Seemingly unneeded based on new upstream code so manually deleted:
layerscape:
820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack:
251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All modifications made by update_kernel.sh/no manual intervention needed
Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64
No dmesg regressions, everything appears functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add run test from PR]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the Edgecore ECW5410 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.
Installation instructions:
Through stock firmware or initramfs.
1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>
This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0
Note
Initramfs:
1. Connect to console
2. Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1
You need to interrupt the bootloader after rebooting and run:
run altbootcmd
This will switch your active rootfs partition to one you wrote to and boot from it.
So if rootfs1 is active, then it will change it to rootfs2.
This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.
5. Transfer sysupgrade image
6. Flash with sysupgrade -n.
Note that sysupgrade will write the image to rootfs partition that is not currently in use.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This imports the patch that adds bootargs-append support from IPQ40xx.
This way we can append additional boot arguments from DTS instead of only being able to overwrite them.
This way dual firmware devices can use the rootfs number that bootloader passes to decide from what to boot.
But we still need to append console info and ubi root info.
This is used by Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQ806x series also has a GSBI1 with UART and I2C peripherals, so lets add the node for it.
Its needed for Edgecore ECW5410 which uses the UART from GSBI1 as second UART for Bluetooth.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Manually merged:
hack-5.4
230-openwrt_lzma_options.patch
bcm27xx
950-0283-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch
x86
011-tune_lzma_options.patch
Remove upstreamed patches in collaboration with Ansuel Smith:
ipq806x
093-1-v5.8-ipq806x-PCI-qcom-Add-missing-ipq806x-clocks-in-PCIe-driver.patch
093-2-v5.8-ipq806x-PCI-qcom-Change-duplicate-PCI-reset-to-phy-reset.patch
093-3-v5.8-ipq806x-PCI-qcom-Add-missing-reset-for-ipq806x.patch
All other modifications made by update_kernel.sh
Build-tested: bcm27xx/bcm2708, ipq806x, x86/64
Run-tested: ipq806x (R7800), x86/64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[update commit message/tested]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Changes:
- Update patches
- Update dts with new binding
Tx term offset dropped and replaced with a new compatible
Removed:
- 0071-5-PCI-qcom-Programming-the-PCIE-iATU-for-IPQ806x
Pci init does the same exact thing (was needed in older kernel version)
- 0071-7-pcie-Set-PCIE-MRRS-and-MPS-to-256B
Rejected upstream, can't find any reason to have this. No regression with
testing it on R7800.
Tested on R7800 (ipq8065), R7500 v2 ("ipq8064-v2")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
[rebase and refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- Replace nvmem qcom patch with upstream version
- Update compatible
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches, minor commit message rewording]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
Replace all the custom patches with the backported upstream version
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches
instead of keeping a local version. As a consequence:
- we use a part of the shared definitions there and update device
DTS files accordingly
- we move additional stuff from our local v1.0.dtsi to the patch
- we drop partitions, LEDs and keys from the file as we will
implement them differently anyway
Like with the previous patch, this follows the idea that a diff
from upstream might be easier to handle than a big file of our
own with different distribution pattern of properties.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite
it with a full version of our own in the ipq806x target. About half of
the contents of our file are upstream content, the other half are local
improvements.
To prevent us from having a lot of code maintained twice in parallel,
this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our
local changes are arranged into three patches, the first pulling a
commit from upstream, the second doing a few small adjustments, and
the third adding all additional stuff.
This should get us the best of both worlds.
The property "ports-implemented" on sata@29000000 is moved to
2nd-level DTSI files as kernel defines it there as well.
While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to
include the kernel version where it's added upstream.
Even though this might look more complicated in the first place,
the aim is to bring our files closer to upstream, so we can benefit
from changes directly and vice-versa. After all, this drop about
650 lines just copied from the upstream DTSI file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the Linksys EA7500 V1 router.
Specification:
- CPU: Qualcomm IPQ8064
- RAM: 256MB
- Flash: NAND 128MB
- WiFi: QCA9982 an+ac + QCA9983 bgn
- Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
- USB: 1x USB 3.0 1x USB2.0
- Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
- 2 Buttons
- 1 LED
Known issues:
- Some devices won't flash via web gui
Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.
Serial + TFTP method:
- downgrade to 1.1.2 two times
- connect ehternet and serial cable
- set ip address of tftp server to 192.168.1.254
- put openwrt factory image to tftp folder and rename it to macan.bin
- stop device while booting in u-boot
- run command: "run flashimg"
- run command: "setenv boot_part 1"
- run command "saveenv"
- reset
Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F
Tested by github users: @jack338c and @grzesiczek1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between 4.19 and 5.4, the kernel moved the partition parsers into
the parsers subdirectory. This led to some necessary rebasing of
our local patches for parsers, which partially has been performed
without caring about where the code was inserted.
This commit tries to adjust our local patches so that parsers are
inserted at the "proper" positions with respect to alphabetic sorting
(if possible). Thus, the commit is cosmetic.
While this might look useless now, it will make life easier when
adding other parsers in the future or for rebasing on kernel changes.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Due to changes in syscon driver, the phy dwc3 driver
needs to use device_node_to_regmap since it has to skip
the new introduced clk check. This fix broken usb3 on this
target.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Currently the watchdog timer is broken as it tries to
get an interrupt to setup pretimeout. Since our platform
have a different type of interrupt disable it and use
legacy watchdog probe.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This was created by Chunkeey some time ago. Since mdio driver
works or doesn't work and since this was tested by me for 1 year,
include it to remove the use of the generic bitbang gpio driver for
switch driver.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework tsens driver.
Since in the new kernel 5.4 init common do more than it
should, inizialize the kernel memory directly in the driver and
drop use of this function. Rework all the patch with the new
variable names.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework l2 scaling patch to fix some compile warning
and to imporve the caling timings by removing call to unnecessary
function.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
