Commit Graph

14 Commits

Author SHA1 Message Date
Chuanhong Guo
ebf0d8dade ath79: add new ar934x spi driver
A new shift mode was introduced since ar934x which has a way better
performance than current bitbang driver and can handle higher spi
clock properly. This commit adds a new driver to make use of this
new feature.
This new driver has chipselect properly configured and we don't need
cs-gpios hack in dts anymore. Remove them.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-02-06 22:53:03 +08:00
Adrian Schmutzler
231dc26867 treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 16:44:06 +01:00
Jeff Kletsky
55e6c903ae ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel
The GL.iNet GL-AR300M has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.

This commit provides support for the NAND through the upstream
SPI-NAND framework. Devices with both NOR and NAND flash can support
independent firmware on each, with U-Boot able to boot from either.
The OEM U-Boot will fall back to the NOR firmware after three
"unsuccessful" boots.

The family of GL-AR300M devices on the ath79 platform now includes:

  * glinet,gl-ar300m-lite       "generic" target, NOR-only board
  * glinet,gl-ar300m-nand       "nand" target
  * glinet,gl-ar300m-nor        "nand" target (NAND-aware)

NB: This commit increases the kernel size from 2 MB to 4 MB

"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar300m-nor firmware produced by this commit:

  * gl-ar300m            -- OEM v3 NOR    ar71xx (openwrt-ar300m16-*.bin)
  * gl-ar300m            -- OpenWrt 18.06 ar71xx
  * gl-ar300m            -- OpenWrt 19.07 ar71xx

Other upgrades to these images should be performed through U-Boot.

The GL-AR300M OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.

The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated
after this commit should safely flash each other using sysupgrade.

The boot counter is implemented by the OEM using u-boot-env. At this
time, it does not appear that the switch on the side of the unit can
be used to select NOR vs. NAND boot and the fail-over is only from
NAND to NOR. To save flash wear, it is only reset when running the
glinet,gl-ar300m-nand firmware.

NAND-specific base-files are used to remove impact on existing
generic and tiny targets.

As there is now no "generic" build appropriate for the GL-AR300M16,
(or for users of the GL-AR300M that do not need access to NAND)
it will be introduced in a subsequent commit.

Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid

The ar71xx targets are unmodified.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00
Adrian Schmutzler
4176100b06 ath79: replace generic button node names
In several DTS files, button nodes are just named buttonX or
xxx_button. This replaces the names with more specific names matching
the majority of key definitions.

While at it, fix name of keys node in one case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-07 17:13:18 +01:00
Adrian Schmutzler
2b1baf9b16 ath79: remove redundant mtd-mac-address for wmac
For several devices, wmac MAC address is set from art 0x1002
explicitly by using mtd-mac-address although mtd-cal-data is
pulled from art 0x1000.

With the MAC address in 0x1002, the driver should automatically
use it when reading caldata from 0x1000. Thus, remove the
redundant mtd-mac-address for those devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Jeff Kletsky <git-commits@allycomm.com>
Tested-by: Karl Palsson <karlp@etactica.com>
2019-10-27 18:02:44 +01:00
Jeff Kletsky
736d16baad ath79: GL-AR300M series: Add I2C Support
The GL-AR300M series have an internal header for I2C.

Provide DTS definitions for the i2c-gpio driver.

The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,

Default clock measured ~11.4 ms period, ~88 kHz

The board has two sets of (unpopulated) headers.  While facing the
back of the board (looking into the Ethernet jacks), and looking from
the top, the one on the left edge of the baord with four holes is the
I2C header. It appears to be labeled J8 on "GL-AR300M-V1.4.0" boards.

    | (Patch antenna)
    |
    |
    |  O   GND
    |  O   SDA / GPIO 17
    |  O   SCL / GPIO 16
    |  ⊡   3V3 (square land)
    |
    | (Ethernet jacks)

https://docs.gl-inet.com/en/3/hardware/ar300m/#pcb-pinout states
"Note: I2C is not working in some early version of the router."

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-10-24 23:00:36 +02:00
Adrian Schmutzler
8961d2268e ath79: convert devices to interrupt-driven gpio-keys
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.

Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
2019-09-22 18:28:11 +02:00
Adrian Schmutzler
50fdc0374b ath79: provide label MAC address
This patch adds the label MAC address for several devices in
ath79.

Some devices require setting the MAC address in 02_network:

For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices

For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00
Adrian Schmutzler
d8ec6dee49 ath79: Add missing read-only properties
Add some read-only properties to protect partitions from
accidental changes.

Also fixed two whitespaces error on the way.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-11 16:37:11 +02:00
Jeff Kletsky
fefa34def8 ath79: Add GL.iNet AR-300M-Lite
AR300M-Lite is single-Ethernet variant of the AR300M series
Its eth0 would otherwise be assigned to the WAN interface
making it unreachable firstboot or failsafe.

Installation instructions from OEM (OpenWrt variant):
* Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI),
   * Do not preserve settings
   * Access rebooted device via Ethernet at OpenWrt default address

Add previously missing LED defaults for all three variants;
-nand, -nor, -lite to the definitions in 01_leds

Non-lite variants thanks to Andreas Ziegler
https://patchwork.ozlabs.org/patch/1049396/

Runtime-tested:  GL.iNet AR300M-Lite

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-03-13 16:25:34 +01:00
Luo chongjun
693c8fb0e3 ath79: Modify glinet x750 and AR300m MAC address offsets
In the production of glinet, the MAC address of ethernet port is
only written at the position where the ART area offset address
is 0, and the MAC address of eth1 is added 1 on the basis of eth0.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2019-02-28 11:32:55 +01:00
Jeff Kletsky
ee3120a9db ath79: fix GL.iNet AR300M family GPIOs/LEDs
Change the "status" LED to proper GPIO 12 and "red" naming.

Remove GPIO 2 from definition as a USB LED.

GPIO 2 is used to control power to the USB socket, not an LED.
As such, PWM on the line or typical LED triggers are inappropriate.

Users who wish to control the USB power for custom applications
can manipulate the GPIO through code, or for example, export it
through /sys/class/gpio/export.

Runtime-tested:  GL.iNet AR300M-Lite

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-01-26 10:40:06 +01:00
Paul Wassi
48745221a8 ath79: add status LED on GL.iNet AR300M
This adds the triggers for the status LED of this device.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:24:55 +01:00
Paul Wassi
6e78d546d1 ath79: fix boardname of GL.iNet GL-AR300M
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 14:24:21 +01:00