Add em_ipset module to support tc filter classification by IP set. Build
as a standalone package to help avoid pulling in rest of kmod-sched and
isolate new dependency on kmod-ipt-ipset.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add act_pedit, act_csum, act_gact and act_simple modules for additional
tc action support. Module act_simple helps with debug and logging, similar
to iptables LOG target, while act_gact provides common generic actions.
Modules act_pedit and act_csum support general packet mangling, and have
been the subject of feature requests and forum discussions (e.g. DSCP),
as well as being added to the Turris OS fork of OpenWrt ~2 years ago.
Also select dependency kmod-lib-crc32c to support act_csum.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
All tc ematch modules, including those in kmod-sched-core and kmod-sched,
use cls_basic as a core dependency. Relocate cls_basic from kmod-sched to
kmod-sched-core to avoid requiring kmod-sched unnecessarily.
This change is also backwards compatible since any past tc ematch users
will have had to install both kmod-sched-core and kmod-sched anyway.
Add the matchall kernel module cls_matchall introduced in kernel 4.8. The
matchall classifier matches every packet and allows the user to apply
actions on it. It is a simpler, more efficient replacement for the common
but cryptic tc classifier idiom "u32 match u32 0 0".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9561
RAM: 64M DDR2
FLASH: 16M SPI-NOR
ETH: 1x WAN - 2x LAN
WiFi: QCA9561 3T3R
BTN: 1x Reset - 1x WPS
LED: 1x Blue - 1x Red - 1x Yellow
UART: TX - GND - RX - VCC (From ethernet port)
115200n8 - 3.3V
Installation
------------
1. Connect to the device via UART.
2. Interrupt the U-Boot on power-on by pressing enter when prompted.
3. Connect you computer to one of the routers LAN ports.
Assign yourself the IP 192.168.31.10/24.
Copy the OpenWRT initramfs image to a tftp server root directory.
Rename the image to 'x4q.bin'.
4. Load the initramfs image to the router by executing following command
in U-Boot. The image will boot afterwards.
> tftpboot 0x81000000 x4q.bin; bootm
5. SCP the sysupgrade-image into '/tmp'.
Remember to assign yourself an IP in 192.168.1.0/24 for this step!
6. Install OpenWRT permanently by executing
> sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>
Signed-off-by: David Bauer <mail@david-bauer.net>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the
management packets rate to the firmware.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Release notes since last time:
2019-02-08:
Fix rate-ctrl assert related to bad logic that tried to guess
that lower bandwidth probes were automatically successful if
higher was. The NSS mismatch that can happen here caused the
assert. Just comment out the offending code
(per comment from original QCA code). This is bug 69.
2019-02-10:
Fix bssid mis-alignment that broke 4-addr vlan mode (bug 67).
Original buggy commit was
commit 2bf89e70ecd1 ("dev-ds: Better packing of wal_vdev struct.")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The KERNEL_ENTRY was missing from the DEFAULT_DEVICE_VARS.
This bug was discovered while preparing alternative images
for the mpc85xx's TP-Link WDR4900-V1, which all failed to
boot due to this:
|## Booting kernel from Legacy Image at 02000000 ...
| Image Name: POWERPC OpenWrt Linux-4.14.96
| Image Type: PowerPC Linux Kernel Image (uncompressed)
| Data Size: 2056568 Bytes = 2 MiB
| Load Address: 01000000
| Entry Point: 00000000
| Verifying Checksum ... OK
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit 7ebbbda293 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
adds support for using the RSSI strenght via LEDS.
The rssileds package addition got lost during altering the patch.
Add it again to fix this.
Fixes: 7ebbbda293 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Update mpfr to 4.0.2
Use official site as last resort
Force thread-safety functionality
Refresh patches
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
9f44fa22cb Add compiler barriers around modifications of the robust mutex list for pthread_mutex_trylock. [BZ #24180]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Same reasoning as in bdedb798150a58ad7ce3c4741f2f31df97e84c3f; don't set
default firewall zone to wan as the firewall zone for the vti interface
can be configured in the firewall config or it makes it impossible not to
specify a firewall zone for the vti interface.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Same reasoning as in bdedb798150a58ad7ce3c4741f2f31df97e84c3f; don't set
default firewall zone to wan as the firewall zone for the ipip interface
can be configured in the firewall config or it makes it impossible not to
specify a firewall zone for the ipip interface.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This patch uses nfct_help() to detect whether an established connection
needs conntrack helper instead of using test_bit(IPS_HELPER_BIT,
&ct->status).
The reason for this modification is that IPS_HELPER_BIT is only set when
the conntrack helper is attached by explicit CT target.
However, in the case that a device enables conntrack helper via the other
ways (e.g., command "echo 1 > /proc/sys/net/netfilter/nf_conntrack_helper")
, the status of IPS_HELPER_BIT will not present any change. That means the
IPS_HELPER_BIT might lose the checking ability in the context.
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM and XW family, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
Also add the required package for this.
While at that, remove coefficients needed for PWM LEDs, as XM and XW
boards do not support PWM LEDs.
Tested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[Squashed commits + remove custom device_packages + slighty rewrite the commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Some hAP lite routers aren't detected because
/proc/cpuinfo shows "RouterBOARD RB941-2nD"
instead of "RouterBOARD 941-2nD".
Fix that.
Signed-off-by: Julien Rabier <taziden@flexiden.org>
[Alter string to include all flavours + slight rewrite of commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
While preparing 4.19 for imx6 and test building it with
CONFIG_ALL_KMODS=y with verbose mode enabled, I was asked by kernel
config about few missing symbols/modules
Let's add them to the generic config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[slight rewrite of commit log]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Remove 980-rt2x00-reduce-power-consumption-on-mt7620.patch which in
combination with the most recently added patch reportedly causes TX
power to be too weak.
"without patches rssi on receiver is ~ -23dBm with 980 about -35dBm,
with both patches drops below -40dBm. with 987 only ~-28dBm"
We may need to reconsider this once we have implemented TSSI.
Fixes: cdb58b2bfe ("mac80211: rt2x00: reduce tx power to nominal level on RT6352")
Reported-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixed CVEs:
CVE-2018-16890
CVE-2019-3822
CVE-2019-3823
For other changes in version 7.64.0 see https://curl.haxx.se/changes.html#7_64_0
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Current implementation of RT6352 support provides too high tx power
at least on iPA/eLNA devices. Reduce amplification of variable gain
amplifier by 6dB to match board target power of 17dBm.
Transmited signal strength with this patch is similar to that of
stock firmware or pandorabox firmware. Throughput measured with iperf
improves. Device tested: Xiaomi Miwifi Mini.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There are two problems with this behaviour that the zone is set to wan
if no zone config option is defined in the interface section.
* The zone for the interface is "normally" specified in the firewall
config file. So if we have defined "no" zone for this interface zone
option is set now to "wan" additonaly if we add the interface in the firewall
config section to the "lan" zone, the interface is added to lan and wan at once.
iptables-save | grep <iface>
This is not what I expect.
* If I do not want to set a zone to this interface it is not possible.
Remove the default assigment to wan if no zone option is defined.
If some one need the option it stil possible to define this option.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during
network setup[1] which I was able to reproduce easily with following commands:
uci set network.lan.ipaddr='192.168.1.20'
uci commit network
ifup lan
Which resulted after some time in:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280
NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out
...
Sometimes I wasn't able to use networking anymore, sometimes it was enough to
just ifdown/ifup lan and network was backup. On ar71xx it was all working just
fine.
I've found out, that it was happening because ag71xx_poll() wasn't called, thus
the TX queue wasn't emptied. The ag71xx_poll() is being called from napi
hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since
no interrupts were ever fired again after ag71xx_stop() was called, it was
always leading to tx queue timeouts:
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
eth0: raw intr=00000001 TXPS POLL
eth0: enable polling mode
eth0: processing TX ring, flush=no
eth0: disable polling mode, rx=1, tx=1,limit=32
( `ifup lan done here` )
*** ag71xx_stop()
*** ag71xx_open()
*** ag71xx_hw_enable()
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274
So I've looked at ag71xx_stop() in ar71xx, added the missing bits to ath79 and
fixed this issue.
1. https://github.com/openwrt/openwrt/pull/1635#issuecomment-448638246
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[move ag->link before ag71xx_hw_disable to retain ordering as original]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The package hash does not match the one of the package found on the
mirrors and which is generated when I do the git clone.
Fixes: 4856fa30a6 ("nat46: import for routing, add myself as maintainer")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Restoring the bootloader config before rebooting fails:
tar: invalid tar magic
Add the -z option to the tar command to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
It was reported to me today on IRC, that building of artifacts doesn't
work properly if the concat_cmd references DEVICE_NAME variable. I've
found out, that it's due to missing call of Device/Export in artifacts
building code path, so this patch adds the missing Device/Export call
which in turn exports DEFAULT_DEVICE_VARS into the artifacts
environment.
Fixes: 493c9a3551 ("build: Introduce building of artifacts")
Tested-by: Oskari Lemmela <oskari@lemmela.net>
Reported-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This option was a spi nor hack which is dropped in commit
bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.
Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
<https://www.openwall.com/lists/musl/2019/01/21/8>
"This release makes improvements with respect to default thread stack
size, including increasing the default from 80k to 128k, increasing
the default guard size from 4k to 8k, and allowing the default to be
increased via ELF headers so that programs that need larger stacks can
be build without source-level changes, using just LDFLAGS.
Insufficient stack size for AIO threads on kernels that don't honor
the constant MINSIGSTKSZ is also fixed.
The glob core has been rewritten to fix inability to see past
searchable-but-unreadable path components, and to avoid excessive
stack usage and unnecessary syscalls. The tsearch AVL tree
implementation has also been rewritten for better size and
performance. The math library adds more native single-instruction
implementations for arm, s390x, powerpc, and x86_64.
Various bugs are fixed, including several possible deadlocks, one of
which was a new regression in 1.1.20."
detailed release notes can be found in the WHATSNEW file:
<http://git.musl-libc.org/cgit/musl/tree/WHATSNEW#n1989>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch fixes the ASUS' RT-AC58U port order by
unifying the configuration with the NBG6617.
Reported-by: Roberto Socrates (rtac58u-user on the forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch splits the big board case switch in 02_network in
two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs()
just like ath79 and ramips do.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
