Commit Graph

83 Commits

Author SHA1 Message Date
Adrian Schmutzler
e0382e88a9 ipq806x: build DEVICE_DTS based on SOC and device name
This patch uses the SOC variable to calculate DTS names automatically
based on the SOC and the device definition node name.

This reduces redundancy and (by having to choose DTS name
appropriately) will unify the naming of a device in different places
(image/Makefile, DTS name, compatible, image name). This is supposed
to make life easier for developers and reviewers.

Since the kernel uses a "soc-device.dts" scheme for this target, we
use this for the derivation of DEVICE_DTS, too, leaving the DTS names
unchanged for this target.

Note that for some devices the kernel itself uses inconsistent names
(DTS naming scheme vs. compatible), leaving us with a manual overwrite
of DEVICE_DTS for those cases.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-27 18:00:32 +01:00
Moritz Warning
2afb3a56f1 ipq806x: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-08-02 22:45:02 +02:00
INAGAKI Hiroshi
51fe956c4f ipq806x: add support for Buffalo WXR-2533DHP
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

The U-Boot on WXR-2533DHP employs a complicated dual firmware
protection scheme against corruptions of the kernel and rootfs
images. See the notes in buffalo.sh for details.

specifications:

- Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T)
- 512 MB of RAM (DDR3)
- 256 MB of Flash (NAND)
- 4T4R 2.4/5 GHz Wlan (QCA9980)
- 5x 10/100/1000 Mbps Ethernet
- 10x LEDs, 8x keys (6x buttons, 2x slide-switches)
- 2x USB 3.0 Type-A
- 12VDC/4A AC Adapter
- UART through-hole on PCB
  - J3: Vcc, GND, TX, RX from USB port side
  - 115200n8

Boot instructions for the initramfs image:

1. Prepare the TFTP server with the initramfs image renamed to
   "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10".
2. Press the "AOSS" button while powering on the WXR-2533DHP.
3. Wait until the "Wireless" LED flashes before releasing the AOSS button.
   The WXR-2533DHP will grab the image from TFTP server and will boot it.

Flashing instructions:

To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to
let it finish the flashing process.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
2019-01-01 16:39:59 +01:00
Stefan Lippers-Hollmann
6b63595fec ipq806x: drop kernel/ rootfs partition images for the ZyXEL NBG6817
Since commit 8e9a59a6b9 (build: add
mkrasimage) a proper factory image can be provided for the ZyXEL
NBG6817, which can be flashed from the OEM firmware or used for
tftp based push-button recovery, therefore the previously used
partition images for mmcblk0p5-rootfs.bin and mmcblk0p4-kernel.bin
are no longer required (and using them properly has always been
slightly difficult and risky) and can now be dropped from the image
generation code.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-12-17 00:21:34 +01:00
Ram Chandra Jangir
dc6af37544 ipq806x: Add support for IPQ8064 AP161 board
Specification:
   - SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU
   - RAM: 512MB DDR3 System Memory
   - NOR Flash: 32MB SPI NOR
   - NAND Flash: 256MB NAND
   - Ethernet: 5 x 1G via QCA8337N
   - USB: 2 x USB 3.0 SuperSpeed
   - PCIe: 3x Mini PCIe 2.0 Slots
	   Three PCIE2.0 connectors can connect two or three radio cards
           such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN

 How to flash via u-boot console:
   tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin
   nand erase  0x1340000 0x4000000
   nand write  0x44000000 0x1340000 $filesize
   setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’
   saveenv
   bootm

 Further upgrades via sysupgrade.

 Tested on IPQ8064 AP161 Board:
   1) NAND boot
   2) Tested USB and PCIe interfaces
   3) WDOG test
   4) cpu frequency scaling
   5) ethernet, 2G and 5G WiFi
   6) ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-11-26 12:05:46 +01:00
John Crispin
61b5b4971e mac80211: make ath10k-ct the default ath10k
We select ath10k-ct by default, but it is still possible to build
the upstream version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
2018-09-26 16:39:44 +02:00
David Bauer
8e9a59a6b9 build: add mkrasimage
The current make-ras.sh image generation script for the ZyXEL NBG6617
has portability issues with bash. Because of this, factory images are
currently not built correctly by the OpenWRT buildbots.

This commit replaces the make-ras.sh by C-written mkrasimage.

The new mkrasimage is also compatible with other ZyXEL devices using
the ras image-format.
This is not tested with the NBG6616 but it correctly builds the
header for ZyXEL factory image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-28 11:26:53 +02:00
INAGAKI Hiroshi
4645a6d318 ipq806x: add support for NEC Aterm WG2600HP
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

Specification:

- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
  - RX, TX, NC, GND, Vcc from power connector side
  - baudrate: 115200 bps

Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
  /dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
  fw_setenv ipaddr "192.168.0.1"
  fw_setenv serverip "192.168.0.2"
  fw_setenv autostart "yes"
  fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
  bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:01 +02:00
Stefan Lippers-Hollmann
05f53eecca ipq806x: define KERNEL_SIZE in KB instead of byte for the image generation
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
c3af761e47 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500v2
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500v2.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
c228bbe616 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
45b8a7c1a6 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 D7800
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 D7800.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Tathagata Das <tathagata@alumnux.com>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
0c967d92b3 ipq806x: increase kernel partition size for the TP-Link Archer VR2600v
The default image does not fit 2 MB anymore, expand kernel partition
to 3 MB.

Upgrading should work transparently via sysupgrade in both directions.
Another option would be to merge "kernel" and "rootfs" into a single
"firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the
sizes of the existing partitioning has been deemed safer in the absence
of an actual runtime test on an affected device; the maximum for rootfs
changes from 10.4 MB to 9.4 MB.

This change follows the example for the TP-Link Archer C2600, but has
not been runtime tested on a TP-Link Archer VR2600v.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Sebastian Quilitz <zeraphim@x-pantion.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
dc50694bd1 ipq806x: increase kernel partition size for the Netgear r7800
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This patch is based on a corresponding change by Pavel Kubelun
<be.dissent@gmail.com> and has been tested by Michael Yartys
<michael.yartys@protonmail.com>

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Mathias Kresin
74a0d8cd92 build: consolidate fake uImage header build commands
Merge the two existing functions and use a parameter for the type
header field.

It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-20 20:58:52 +02:00
Christian Mehlis
0c7e78930b ipq806x: add support for Compex WPQ864
Hardware highlights:
- SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU
- RAM: (512MB or 1GB) DDR3 System Memory
- Storage: 32MB NOR (Cypress S25FL256S1)
           256MB NAND (Micron MT29F2G08ABBEAH4)
- Ethernet: 5 x 1G via QCA8337N
- USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket
- PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared)
- SIM Card Slot: 2 x Slot
- Buttons: Reset Button
- LEDs: 18x, 8x GPIO controllable
- Buzzer

The correct amount of RAM will be passed by the bootloader.

In contrast to the documentation provided by Compex, the third PCIe
doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST
for PCIe0 and PCIe2.

So far, no one was able to get USB 3.0 working with the 1GB RAM version,
while it works fine for my 512MB version. Since USB 3.0 doesn't work with
the Compex firmware for the 1G variant either, it could be a hardware
issue with these boards.

OpenWrt will be installed to the NAND flash. Make sure to have a full
working image on the NOR flash. It will be the backup in case anything
goes wrong.

It has been observed that an image loaded via tftpboot might have
bitflips. Hence the extra step to create a crc32 checksum to allow to
compare the checksum with the one from the source file prior to flashing.

In all cases it is necessary to set the following u-boot parameter to an
empty (whitespace) value, to ensure that the chosen bootargs of the dts
isn't overwritten or set to bogus - not working - values:

  (IPQ) # set bootargs " "
  (IPQ) # set fsbootargs " "
  (IPQ) # saveenv

The sysupgrade image can be installed directly on flash using u-boot (put
jumper in JP13 (leave JP9 open) to boot from nand):

  (IPQ) # set serverip 192.168.1.20
  (IPQ) # set ipaddr 192.168.1.1

  (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin
  (IPQ) # crc32 0x42000000 $filesize

  (IPQ) # nand erase 0x1340000 0x4000000
  (IPQ) # nand write 0x42000000 0x1340000 $filesize

The initramfs image can be started using:

  (IPQ) # set fdt_high 0x48000000
  (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb
  (IPQ) # bootm 0x44000000

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-15 08:17:10 +01:00
John Crispin
b7f115f22a ipq806x: drop ipq40xx support
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
Dongming Han
04d3308b62 ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2018-02-14 09:40:32 +01:00
Sven Eckelmann
25a72f5a01 ipq-wifi: drop OpenMesh A42 board-2.bin
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.

[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-02-11 16:33:00 +01:00
Christian Lamparter
5988364cf3 ipq806x: remove dependency on non-existent kmod
During the integration of the ipq40xx target,
the phy drivers were included into the ipq806x's
target kernel config.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter
51dd8f3875 ipq-wifi: align AVM FRITZ!Box 4040's board-2.bin package
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Mathias Kresin
16f2befc3c ipq806x: drop ubifs support
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin
0af5e9bdc4 ipq806x: drop legacy image leftovers
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin
52e7df3f49 ipq806x: unset filesystem specific build command by default
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.

The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.

Fixes: FS#1276

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin
f319c5c254 ipq806x: remove unnecessary filesystem specific build
The Openmesh factory image doesn't need a squashfs specific build command.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin
f2a8e02134 ipq806x: use bin file extension for sysupgrade-tar images
Use the file extension bin for sysupgrade-tar images to unify the file
extension across the target/tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Sven Eckelmann
86e18f6706 ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
  - 802.3af POE on Ethernet 1
  - 18-24v passive POE (mode B) on Ethernet 2

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 08:00:14 +01:00
Luis Araneda
7293499f71 ipq806x: Sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda
33f09cf151 ipq806x: convert to dt-based board-detection
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree

Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script

Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda
3cbdae2421 ipq806x: sync image filename with dt compatible string
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:02 +01:00
Luis Araneda
575178e462 treewide: add only one device when appending to TARGET_DEVICES
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-12 18:47:26 +01:00
Roman Yeryomin
156f2df879 ipq806x: ipq4019: add ap-dk01.1-c1 board support
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)

First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize

Further upgrades via sysupgrade.

Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition

Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.

Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.

Changes since v2:
- based on dts(i) rework/cleanup submitted:
  http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:24:26 +02:00
Stefan Lippers-Hollmann
6e6d4f2e87 ipq806x: nbg6817: add kmod-fs-ext4 to device packages
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.

/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)

Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile  emergency overlay in place.

Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-11-03 20:04:51 +01:00
Jonas Gorski
6f528dfbd9 treewide: do not use IMG_PREFIX in Image/Prepare
IMG_PREFIX can be modified in ImageBuilder by passing EXTRA_IMAGE_NAME
on command line, but Image/Prepare is not run in ImageBuilder. This
causes missing files when IMG_PREFIX is used for target file names in
Image/Prepare, then as source file names in Image/BuildKernel or
Image/Build.

Fix this by using a fixed output file name in Image/Prepare, and copy to
the expected file name in Image/BuildKernel instead, which is run by
ImageBuilder.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-10-26 12:26:25 +02:00
Ram Chandra Jangir
c2a4f144d7 ipq806x: Enable AP148 fit image(.itb) generation
This change enables .itb image generation for AP148,
It will help us to boot and test AP148 with NOR flash.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-07-06 07:16:40 +02:00
Piotr Dymacz
7d6c63d875 build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Ram Chandra Jangir
e178d51a04 ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 board
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.

Testing:
 *Tested on IPQ40xx AP-DK04.1-C1:
   a. NAND boot
   b. ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-06-07 06:33:33 +02:00
Mathias Kresin
8b3fa168b4 firmware: rework fritz-tools package
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.

Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.

Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.

Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-08 14:30:00 +02:00
Mathias Kresin
86a0cbb333 treewide: select ath10k firmware explicit
Do not rely on the default firmware selected by ath10k.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
Thomas Reifferscheid
b69807e2b2 ipq806x: fix Netgear X4 R7500 ath10k firmware selection
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-03-24 08:09:39 +01:00
Christian Lamparter
1cb406d019 ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB Nanya NT5CC128M16IP
FLASH:	32 MiB MXIC MX25L25635FMI
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
	1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:	Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one WLAN and one WPS button
LEDS:	Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1. The SoC's serial port is right
	next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
	header for it. Use a multimeter to figure out the pinout!

This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.

Install Procedure:
 0. It's highly recommended to connect to the serial port.
    The serial settings are listed above.
 1. install a u-boot image for AVM Fritz!Box 4040
    (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
    <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
 2. upload the initramfs.itb image via tftp (u-boot listens to
    192.168.1.1 - use binary transfer mode!)
 3. connect to the FB4040 and use sysupgrade sysupgrade.bin
    to install the image.

Works:
	- Switch and Ethernet (99%)
        - Buttons (WLAN, WPS)
        - FLASH (1 x 32MiB NOR Chip)
        - WLAN2G and WLAN5G
        - CPUFREQ scaling
        - PRNG
        - serial
        - Crypto Accelerator
        - sysupgrade (Read the flash instructions to avoid bricking)
        - full LEDE Install (Read the flash instructions to avoid bricking)
	- LEDs (Power, WAN, Info (red and amber), LAN)
          The LEDs are connected to the QCA8075 LED ports.
	  The AR40xx driver contains a gpio-controller to
	  handle these special "GPIOs".
        - USB Both 3.0 and 2.0 ports
        - many packages from other ARMv7 boards
          (This does include the RaspberryPi Model 2!)
        - ...

Not planned:
	- WAN<->LAN short-cut
	- Qualcomm Secure Execution Environment
        - ...

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Thomas Reifferscheid
eb09d79c16 ipq806x: sanitize Dni image generation
The more straight forward approach for generating the pure and unpadded
kernel file which then can be used for initramfs straight.
Build options for factory.img and sysupgrade.tar are handeled
seperately.

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-02-26 13:32:26 +01:00
Thomas Reifferscheid
e01b034cdc ipq806x: fix fakerootfs position
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.

Fixes: FS#542

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-02-21 21:18:33 +01:00
Joseph C. Lehner
7d00cfe9bb build: centralize fakeroot code
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.

Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Joseph C. Lehner
aeba0fe466 build: move append-file to image-commands.mk
Move it append-file to image-commands.mk so that it can used by other
targets as well.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-01-27 11:10:10 +01:00
Sebastian Quilitz
ae79c41286 ipq806x: add support for TP-Link Archer VR2600v
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
2016-11-24 22:37:40 +01:00
Felix Fietkau
9d6d7d9a0e ipq806x: append metadata to images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Felix Fietkau
3616666126 ipq806x: fix zyxel image build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
André Valentin
a0ed7af6c6 ipq806x/nbg6817: add support for ZyXEL NBG6817
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:46 +02:00
Felix Fietkau
a92f57599c ipq806x: add back end-of-UBI marker for a few factory images (FS#228)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-18 09:30:57 +02:00