be89c9eec4
The DWR-961 A1 Wireless Router is based on the MT7620A SoC. It's a merge of two Amit boards: DWR-960 with ethernet part of Lava LR-25G001. ROMID it's taken from Telenor branded version and it works with tested device. Images from D-Link site for this router are from DWR-953 and it have ROMID DLK6E2424001. I don't know if it's mistake on web-site or if it's will require different image. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612 mpcie card) - 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337) - 2x internal, non-detachable antennas (Wifi 2.4G) - 3x external, detachable antennas (2x LTE, 1x Wifi 5G) - 1x LTE modem cat 6 - UART (J5) header on PCB (57600 8n1) - 13x LED, 2x button - JBOOT bootloader Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
179 lines
2.9 KiB
Plaintext
179 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* D-Link DWR-96x Common Board Description
|
|
* Copyright 2022 Pawel Dembicki <paweldembicki@gmail.com>
|
|
*/
|
|
#include "mt7620a.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/mtd/partitions/uimage.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_status;
|
|
led-failsafe = &led_status;
|
|
led-running = &led_status;
|
|
led-upgrade = &led_status;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status: status {
|
|
label = "green:status";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "green:wan";
|
|
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan {
|
|
label = "green:lan";
|
|
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
sms {
|
|
label = "green:sms";
|
|
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
signal_green {
|
|
label = "green:signal";
|
|
gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
signal_red {
|
|
label = "red:signal";
|
|
gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
4g {
|
|
label = "green:4g";
|
|
gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
3g {
|
|
label = "green:3g";
|
|
gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan5g {
|
|
label = "green:wlan5g";
|
|
gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
wlan2g {
|
|
label = "green:wlan2g";
|
|
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
wifi: wifi@0,0 {
|
|
compatible = "mediatek,mt76";
|
|
reg = <0x0000 0 0 0 0>;
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
nvmem-cells = <&macaddr_config_e50e>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <(2)>;
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "jboot";
|
|
reg = <0x0 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@10000 {
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
openwrt,ih-magic = <IH_MAGIC_OKLI>;
|
|
openwrt,offset = <0x10000>;
|
|
label = "firmware";
|
|
reg = <0x10000 0xfe0000>;
|
|
};
|
|
|
|
config: partition@ff0000 {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
label = "config";
|
|
reg = <0xff0000 0x10000>;
|
|
read-only;
|
|
|
|
macaddr_config_e50e: macaddr@e50e {
|
|
reg = <0xe50e 0x6>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
default {
|
|
groups = "i2c", "wled", "spi refclk", "uartf", "ephy";
|
|
function = "gpio";
|
|
};
|
|
};
|