4e46ae1f69
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6282 (1.6 GHz)
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 1x USB 2.0
- 2x USB 3.0
- 2x SATA
- 3x button
- 5x leds
- serial on J5 connector accessible from rear panel
(115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)
Installation by USB + serial:
- Copy initramfs image to fat32 usb drive
- Connect pendrive to USB 2.0 front socket
- Connect serial console
- Stop booting in u-boot
- Do:
usb reset
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Installation by TFTP + serial:
- Setup TFTP server and copy initramfs image
- Connect serial console
- Stop booting in u-boot
- Do:
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Known issues:
- Power button and PHY INTn pin are connected to the same GPIO. It
causes that every network restart button is pressed in system.
As workaround, button is used as regular BTN_1.
For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
298 lines
8.6 KiB
Makefile
298 lines
8.6 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0-only
|
|
#
|
|
# Copyright (C) 2009-2013 OpenWrt.org
|
|
|
|
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
KERNEL_LOADADDR:=0x8000
|
|
|
|
# Some info about Ctera firmware:
|
|
# 1. It's simple tar file (GNU standard), but it must have ".firm" suffix.
|
|
# 2. It contains two images: kernel and romdisk. Both are required.
|
|
# 3. Every image has header and trailer file.
|
|
# 4. The struct of tar firmware is: header kernel trailer header romdisk trailer
|
|
# 5. In header file are some strings used to describe image. It was decoded from
|
|
# factory image.
|
|
# 6. Version format in header file is restricted by Original FW.
|
|
# 7. Trailer file contains MD5 sum string of header and image file.
|
|
# 8. Firmware file must have <=24MB size.
|
|
|
|
define Build/ctera-firmware
|
|
mkdir -p $@.tmp
|
|
|
|
# Prepare header and trailer file for kernel
|
|
echo "# CTera firmware information file" > $@.tmp/header
|
|
echo "image_type=kernel" >> $@.tmp/header
|
|
echo "arch=Kirkwood" >> $@.tmp/header
|
|
echo "board=Any" >> $@.tmp/header
|
|
echo "version=3.1.22.30669" >> $@.tmp/header
|
|
echo "kernel_cmd=console=ttyS0,115200 earlyprintk" >> $@.tmp/header
|
|
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
|
|
>> $@.tmp/header
|
|
|
|
cp $@ $@.tmp/kernel
|
|
|
|
echo "MD5=$$(cat $@.tmp/header $@.tmp/kernel | $(MKHASH) md5)" \
|
|
> $@.tmp/trailer
|
|
|
|
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
|
-H gnu -C $@.tmp -cf $@.tar header kernel trailer
|
|
|
|
# Prepare header and trailer file for fake romdisk
|
|
echo "# CTera firmware information file" > $@.tmp/header
|
|
echo "image_type=romdisk" >> $@.tmp/header
|
|
echo "initrd=yes" >> $@.tmp/header
|
|
echo "arch=Kirkwood" >> $@.tmp/header
|
|
echo "board=Any" >> $@.tmp/header
|
|
echo "version=3.1.22.30669" >> $@.tmp/header
|
|
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
|
|
>> $@.tmp/header
|
|
|
|
rm -f $@
|
|
touch $@
|
|
$(call Build/append-uImage-fakehdr, ramdisk)
|
|
cp $@ $@.tmp/romdisk
|
|
|
|
echo "MD5=$$(cat $@.tmp/header $@.tmp/romdisk | $(MKHASH) md5)" \
|
|
> $@.tmp/trailer
|
|
|
|
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
|
-H gnu -C $@.tmp -rf $@.tar header romdisk trailer
|
|
|
|
mv $@.tar $@
|
|
rm -rf $@.tmp
|
|
endef
|
|
|
|
define Device/kernel-size-migration
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Partition design has changed compared to \
|
|
older versions (up to 21.02) due to kernel size restrictions. \
|
|
Upgrade via sysupgrade mechanism is not possible, so new \
|
|
installation via factory style image is required.
|
|
endef
|
|
|
|
define Device/Default
|
|
PROFILES := Default
|
|
DEVICE_DTS = kirkwood-$(lastword $(subst _, ,$(1)))
|
|
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
|
KERNEL := kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL_IN_UBI := 1
|
|
|
|
PAGESIZE := 2048
|
|
SUBPAGESIZE := 512
|
|
BLOCKSIZE := 128k
|
|
IMAGES := sysupgrade.bin factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-ubi
|
|
endef
|
|
|
|
define Device/checkpoint_l-50
|
|
DEVICE_VENDOR := Check Point
|
|
DEVICE_MODEL := L-50
|
|
DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \
|
|
kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic-wolfssl
|
|
IMAGES := sysupgrade.bin
|
|
endef
|
|
TARGET_DEVICES += checkpoint_l-50
|
|
|
|
define Device/cisco_on100
|
|
DEVICE_VENDOR := Cisco Systems
|
|
DEVICE_MODEL := ON100
|
|
KERNEL_SIZE := 5376k
|
|
KERNEL_IN_UBI :=
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
DEVICE_PACKAGES := kmod-mvsdio
|
|
SUPPORTED_DEVICES += on100
|
|
endef
|
|
TARGET_DEVICES += cisco_on100
|
|
|
|
define Device/cloudengines_pogoe02
|
|
DEVICE_VENDOR := Cloud Engines
|
|
DEVICE_MODEL := Pogoplug E02
|
|
DEVICE_DTS := kirkwood-pogo_e02
|
|
SUPPORTED_DEVICES += pogo_e02
|
|
endef
|
|
TARGET_DEVICES += cloudengines_pogoe02
|
|
|
|
define Device/cloudengines_pogoplugv4
|
|
DEVICE_VENDOR := Cloud Engines
|
|
DEVICE_MODEL := Pogoplug V4
|
|
DEVICE_DTS := kirkwood-pogoplug-series-4
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-mvsdio kmod-usb3 \
|
|
kmod-gpio-button-hotplug
|
|
endef
|
|
TARGET_DEVICES += cloudengines_pogoplugv4
|
|
|
|
define Device/ctera_c200-v1
|
|
DEVICE_VENDOR := Ctera
|
|
DEVICE_MODEL := C200
|
|
DEVICE_VARIANT := V1
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-gpio-button-hotplug \
|
|
kmod-hwmon-lm63 kmod-rtc-s35390a kmod-usb-ledtrig-usbport
|
|
KERNEL := kernel-bin | append-dtb | uImage none | ctera-firmware
|
|
KERNEL_IN_UBI :=
|
|
KERNEL_SUFFIX := -factory.firm
|
|
IMAGES := sysupgrade.bin
|
|
endef
|
|
TARGET_DEVICES += ctera_c200-v1
|
|
|
|
define Device/globalscale_sheevaplug
|
|
DEVICE_VENDOR := Globalscale
|
|
DEVICE_MODEL := Sheevaplug
|
|
DEVICE_PACKAGES := kmod-mvsdio
|
|
endef
|
|
TARGET_DEVICES += globalscale_sheevaplug
|
|
|
|
define Device/iom_iconnect-1.1
|
|
DEVICE_VENDOR := Iomega
|
|
DEVICE_MODEL := Iconnect
|
|
DEVICE_DTS := kirkwood-iconnect
|
|
SUPPORTED_DEVICES += iconnect
|
|
endef
|
|
TARGET_DEVICES += iom_iconnect-1.1
|
|
|
|
define Device/iom_ix2-200
|
|
DEVICE_VENDOR := Iomega
|
|
DEVICE_MODEL := StorCenter ix2-200
|
|
DEVICE_DTS := kirkwood-iomega_ix2_200
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
|
|
kmod-gpio-button-hotplug kmod-hwmon-lm63
|
|
PAGESIZE := 512
|
|
SUBPAGESIZE := 256
|
|
BLOCKSIZE := 16k
|
|
KERNEL_SIZE := 3072k
|
|
KERNEL_IN_UBI :=
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 31744k
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += iom_ix2-200
|
|
|
|
define Device/linksys
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_PACKAGES := kmod-mwl8k wpad-basic-wolfssl kmod-gpio-button-hotplug
|
|
KERNEL_IN_UBI :=
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
endef
|
|
|
|
define Device/linksys_e4200-v2
|
|
$(Device/linksys)
|
|
$(Device/kernel-size-migration)
|
|
DEVICE_MODEL := E4200
|
|
DEVICE_VARIANT := v2
|
|
KERNEL_SIZE := 3072k
|
|
SUPPORTED_DEVICES += linksys,viper linksys-viper
|
|
endef
|
|
TARGET_DEVICES += linksys_e4200-v2
|
|
|
|
define Device/linksys_ea3500
|
|
$(Device/linksys)
|
|
$(Device/kernel-size-migration)
|
|
DEVICE_MODEL := EA3500
|
|
PAGESIZE := 512
|
|
SUBPAGESIZE := 256
|
|
BLOCKSIZE := 16k
|
|
KERNEL_SIZE := 3072k
|
|
SUPPORTED_DEVICES += linksys,audi linksys-audi
|
|
endef
|
|
TARGET_DEVICES += linksys_ea3500
|
|
|
|
define Device/linksys_ea4500
|
|
$(Device/linksys)
|
|
$(Device/kernel-size-migration)
|
|
DEVICE_MODEL := EA4500
|
|
KERNEL_SIZE := 3072k
|
|
SUPPORTED_DEVICES += linksys,viper linksys-viper
|
|
endef
|
|
TARGET_DEVICES += linksys_ea4500
|
|
|
|
define Device/netgear_readynas-duo-v2
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := ReadyNAS Duo
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_DTS := kirkwood-netgear_readynas_duo_v2
|
|
KERNEL_IN_UBI :=
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
|
|
kmod-gpio-button-hotplug kmod-hwmon-g762 kmod-rtc-rs5c372a kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += netgear_readynas-duo-v2
|
|
|
|
define Device/raidsonic_ib-nas62x0
|
|
DEVICE_VENDOR := RaidSonic
|
|
DEVICE_MODEL := ICY BOX IB-NAS62x0
|
|
DEVICE_DTS := kirkwood-ib62x0
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
|
|
SUPPORTED_DEVICES += ib62x0
|
|
endef
|
|
TARGET_DEVICES += raidsonic_ib-nas62x0
|
|
|
|
define Device/seagate_blackarmor-nas220
|
|
DEVICE_VENDOR := Seagate
|
|
DEVICE_MODEL := Blackarmor NAS220
|
|
DEVICE_PACKAGES := kmod-hwmon-adt7475 kmod-fs-ext4 kmod-ata-marvell-sata \
|
|
mdadm kmod-gpio-button-hotplug
|
|
PAGESIZE := 512
|
|
SUBPAGESIZE := 256
|
|
BLOCKSIZE := 16k
|
|
UBINIZE_OPTS := -e 1
|
|
endef
|
|
TARGET_DEVICES += seagate_blackarmor-nas220
|
|
|
|
define Device/seagate_dockstar
|
|
DEVICE_VENDOR := Seagate
|
|
DEVICE_MODEL := FreeAgent Dockstar
|
|
SUPPORTED_DEVICES += dockstar
|
|
endef
|
|
TARGET_DEVICES += seagate_dockstar
|
|
|
|
define Device/seagate_goflexnet
|
|
DEVICE_VENDOR := Seagate
|
|
DEVICE_MODEL := GoFlexNet
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
|
|
SUPPORTED_DEVICES += goflexnet
|
|
endef
|
|
TARGET_DEVICES += seagate_goflexnet
|
|
|
|
define Device/seagate_goflexhome
|
|
DEVICE_VENDOR := Seagate
|
|
DEVICE_MODEL := GoFlexHome
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
|
|
SUPPORTED_DEVICES += goflexhome
|
|
endef
|
|
TARGET_DEVICES += seagate_goflexhome
|
|
|
|
define Device/zyxel_nsa310b
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NSA310b
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-r8169 kmod-fs-ext4 \
|
|
kmod-gpio-button-hotplug kmod-hwmon-lm85
|
|
SUPPORTED_DEVICES += nsa310b
|
|
endef
|
|
TARGET_DEVICES += zyxel_nsa310b
|
|
|
|
define Device/zyxel_nsa310s
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NSA310S
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-gpio-button-hotplug
|
|
endef
|
|
TARGET_DEVICES += zyxel_nsa310s
|
|
|
|
define Device/zyxel_nsa325
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NSA325
|
|
DEVICE_VARIANT := v1/v2
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
|
|
kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
|
|
SUPPORTED_DEVICES += nsa325
|
|
endef
|
|
TARGET_DEVICES += zyxel_nsa325
|
|
|
|
$(eval $(call BuildImage))
|