0:CDT_1
7 5154 6177 512K 0:BOOTCONFIG1
8 6178 6689 256K 0:APPSBLENV
9 6690 8737 1024K 0:APPSBL
10 8738 10785 1024K 0:APPSBL_1
11 10786 11297 256K 0:ART
12 11298 11809 256K 0:HSEE
13 11810 28193 8192K 0:HLOS
14 28194 44577 8192K 0:HLOS_1
15 44578 306721 128M rootfs
16 306722 568865 128M rootfs_1
17 568866 3958065 1654M rootfs_data
[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fix this occurrence during boot:
/bin/board_detect: line 10: Unsupported: not found
Fixes: 80baffd2aa (" ipq40xx: add support for Pakedge WR-1")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
On OEM firmware both addresses for In and Out ports are different. Set
them as such also in OpenWrt.
Fixes: e24635710c (" ipq40xx: add support for Luma Home WRTQ-329ACN")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
use the toolchain's default CPU (464fp) as the CPU option.
This fixes a CPU selection prompt which shows up now.
CPU selection
> 1. Generic 32 bits powerpc (POWERPC_CPU) (NEW)
2. Rely on the toolchain's implicit default CPU (TOOLCHAIN_DEFAULT_CPU) (NEW)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
