4b31717fb0
The RTL8231 is an external chip, and not part of the SoC. That means it is more appropriate to define it in the board specific (base) files, instead of the DT include for the SoC itself. Moving the RTL8231 definition also ensures that boards with no GPIO expander, or an alternative one, don't have a useless gpio1 node label defined. Tested on a Netgear GS110TPPv1. Signed-off-by: Sander Vanheule <sander@svanheule.net>
150 lines
2.5 KiB
Plaintext
150 lines
2.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#include "rtl838x.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_sys;
|
|
led-failsafe = &led_sys;
|
|
led-running = &led_sys;
|
|
led-upgrade = &led_sys;
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinmux_disable_sys_led>;
|
|
compatible = "gpio-leds";
|
|
|
|
led_sys: sys {
|
|
label = "green:sys";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
gpio1: rtl8231-gpio {
|
|
compatible = "realtek,rtl8231-gpio";
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
indirect-access-bus-id = <0>;
|
|
|
|
poe_enable {
|
|
gpio-hog;
|
|
gpios = <13 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x40000>;
|
|
read-only;
|
|
};
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
partition@50000 {
|
|
label = "u-boot-env2";
|
|
reg = <0x50000 0x10000>;
|
|
};
|
|
partition@60000 {
|
|
label = "jffs";
|
|
reg = <0x60000 0x100000>;
|
|
};
|
|
partition@160000 {
|
|
label = "jffs2";
|
|
reg = <0x160000 0x100000>;
|
|
};
|
|
partition@b260000 {
|
|
label = "firmware";
|
|
reg = <0x260000 0x6d0000>;
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
openwrt,ih-magic = <0x83800000>;
|
|
};
|
|
partition@930000 {
|
|
label = "runtime2";
|
|
reg = <0x930000 0x6d0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
mdio: mdio-bus {
|
|
compatible = "realtek,rtl838x-mdio";
|
|
regmap = <ðernet0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
INTERNAL_PHY(8)
|
|
INTERNAL_PHY(9)
|
|
INTERNAL_PHY(10)
|
|
INTERNAL_PHY(11)
|
|
INTERNAL_PHY(12)
|
|
INTERNAL_PHY(13)
|
|
INTERNAL_PHY(14)
|
|
INTERNAL_PHY(15)
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
SWITCH_PORT(8, 1, internal)
|
|
SWITCH_PORT(9, 2, internal)
|
|
SWITCH_PORT(10, 3, internal)
|
|
SWITCH_PORT(11, 4, internal)
|
|
SWITCH_PORT(12, 5, internal)
|
|
SWITCH_PORT(13, 6, internal)
|
|
SWITCH_PORT(14, 7, internal)
|
|
SWITCH_PORT(15, 8, internal)
|
|
|
|
port@28 {
|
|
ethernet = <ðernet0>;
|
|
reg = <28>;
|
|
phy-mode = "internal";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|