7ef7dbaf70
This ports the TP-Link TL-WPA8630 v1 from ar71xx to ath79. Specifications: SoC: QCA9563 CPU: 750 MHz Flash/RAM: 8 / 128 MiB Ethernet: 3x 1G ports (QCA8337 switch) WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac (ath10k) Buttons, LEDs and network setup appear to be almost identical to the v2 revision. Powerline interface is connected to switch port 5 (Label LAN4). Installation: No "fresh" device was available for testing the factory image. It is not known whether flashing via OEM firmware GUI is possible or not. A discussion from 2018 [1] about that indicates a few adjustments are necessary, but it is not clear whether those are already implemented with the TPLINK_HEADER_VERSION = 2 or not. Note that for the TL-WPA8630P v1, the TPLINK_HWID needs to be changed to 0x86310001 to allow factory flashing. [1] https://forum.openwrt.org/t/solved-tl-wpa8630p-lede-does-not-install/8161/27 Recovery: Recovery is only possible via serial. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
123 lines
1.9 KiB
Plaintext
123 lines
1.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
keys: keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
leds {
|
|
label = "LED control button";
|
|
linux,code = <BTN_0>;
|
|
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
pair {
|
|
label = "Pair button";
|
|
linux,code = <BTN_1>;
|
|
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "tp-link:green:power";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan {
|
|
label = "tp-link:green:lan";
|
|
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi2g {
|
|
label = "tp-link:green:wifi2g";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
wifi5g {
|
|
label = "tp-link:green:wifi5g";
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions: partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "sgmii";
|
|
qca,mib-poll-interval = <500>;
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "sgmii";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|