adfc8d8eca
This commit adds firmware partition compatible for the AVM FRITZ!Box 4020 and AVM FRITZ!WLAN Repeater 300E. This allows to select the correct mtdsplit parser instead of trying all available ones one by one. Signed-off-by: David Bauer <mail@david-bauer.net>
181 lines
3.0 KiB
Plaintext
181 lines
3.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
/ {
|
|
compatible = "avm,fritz4020", "qca,qca9560";
|
|
model = "AVM FRITZ!Box 4020";
|
|
|
|
aliases {
|
|
led-boot = &power;
|
|
led-failsafe = &info_red;
|
|
led-running = &power;
|
|
led-upgrade = &info_red;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
led_spi {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
gpio-sck = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
gpio-mosi = <&gpio 19 GPIO_ACTIVE_HIGH>;
|
|
num-chipselects = <0>;
|
|
|
|
led_gpio: led_gpio@0 {
|
|
compatible = "fairchild,74hc595";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
registers-number = <1>;
|
|
lines-initial-states = /bits/ 8 <0xff>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
gpio_latch_bit {
|
|
gpio-hog;
|
|
gpios = <7 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "gpio-latch-bit";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power: power {
|
|
label = "fritz4020:green:power";
|
|
gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan {
|
|
label = "fritz4020:green:wlan";
|
|
gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
default-state = "off";
|
|
};
|
|
|
|
lan {
|
|
label = "fritz4020:green:lan";
|
|
gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
wan {
|
|
label = "fritz4020:green:wan";
|
|
gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
info {
|
|
label = "fritz4020:green:info";
|
|
gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
info_red: info_red {
|
|
label = "fritz4020:red:info";
|
|
gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
wps_button {
|
|
label = "WPS button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan_button {
|
|
label = "WLAN button";
|
|
linux,code = <KEY_RFKILL>;
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "urlader";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1 {
|
|
compatible = "avm,eva-firmware";
|
|
label = "firmware";
|
|
reg = <0x020000 0xee0000>;
|
|
};
|
|
|
|
partition@2 {
|
|
label = "tffs (1)";
|
|
reg = <0xf00000 0x080000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@3 {
|
|
label = "tffs (2)";
|
|
reg = <0xf80000 0x080000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-mode = "mii";
|
|
phy-handle = <&swphy0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <1>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
qca,no-eeprom;
|
|
};
|