tn3399_openwrt/target/linux/ath79/dts/ar7161_dlink_dir-825-b1.dts
Petr Štetiar 0d23fd2ab2 treewide: dts: Remove default-state=off property from all gpio LED nodes
>From the Documentation/devicetree/bindings/leds/common.txt:

- default-state : The initial state of the LED. Valid values are "on", "off",
  and "keep". If the LED is already on or off and the default-state property is
  set the to same value, then no glitch should be produced where the LED
  momentarily turns off (or on). The "keep" setting will keep the LED at
  whatever its current state is, without producing a glitch.  The default is
  off if this property is not present.

So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:16:28 +01:00

242 lines
3.9 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar7100.dtsi"
/ {
compatible = "dlink,dir-825-b1", "qca,ar7161";
model = "D-Link DIR825B1";
aliases {
led-boot = &orange_power;
led-failsafe = &orange_power;
led-running = &blue_power;
led-upgrade = &orange_power;
};
chosen {
bootargs = "console=ttyS0,115200";
};
extosc: ref {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-output-names = "ref";
clock-frequency = <40000000>;
};
leds {
compatible = "gpio-leds";
blue_usb {
label = "d-link:blue:usb";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
trigger-sources = <&usb_ochi_port>, <&usb_echi_port>;
linux,default-trigger = "usbport";
};
orange_power: orange_power {
label = "d-link:orange:power";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
default-state = "on";
};
blue_power: blue_power {
label = "d-link:blue:power";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
};
blue_wps {
label = "d-link:blue:wps";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
orange_planet {
label = "d-link:orange:planet";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
blue_planet {
label = "d-link:blue:planet";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
};
ath9k-leds {
compatible = "gpio-leds";
wlan2g {
label = "d-link:blue:wlan2g";
gpios = <&ath9k0 5 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wlan5g {
label = "d-link:blue:wlan5g";
gpios = <&ath9k1 5 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
rtl8366s {
compatible = "realtek,rtl8366s";
gpio-sda = <&gpio 5 GPIO_ACTIVE_HIGH>;
gpio-sck = <&gpio 7 GPIO_ACTIVE_HIGH>;
realtek,initvals = <0x06 0x0108>;
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
phy-mask = <0x10>;
phy4: ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii";
};
};
};
};
&usb1 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
usb_ochi_port: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&usb2 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
usb_echi_port: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&usb_phy {
status = "okay";
};
&pcie0 {
status = "okay";
ath9k0: wifi@0,11 {
compatible = "pci168c,0029";
reg = <0x8800 0 0 0 0>;
qca,no-eeprom;
#gpio-cells = <2>;
gpio-controller;
};
ath9k1: wifi@0,12 {
compatible = "pci168c,0029";
reg = <0x9000 0 0 0 0>;
qca,no-eeprom;
#gpio-cells = <2>;
gpio-controller;
};
};
&uart {
status = "okay";
};
&pll {
clocks = <&extosc>;
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "config";
reg = <0x040000 0x010000>;
read-only;
};
partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x050000 0x610000>;
};
caldata: partition@60000 {
label = "caldata";
reg = <0x660000 0x010000>;
read-only;
};
partition@670000 {
label = "unknown";
reg = <0x670000 0x190000>;
read-only;
};
};
};
};
&eth0 {
status = "okay";
pll-data = <0x11110000 0x00001099 0x00991099>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
&eth1 {
status = "okay";
pll-data = <0x11110000 0x00001099 0x00991099>;
phy-handle = <&phy4>;
};