b4d3110ac1
This ports the GL.iNet 6408/6416 from ar71xx. The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with more DRAM/Flash and console/GPIO header in the same small form-factor. Specifications: - SoC: Atheros AR9331 - CPU: 400 MHz - Flash: 8/16 MiB - RAM: 64 MiB - WiFi: 2.4 GHz b/g/n (SoC) - Ethernet: 2x 100M ports (LAN/WAN) - USB: 1x 2.0 The difference between 6408 and 6416 is just the flash size. It looks like only the 16 MiB version has been advertised, while the 6408 is a modified version. There are also 1-port versions sold by third parties. Installation: Install the sysupgrade image via stock firmware GUI or upload it via uboot (web-based). The device will be available at 192.168.1.1. Attention: In ar71xx, the same board name is used for both flash versions. So, please make sure you flash the correct ath79 image when upgrading. This has been device-tested on a GL.iNet 6416. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
92 lines
1.3 KiB
Plaintext
92 lines
1.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9331.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &uart;
|
|
label-mac-device = &wmac;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan {
|
|
label = "gl-inet:red:wlan";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
lan {
|
|
label = "gl-inet:green:lan";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
reg_usb_vbus: reg_usb_vbus {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "usb_vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <0>;
|
|
switch-phy-swap = <0>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "host";
|
|
vbus-supply = <®_usb_vbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
};
|