131671bc54
ALFA Network Tube-2HQ is a successor of the Tube-2H/P series (EOL) which was based on the Atheros AR9331. The new version uses Qualcomm QCA9531. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 64 or 128 MB of RAM (DDR2) - 16+ MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet with passive PoE input (24 V) (802.3at/af PoE support with optional module) - 1T1R 2.4 GHz Wi-Fi with external PA (SE2623L, up to 27 dBm) and LNA - 1x Type-N (male) antenna connector - 6x LED (5x driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - UART (4-pin, 2.00 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
66 lines
1.1 KiB
Plaintext
66 lines
1.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca9531_alfa-network_r36a.dtsi"
|
|
|
|
/ {
|
|
model = "ALFA Network Tube-2HQ";
|
|
compatible = "alfa-network,tube-2hq", "qca,qca9531";
|
|
|
|
aliases {
|
|
led-boot = &led_signal4;
|
|
led-failsafe = &led_signal4;
|
|
led-upgrade = &led_signal4;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&enable_gpio4 &enable_gpio16>;
|
|
|
|
lan {
|
|
label = "blue:lan";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_signal4: signal4 {
|
|
label = "green:signal4";
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
signal1 {
|
|
label = "red:signal1";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
signal2 {
|
|
label = "orange:signal2";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
signal3 {
|
|
label = "green:signal3";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
nvmem-cells = <&macaddr_art_1002>;
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
mac-address-increment = <(-1)>;
|
|
};
|
|
|
|
ð1 {
|
|
compatible = "syscon", "simple-mfd";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "disabled";
|
|
};
|