Commit Graph

3 Commits

Author SHA1 Message Date
Adrian Schmutzler
226bc91109 ath79: improve TP-Link CPE DTSI names for ar9344 SOC
The initial DTSI names for the TP-Link CPE devices have become
quite confusing, as several non-V1 devices now use the *-v1.dtsi,
the *cpe510-v1.dts does not use the cpe510.dtsi, etc.

This introduces a new naming scheme based on whether devices have
one or two ports, which should be easier to grasp.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-23 12:03:49 +01:00
Bernhard Geier
3930aab2cb ath79: add support for TP-Link WBS210 v2
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with
two Ethernet ports based on Atheros AR9344

The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm
instead of 12 dBm) and two antenna connectors instead of built-in antennas.

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
 - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP: 192.168.0.100
Stock device TFTP adress: 192.168.0.254

The TP-Link WBS devices use the same GPIOs as the CPE devices,
except for the link4 LED. For this one, WBS devices use "2", while
CPE devices use "16". (Tested on WBS210 v2)

Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[added comment about GPIO]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 13:59:18 +01:00
Adrian Schmutzler
0104eed1e5 ath79: add support for TP-Link CPE510 v1
TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with
two Ethernet ports based on Atheros AR9334

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 2T2R 5 GHz
 - 13 dBi built-in antenna
 - Power, LAN0, LAN1 green LEDs
 - 4x green RSSI LEDs

Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Based on the work of Paul Wassi <p.wassi@gmx.at>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00