416d4483e8
Asus RP-AC51 Repeater Category: AC750 300+433 (OEM w. unstable driver) AC1200 300+866 (OpenWrt w. stable driver) Hardware specifications: Board: AP147 SoC: QCA9531 2.4G b/g/n WiFi: QCA9886 5G n/ac DRAM: 128MB DDR2 Flash: gd25q128 16MB SPI-NOR LAN/WAN: AR8229 1x100M Clocks: CPU:650MHz, DDR:600MHz, AHB:200MHz MAC addresses as verified by OEM firmware: use address source Lan/W2G *:C8 art 0x1002 (label) 5G *:CC art 0x5006 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 Start the Asus firmware restoration utility, specify the factory image and press upload Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: set computer to a static ip, 192.168.1.10 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
141 lines
2.2 KiB
Plaintext
141 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca953x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "ASUS RP-AC51";
|
|
compatible = "asus,rp-ac51", "qca,qca9531";
|
|
|
|
aliases {
|
|
led-boot = &led_wps;
|
|
led-failsafe = &led_wps;
|
|
led-running = &led_wps;
|
|
led-upgrade = &led_wps;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps {
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
reset {
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "blue:power";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_wps: wps {
|
|
label = "red:wps";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
lan {
|
|
label = "blue:lan";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wlan2g {
|
|
label = "blue:wlan2g";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wlan5g {
|
|
label = "blue:wlan5g";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@50000 {
|
|
label = "art";
|
|
reg = <0x050000 0x10000>;
|
|
read-only;
|
|
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_art_0: macaddr@0 {
|
|
reg = <0x0 0x6>;
|
|
};
|
|
|
|
macaddr_art_1002: macaddr@1002 {
|
|
reg = <0x1002 0x6>;
|
|
};
|
|
};
|
|
|
|
partition@60000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x060000 0xfa0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy4>;
|
|
|
|
nvmem-cells = <&macaddr_art_0>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
ð1 {
|
|
nvmem-cells = <&macaddr_art_1002>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
qca,no-eeprom;
|
|
};
|