3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
184 lines
3.0 KiB
Plaintext
184 lines
3.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar7240.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "buffalo,whr-g301n", "qca,ar7240";
|
|
model = "Buffalo WHR-G301N";
|
|
|
|
aliases {
|
|
led-boot = &led_diag;
|
|
led-failsafe = &led_diag;
|
|
led-upgrade = &led_diag;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
router_on {
|
|
label = "router_on";
|
|
linux,code = <BTN_2>;
|
|
linux,input-type = <EV_SW>;
|
|
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
router_off {
|
|
label = "router_off";
|
|
linux,code = <BTN_3>;
|
|
linux,input-type = <EV_SW>;
|
|
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&switch_led_pins>;
|
|
|
|
security {
|
|
label = "orange:security";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_diag: diag {
|
|
label = "red:diag";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
router {
|
|
label = "green:router";
|
|
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan1 {
|
|
label = "green:lan1";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan2 {
|
|
label = "green:lan2";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan3 {
|
|
label = "green:lan3";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan4 {
|
|
label = "green:lan4";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "green:wan";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
ath9k-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan {
|
|
label = "green:wlan";
|
|
gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x3e000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
partition@3e000 {
|
|
reg = <0x3e000 0x2000>;
|
|
label = "u-boot-env";
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
compatible = "denx,uimage";
|
|
reg = <0x40000 0x3a0000>;
|
|
label = "firmware";
|
|
};
|
|
|
|
partition@3e0000 {
|
|
reg = <0x3e0000 0x10000>;
|
|
label = "user_property";
|
|
read-only;
|
|
};
|
|
|
|
art: partition@3f0000 {
|
|
reg = <0x3f0000 0x10000>;
|
|
label = "art";
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
mtd-mac-address = <&art 0x120c>;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x120c>;
|
|
mtd-mac-address-increment = <1>;
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
ath9k: wifi@0,0 {
|
|
compatible = "pci168c,002a";
|
|
reg = <0x0000 0 0 0 0>;
|
|
qca,no-eeprom;
|
|
mtd-mac-address = <&art 0x120c>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
};
|
|
};
|
|
|
|
&pinmux {
|
|
switch_led_pins: switch_led_pins {
|
|
pinctrl-single,bits = <0x0 0x0 0xf8>;
|
|
};
|
|
};
|