Commit Graph

254 Commits

Author SHA1 Message Date
Jeff Kletsky
819e7946b0 ipq40xx: Add support for Linksys EA8300 (Dallas)
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.

Installation:

  "Factory" images may be installed directly through the OEM GUI.

Hardware Highlights:

  * IPQ4019 at 717 MHz (4 CPUs)
  * 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
  * 256 MB RAM
  * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
      * 2.4 GHz radio at 30 dBm
      * 5 GHz radio on ch. 36-64 at 23 dBm
      * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
      #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
      * All two-stream, MCS 0-9
  * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
  * USB3, single port on rear with LED
  * WPS and reset buttons
  * Four status lights on top
  * Serial pads internal (unpopulated)

  "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"

Implementation Notes:

  The OEM flash layout is preserved at this time with 3 MB kernel and
  ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
  syscfg (56 MB) partitions are untouched, available as read-only.

Serial Connectivity:

  Serial connectivity is *not* required to flash.

  Serial may be accessed by opening the device and connecting
  a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
  including the ability to load images over TFTP and
  either run or flash them.

  Looking at the top of the board, from the front of the unit,
  J3 can be found on the right edge of the board, near the rear

      |
   J3 |
  |-| |
  |O| | (3.3V seen, open-circuit)
  |O| | TXD
  |O| | RXD
  |O| |
  |O| | GND
  |-| |
      |

Unimplemented:

    * serial1 "ttyQHS0" (serial0 works as console)
    * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)

Other Notes:

    https://wikidevi.com/wiki/Linksys_EA8300 states

        FCC docs also cover the Linksys EA8250. According to the
	RF Test Report BT BR+EDR, "All models are identical except
	for the EA8300 supports 256QAM and the EA8250 disable 256QAM."

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-18 13:43:54 +02:00
Jeff Kletsky
4bdc873a5f firmware/ipq-wifi: Extend for multi-chip boards
This package provides board-specific reference ("cal") data
on an interim basis until included in the upstream distros

While originally conceived for IPQ4019-based boards, similar needs
are appearing with three-radio devices. For some of these devices,
both a board-2.bin file needs to be supplied both for the IPQ4019
as well as for the other radio on the board.

This patch allows new or multiple overrides to be specified by:

  * Adding board name to ALLWIFIBOARDS
  * Placing file(s) in this directory named as
      board-<devicename>.<qca4019|qca9888|qca9984>
  * Adding
      $(eval $(call generate-ipq-wifi-package,<device>,<display name>))

(along with suitable package selection for the board)

At this time, QCA4019, QCA9888, and QCA9984 are supported.
Extension to other chips should be straightforward.

The existing files, board-*.bin, are "grandfathered" as QCA4019.

The package name has been retained for compatability reasons.
At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility.

Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac,
    avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300,
    engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-18 13:43:22 +02:00
Deng Qingfang
172b02c05f linux-firmware: update to 20190416
Update linux-firmware to 20190416, which includes updated firmwares e.g. for ath10k
Also switch to official tarball source.

The following firmware files we use are updated in this change:
ath10k/QCA6174/hw3.0/board-2.bin
ath10k/QCA9888/hw2.0/firmware-5.bin
ath10k/QCA988X/hw2.0/firmware-5.bin
ath10k/QCA9984/hw1.0/firmware-5.bin
mrvl/sd8887_uapsta.bin
mrvl/pcie8897_uapsta.bin
iwlwifi-8000C-36.ucode
iwlwifi-8265-36.ucode

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-05-14 21:59:38 +02:00
Robert Marko
61f4ceb146 ath10k-firmware: update Candela Tech firmware images
Release notes since last time:

Release notes for wave-1:

2019-04-02: Support some get/set API for eeprom rate power tables.
	    Mostly backported from 10.2

2019-04-02: Support adaptive-CCA, backported from 10.2

2019-04-02: Support adding eeprom configAddr pairs via the
            set-special API. These configAddrs can be used to change
            the default register settings for up to 12 registers.

2019-05-03: Fix tx-power settings for 2x2, 3x3 rates.
	    Original logic I put in back in 2016 set 2x2 and 3x3 lower
	    than the needed to be when using most NICs (very high
	    powered NICs would not have been affected I think, not sure
	    any of those exist though.)

	    This improves throughput for 2x2 and 3x3 devices,
	    especially when the signal is weaker.

Release notes for wave-2:

2019-04-08: When setting keys, if high bit of high value of
	    key_rsc_counter is set to 0x1, then the lower 48 bits will
	    be used as the PN value.  By default, PN is set to 1 each
	    time the key is set.

2019-04-08: Pack PN into un-used 'excretries' aka
	    'num_pkt_loss_excess_retry' high 16 bits.
	    This lets us report peer PN, but *only* if driver has
	    previously set a PN when setting key (or set-special cmd is
	    used to enable PN reporting).

	    This is done so that we know the driver is recent
            enough to deal with the PN stat reporting.

2019-04-16: Support specifying tx rate on a per-beacon packet.
	    See ath10k_wmi_op_gen_beacon_dma and
	    ath10k_convert_hw_rate_to_rate_info for API details.

	     Driver needs additional work to actually enable this
	     feature currently.

2019-04-30: Compile out tx-prefetch caching logic.
	    It is full of tricky bugs that cause tx hangs.
	    I fixed at least one, but more remain and I have wasted too
	    much time on this already.

2019-05-08: Start rate-ctrl at mcs-3 instead of mcs-5.
	    This significantly helps DHCP happen quickly, probably
	    because the initial rate being too high would take a while
	    to ramp down, especially since there are few packets sent
	    by the time DHCP needs to start.

	    This bug was triggered by me decreasing retries of 0x1e
	    (upstream default) to 0x4.  But, I think it is better to
	    start with lower initial MCS instead of always having a
	    very high retry count.

Tested on 8devices Jalapeno dev board(IPQ4019)

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [neatify]
2019-05-11 16:37:11 +02:00
Christian Lamparter
fbe2e7d15e ath10k-firmware: update Candela Tech firmware images
Release notes since last time:

Release notes for wave-1 / 10.1:
2019-03-28: Fix sometimes using bad TID for management frames
	    in htt-mgt mode. (Backported from wave2, looks
	    like bug would be the same though.)

Release notes for wave-2 / 10.4:
2019-03-28: Fix off-channel scanning while associated in
	    proxy-station mode.

2019-03-29: Fix sometimes sending mgt frames on wrong tid when
	    using htt-mgt. This bug has been around since I first
	    enabled htt-mgt mode.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-30 10:36:31 +01:00
Christian Lamparter
f803ee3ba9 ath10k-firmware: update Candela Tech firmware images
Release notes since last time:

Release notes for wave-1:

- 2019-03-12: Add btcoex feature flag for 2.4Ghz only adapters,
	      backported from upstream 10.2 firmware.

- 2019-03-12: Support offloading decrypt of PMF blockack frames
	      to the host. This lets us do blockack with PMF and
	      rx-sw-crypt. Normal hwcrypt scenarios would not need this.

Release notes for wave-2:

- 2019-03-12: Fix crash when tearing down VI TID when pending frames
	      exist. Could reproduce this while doing rmmod when VI
	      traffic was flowing and PMF was enabled but broken.
	      Bad luck could rarely cause it to happen in more normal
	      config too.

- 2019-03-12: Support offloading decrypt of PMF blockack frames to
	      the host.  This lets us do blockack with PMF and
	      rx-sw-crypt. Normal hwcrypt scenarios would not need this.

- 2019-03-12: Re-work problematic patch that attempted to fix transmit
	      on non-QOS tids. It appears buggy in several ways,
	      hopefully improved now.  This was introduced last fall.
	      See github bug 78.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-25 21:19:39 +01:00
Steve Glennon
dc4f6b896f ipq40xx: add support for EnGenius ENS620EXT
Hardware
--------
CPU:   Qualcomm IPQ4018
RAM:   256M
FLASH: 32M SPI NOR W25Q256
ETH:   QCA8075
WiFi2: IPQ4018 2T2R 2SS b/g/n
WiFi5: IPQ4018 2T2R 2SS n/ac
LED:    - Power amber
        - LAN1(PoE) green
        - LAN2 green
        - Wi-Fi 2.4GHz green
        - Wi-Fi 5GHz green
BTN:    - WPS
UART:  115200n8 3.3V J1
       VCC(1) - GND(2) - TX(3) - RX(4)

Added basic support to get the device up and running for a sysupgrade
image only.
There is currently no way back to factory firmware, so this is a one-way
street to OpenWRT.
Install from factory condition is convoluted, and may brick your device:
1) Enable SSH and disable the CLI on the factory device from the web user
   interface (Management->Advanced)
2) Reboot the device
3) Override the default, limited SSH shell:
   a) Get into the ssh shell:
      ssh admin@192.168.1.1 /bin/sh --login
   b) Change the dropbear script to disable the limited shell. At the
      empty command prompt type:
        sed -i '/login_ssh/s/^/#/g’ dropbear
        /etc/init.d/dropbear restart
        exit
4) ssh in to a (now-) normal OpenWRT SSH session
5) Flash your built image
   a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
      admin@192.168.1.1:/tmp/
   b) ssh admin@192.168.1.1
   c) sysupgrade -n
      /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
6) After flash completes (it may say "Upgrade failed" followed by
   "Upgrade completed") and device reboots, log in to newly flashed
   system. Note you will now need to ssh as root rather than admin.

Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
[whitespace fixes, reordered partitions, removed rng node from 4.14,
fixed 901-arm-boot-add-dts-files.patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
David Bauer
148d29d47b ipq40xx: add support for AVM FRITZ!Repeater 3000
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH:   Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED:    - Connect green/blue/red
        - Power green
BTN:   WPS/Connect
UART:  115200n8 3.3V
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ3000.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz3000.bin uboot0
   > mtd write /path/to/uboot-fritz3000.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:35 +01:00
Piotr Dymacz
6ee73942f9 ipq-wifi: update ALFA Network AP120C-AC board-2.bin
Add specific 'variant' for 'bus=ahb,bmi-chip-id=0,bmi-board-id=25' BDF.
Use the same value ('ALFA-Network-AP120C-AC') as sent upstream.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-08 19:28:31 +01:00
Michael Yartys
fc2fd1c9d6 ath10k-firmware: update Candela Tech firmware images
Release notes since last update:

wave-1 firmware:

*  Feb 14, 2019:  Remove logic that causes assert when swba logic is not
                  initialized. This was seen when trying to bring up 6 VAP
                  vdevs. A similar fix went into wave-2 firmware some time
                  ago.

*  Feb 27, 2019:  Support up to 32 vAP vdevs, fix stack corruption when
                  driver requests too many vAP.

*  Feb 28, 2019:  Support beacon-tx-wmi callback message. This lets driver
                  properly clean up beacon buffers so we don't crash
                  (somethings the entire OS/system) due to DMA errors.

wave-2 firmware:

*  Feb 27. 2019:  Support up to 32 AP vdevs. Previous to this, stack would
                  be corrupted if you went past 16 AP vdevs.

*  Feb 28, 2019:  Support beacon-tx-wmi callback message. This lets driver
                  properly clean up beacon buffers. In wave-1, this could
                  crash the entire OS, but I didn't see the same crashes
                  in wave-2, so maybe it is fixed in some other way. Add
                  the feature regardless as it seems proper.

Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
2019-03-06 21:58:59 +01:00
David Bauer
95b0c07a61 ipq40xx: add support for FritzBox 7530
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M
FLASH: 128M NAND
ETH:   QCA8075
VDSL:  Intel/Lantiq VRX518 PCIe attached
       currently not supported
DECT:  Dialog SC14448
       currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED:    - Power/DSL green
        - WLAN green
        - FON/DECT green
        - Connect/WPS green
        - Info green
        - Info red
BTN:    - WLAN
        - FON
        - WPS/Connect
UART:  115200n8 3.3V (located under the Dialog chip)
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ7530.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz7530.bin uboot0
   > mtd write /path/to/uboot-fritz7530.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:32:55 +01:00
张鹏
bbab33724d ipq40xx: add support for Qxwlan E2600AC C1 and C2
Qxwlan E2600AC C1 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
FLASH:	32 MiB Winbond W25Q256
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Qxwlan E2600AC C2 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
NOR:	16 MiB Winbond W25Q128
NAND:	128MiB Micron MT29F1G08ABAEAWP
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "ubi" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Piotr Dymacz
d3f82d3b84 ipq-wifi: add board-2.bin for ALFA Network AP120C-AC
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:16:22 +01:00
Oever González
81adb132da ipq-wifi: update ipq-wifi for Linksys EA6350v3
This commit updates the file "board-linksys_ea6359v3".

Without this commit, the Linksys EA6350v3 will experience poor wireless
performance in both bands. With this patch, wireless performace will be
comparable to the performance of the stock firmware.

Signed-off-by: Oever González <notengobattery@gmail.com>
2019-02-20 18:51:31 +01:00
Christian Lamparter
d38789b559 firmware: ipq-wifi: mark packages as nonshared
The board-files are specific to the target and device. Hence
they need to be set as nonshared. Otherwise they do not show
up on the package repository. This causes problems for
imagebuilder, if it needs to build a image for a specific
device that hasn't had the time to have get its boardfile
upstream.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-20 18:51:31 +01:00
Lucian Cristian
b06418016d linux-firmware: DRM: add amdgpu firmware
add firmware needed for amdgpu DRM display

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2019-02-17 19:22:39 +01:00
Lucian Cristian
22fdaa06b7 linux-firmware: DRM: add radeon firmware
add firmware needed for radeon DRM display

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2019-02-17 19:22:39 +01:00
Pawel Dembicki
1559682757 linux-firmware: broadcom: package 43430a0 FullMAC firmware
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-02-17 19:22:39 +01:00
Marius Genheimer
9ad3967f14 ipq40xx: add support for ASUS Lyra
SoC:   Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM:   256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT:    Atheros AR3012
IN:    WPS Button, Reset Button
OUT:   RGB-LED via TI LP5523 9-channel Controller
UART:  Front of Device - 115200 N-8
       Pinout 3.3v - RX - TX - GND (Square is VCC)

Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.

2. Login to the device via SSH.

3. Flash the initramfs image using

> mtd-write -d linux -i openwrt-image-file

4. Power-cycle the device and wait for OpenWRT to boot.

5. From there flash the OpenWRT-sysupgrade image.

Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.

Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-14 16:56:15 +01:00
Christian Lamparter
465044d0fd ath10k-firmware: update Candela Tech firmware images
Release notes since last time:

2019-02-08:
  Fix rate-ctrl assert related to bad logic that tried to guess
  that lower bandwidth probes were automatically successful if
  higher was. The NSS mismatch that can happen here caused the
  assert. Just comment out the offending code
  (per comment from original QCA code). This is bug 69.

2019-02-10:
  Fix bssid mis-alignment that broke 4-addr vlan mode (bug 67).
  Original buggy commit was
  commit 2bf89e70ecd1 ("dev-ds: Better packing of wal_vdev struct.")

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-11 19:02:41 +01:00
Koen Vandeputte
5a8d03ceeb ath10k-firmware: update Candela Tech firmware images
*  Jan 2, 2019
Rebase patches to make 9980 bisectable.

*  Jan 2, 2019
Fix scheduling related assert when wal-peer is deleted with pending
tx buffers (bug 54, and others)

*  Jan 7, 2019:
Fix specifying retransmits for AMPDU frames.  It was previously ignored
since it is a 'software' retransmit instead of a hardware retransmit.

*  Jan 9, 2019
Fix potential way to get zero rates selected (and then assert)

*  Jan 18, 2019
pfsched has specific work-around to just return if we find invalid flags AND
if we are in an out-of-order situation.  Maybe this is last of the pfsched
related issues (bug 54 and similar).

*  Jan 24, 2019
The rcSibUpdate method can be called concurrently with IRQ tx-completion callback,
and that could potentially allow the tx-completion callback to see invalid state
and assert or otherwise mess up the rate-ctrl logic.  So, disable IRQs in
rcSibUpdate to prevent this.  Related to bug 58.

*  Jan 28, 2019
Ensure that cached config is applied to ratectrl objects when fetched from
the cache.  This should fix part of bug 58.

*  Jan 28, 2019
Ensure that ratectrl objects from cachemgr are always initialized.  This fixes
another part of bug 58.

*  Jan 30, 2019
Better use of temporary rate-ctrl object.  Make sure it is initialized, simplify
code path.  This finishes up porting forward similar changes I made for wave-1
firmware long ago, and fixes another potential way to hit bug-58 issues.

*  Jan 30, 2019
Cachemgr did not have a callback for when memory was logically freed.  This means
that peers could keep stale references to rate-ctrl objects that were in process
of being DMA'd into to load a different peer's rate-ctrl state.  This was causing
the bugcheck logic to fail early and often, and I suspect it might be a root cause
of bug 58 as well.  The fix is to add a callback and set any 'deleted' memory references
to NULL so that we cannot access it accidentally.  Thanks to excellent logs and patience
from the bug-58 reporter!

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-04 12:09:35 +01:00
Oever González
fb7b8d5ad3 ipq-wifi: add support for Linksys EA6350v3
This commit adds support for the Linksys EA6350v3 device in the ipq-wifi
target.

Without this patch, the Linksys EA6350v3 won't be hable to have fully
functional wireless interfaces. This is not permanent: the board data has
already been sent to ath10k _at_ lists _dot_ infradead _dot_ org

Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
2019-01-26 21:42:57 +01:00
Jo-Philipp Wich
c0248183a4 ath10k-firmware: update Candela Tech firmware images
- Removed an assert from wave-1 firmware images
 - Fix three recently reported firmware crashes in wave-2 images

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-12-20 09:23:45 +01:00
Rafał Miłecki
fa211623d0 linux-firmware: broadcom: package 4366C0 FullMAC firmware
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-17 12:51:00 +01:00
Rafał Miłecki
8b4f6a1d2a linux-firmware: update to the commit from 2018-12-16
It includes e.g. new Broadcom FullMAC firmwares for 4366B1 and 4366C0.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-17 11:42:45 +01:00
Michael Yartys
cc5c63f217 ath10k-firmware: update all CT firmware variants
Wave-1 firmware (988x, 9887): bug fixes
Wave-2 firmware (4019, 9888, 99x0, 9984): fix protected management frames, rate-ctrl fixes, and performance improvements

Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
2018-12-15 15:25:24 +01:00
Christian Lamparter
87af41d554 ath10k-firmware: Fix mirror hash sum (FS#1983)
This now matches what was generated locally on my PC and the file on the
mirror server.

Fixes: 575d0240f9 ("ath10k-firmware: update board-2.bin for community firmwares")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-09 15:07:02 +01:00
Steven Lin
2b4ac79a79 ipq40xx: add support for EnGenius EAP1300
SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
NOR:    32 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button
LEDS:   Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm

2. Load image via GUI

a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.

3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin

Signed-off-by: Steven Lin <steven.lin@senao.com>
2018-12-05 09:40:32 +01:00
John Crispin
231d9d5327 Revert "intel-microcode: create early load microcode image"
This reverts commit 022ffb56b2.

Signed-off-by: John Crispin <john@phrozen.org>
2018-11-27 18:58:37 +01:00
John Crispin
30f30d3e11 Revert "amd64-microcode: create early load microcode image"
This reverts commit 975019b3a7.

Signed-off-by: John Crispin <john@phrozen.org>
2018-11-27 18:58:33 +01:00
Tomasz Maciej Nowak
975019b3a7 amd64-microcode: create early load microcode image
Create initrd image with packed microcode. This'll allow to load it at
early boot stage.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:45 +01:00
Tomasz Maciej Nowak
022ffb56b2 intel-microcode: create early load microcode image
Create initrd image with packed microcode. This'll allow to load it at
early boot stage.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Tomasz Maciej Nowak
ad83fde30d intel-microcode: remove dependency on iucode-tool
It is not necessary to have iucode-tool present on target system to have
functional intel-microcode package. The build time dependency is kept.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Christian Lamparter
dceee8cc09 ipq-wifi: drop custom board-2.bins
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and linux-firmware.git.

We switched to the upstream board-2.bin, hence the files can be removed
here.

Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-01 17:16:53 +01:00
Christian Lamparter
575d0240f9 ath10k-firmware: update board-2.bin for community firmwares
This patch updates the board-2.bin for the default
IPQ4019, QCA9984 and QCA9888 ath10k-firmware-xyz-ct
and -ct-htt firmwares.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-01 17:16:52 +01:00
Hauke Mehrtens
e1db49310e linux-firmware: intel: Add iwl 9000 and 9260 firmware
Add the most recent supported firmware file for the Intel 9000 and
9260 wireless chips. The API version 41 is not yet supported by the driver.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-10-20 16:24:29 +02:00
Hauke Mehrtens
10dffe2fa3 linux-firmware: intel: update firmware files for 7265D, 8000C and 8265
Use more recent versions for the Intel wireless chips 7265D, 8000C and 8265.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-10-20 16:24:29 +02:00
Robert Marko
f6a26f9a20 linux-firmware: Update linux-firmware to 2018-10-18
Kalles ath10k PR was finally merged so update linux-firmware to
include those changes.

This is needed since disabling ath10k-firmware a lot of custom BDF-s
in board-2.bin-s are not available in previously outdated linux-firmware
board-2.bin-s.
This also includes support for boards currently using ipq-wifi and other
WIP ones.

Runtime tested on 8devices Jalapeno.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-10-20 16:13:39 +02:00
Hauke Mehrtens
90bb790fbf intel-microcode: update to version 20180807a
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-10-07 02:12:06 +02:00
Daniel Golle
b88df4a7c8 linux-firmware: set PKG_MIRROR_HASH
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-09-26 16:35:33 +02:00
John Crispin
0a1faecdb5 linux-firmware: add ath10k support
Signed-off-by: John Crispin <john@phrozen.org>
2018-09-26 16:35:33 +02:00
John Crispin
9860cdda76 ath10k-firmware: disable the package and use default linux-firmware package
Signed-off-by: John Crispin <john@phrozen.org>
2018-09-26 16:35:33 +02:00
Yangbo Lu
87d7a596ec layerscape: build ls-dpl package with linux dtc tool
Building ls-dpl package requires the dtc tool. This patch
is to support using linux dtc tool for ls-dpl package.
This avoids compile issue when host system doesn't have
the dtc tool.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:58 +02:00
Yangbo Lu
7016dd48f1 layerscape: add ls1012afrwy support and drop ls1012afrdm
ls1012afrdm was no longer supported in NXP Layerscape SDK.
Instead a new board ls1012afrwy was introduced in LSDK.
This patch is to drop ls1012afrdm and add ls1012afrwy support.
Since only 2MB NOR flash could be used, we just put u-boot
and firmware on NOR flash, and put kernel/dtb/rootfs on SD
card.

The Layerscape FRWY-LS1012A board is an ultra-low-cost
development platform for LS1012A Series Communication
Processors built on Arm Cortex-A53. This tool refines the
FRDM-LS1012A with more features for a better hands-on experience
for IoT, edge computing, and various advanced embedded
applications. Features include easy access to processor I/O,
low-power operation, micro SD card storage, an M2 connector, a
small form factor, and expansion board options via mikroBUS Click
Module. The MicroBUS Module provides easy expansion via hundreds
of powerful modules supporting sensors, actuators, memories,
and displays.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:57 +02:00
Yangbo Lu
eb684205e5 layerscape: add SD card boot support
NOR/QSPI Flash on Layerscape board only has limited 64MB memory size.
Since some boards (ls1043ardb/ls1046ardb/ls1088ardb/ls1021atwr)
could support SD card boot, we added SD boot support for them to put
all things on SD card to meet large memory requirement.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:57 +02:00
Yangbo Lu
f0ec7bd27d layerscape: add armv7 subtarget and ls1021atwr board support
The NXP TWR-LS1021A module is a development system based
on the QorIQ LS1021A processor.
- This feature-rich, high-performance processor module can
  be used standalone or as part of an assembled Tower System
  development platform.
- Incorporating dual Arm Cortex-A7 cores running up to 1 GHz,
  the TWR-LS1021A delivers an outstanding level of performance.
- The TWR-LS1021A offers HDMI, SATA3 and USB3 connectors as
  well as a complete Linux software developer's package.
- The module provides a comprehensive level of security that
  includes support for secure boot, Trust Architecture and
  tamper detection in both standby and active power modes,
  safeguarding the device from manufacture to deployment.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:57 +02:00
Yangbo Lu
32bb763e45 layerscape: update ls-ppa to LSDK-18.06
This patch is to update ls-ppa to LSDK-18.06 release
and to rework ls-ppa makefile to make it more readable.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:56 +02:00
Yangbo Lu
89c4ed57b7 layerscape: update ls-rcw to LSDK-18.06
The rcw source code had been migrated to codeaurora
for LSDK-18.06 release and the future release. The
source code had also involved ls1012ardb/ls1012afrdm/
ls1088ardb/ls2088ardb rcw, so we updated ls-rcw to
LSDK-18.06, reworked the makefile and dropped ls-rcw-bin
package in this patch. Also reworked ls-rcw patch to
adapt to the latest source code.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:56 +02:00
Yangbo Lu
984cf8d89d layerscape: update ppfe-firmware to LSDK-18.06
This patch is to update ppfe-firmware to LSDK-18.06 release.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:56 +02:00
Yangbo Lu
c19f520686 layerscape: update ls-mc to LSDK-18.06
This patch is to update ls-mc to LSDK-18.06 release.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:56 +02:00