Commit Graph

7 Commits

Author SHA1 Message Date
David Bauer
3364af629d ath79: fix OCEDO Raccoon 10Mbit PLL value
This corrects the PLL value for 10 Mbit/s links on the OCEDO Raccoon.
Prior to this patch, 10 Mbit/s links would not transmit data.

It is worth mentioning that the vendor firmware used the same PLL
settings and 10Mbit/s was also not working there.

All other link-modes are working correctly without any packet loss.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-05-05 21:11:01 +02:00
Petr Štetiar
0d23fd2ab2 treewide: dts: Remove default-state=off property from all gpio LED nodes
>From the Documentation/devicetree/bindings/leds/common.txt:

- default-state : The initial state of the LED. Valid values are "on", "off",
  and "keep". If the LED is already on or off and the default-state property is
  set the to same value, then no glitch should be produced where the LED
  momentarily turns off (or on). The "keep" setting will keep the LED at
  whatever its current state is, without producing a glitch.  The default is
  off if this property is not present.

So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:16:28 +01:00
David Bauer
df2e6b64d1 ath79: add firmware partition compatible for OCEDO
This commit adds firmware partition compatible for the
OCEDO Raccoon and OCEDO Koala.

Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 21:26:56 +01:00
Dmitry Tunin
7a873974f7 ath79: add support for indicating the boot state using multiple leds
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00
Mathias Kresin
55ff2951ea ath79: fix dts warnings
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
David Bauer
5409dcffbd ath79: fix OCEDO Raccoon
The OCEDO Raccoon only has one ethernet port, but currently uci sections
for WAN and LAN are created.

Additionally, newer versions of the devices U-Boot (units with SteelWRT)
set the kernel-cmdline and therefore overwrite the partition-layout.
We fix this by overwriting the cmdline supplied by the bootloader.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-07-25 08:59:33 +02:00
David Bauer
6476148034 ath79: add support for OCEDO Raccoon
This commit adds support for the OCEDO Raccoon

SOC:	Atheros AR9344
RAM:    128MB
FLASH:  16MiB
WLAN1:  AR9344 2.4 GHz 802.11bgn 2x2
WLAN2:  AR9382 5 GHz 802.11an 2x2
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

	NOTE: The U-Boot won't boot with the serial attached.
	Boot the device without serial attached and attach it
	after 3 seconds.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-07-08 00:04:27 +02:00