6ffe8a473e
The Seagate BlackArmor NAS220 is a consumer NAS
with two internal drive bays. The stock OS runs
RAID 1 over the disks via mdadm.
Device specification:
- SoC: Marvell 88F6192 800 MHz
- RAM: 128 MB
- Flash: 32 MB
- 2 x internal SATA II drives
- Ethernet: 10/100/1000 Mbps (single port, no switch)
- WLAN: None
- LED: Power, Status, Sata Activity
- Key: Power, Reset
- Serial: 10 pin header, (115200,8,N,1), 3.3V TTL
9|x - x|10
7|x - x|8
5|x - GND|6
3|x - RX|4
1|TX - x|2
front of case
- USB ports: 2 x USB 2.0
Flash instruction:
NOTE: this process uses a serial connection. It will upgrade the
bootloader and reset the bootloader environment variables
TFTP server setup
- Setup PC with TFTP server set the PC IP to 10.4.50.5 as TFTP server
- Copy these files to TFTP server location
- u-boot.kwb
- seagate_blackarmor-nas220-initramfs-uImage
- seagate_blackarmor-nas220-squashfs-sysupgrade.bin
- seagate_blackarmor-nas220-squashfs-factory.bin
Seagate NAS setup
- Connect LAN cable between PC and seagate device
- Connect to serial to seagate device
Install u-boot
- Boot seagate device and stop in bootloader by pressing any key
- run 'printenv' from u-boot and save the values
- tftpboot 0x2000000 u-boot.kwb
- nand erase.part uboot
- nand write 0x2000000 0x0 ${filesize}
- reset
Update MAC address in u-boot env
- Stop in u-boot by pressing any key
- Get your MAC address from your saved printenv. Is also on chassis
- setenv ethaddr <your MAC>
- saveenv
Option 1 (recommended) - Install OpenWrt via initramfs and sysupgrade
- tftpboot 0x2000000 seagate_blackarmor-nas220-initramfs-uImage
- bootm 0x2000000
- *OpenWrt should be running now, however it is not written to flash yet*
- From the running instance of OpenWrt use Luci's "flash image" feature
from the web site or use sysupgrade from the console to write
seagate_blackarmor-nas220-squashfs-sysupgrade.bin to flash
Option 2 - Install OpenWrt by flashing factory image from u-boot
- nand erase.part ubi
- tftpboot 0x2000000 seagate_blackarmor-nas220-squashfs-factory.bin
- nand write 0x2000000 ubi ${filesize}
- reset
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
100 lines
2.0 KiB
Diff
100 lines
2.0 KiB
Diff
--- a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
|
|
+++ b/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
|
|
@@ -17,6 +17,13 @@
|
|
compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192",
|
|
"marvell,kirkwood";
|
|
|
|
+ aliases {
|
|
+ led-boot = &led_status_amber;
|
|
+ led-failsafe = &led_status_amber;
|
|
+ led-running = &led_status_blue;
|
|
+ led-upgrade = &led_status_amber;
|
|
+ };
|
|
+
|
|
memory { /* 128 MB */
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x8000000>;
|
|
@@ -36,14 +43,14 @@
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
- label = "Reset";
|
|
- linux,code = <KEY_POWER>;
|
|
+ label = "Reset Button";
|
|
+ linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
- button {
|
|
- label = "Power";
|
|
- linux,code = <KEY_SLEEP>;
|
|
+ power {
|
|
+ label = "Power Button";
|
|
+ linux,code = <KEY_POWER>;
|
|
gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
@@ -51,11 +58,27 @@
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
- blue-power {
|
|
+ led_power_blue: power_blue {
|
|
label = "nas220:blue:power";
|
|
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "default-on";
|
|
};
|
|
+
|
|
+ disk_blue {
|
|
+ label = "nas220:blue:disk";
|
|
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
|
|
+ linux,default-trigger = "disk-activity";
|
|
+ };
|
|
+
|
|
+ led_status_blue: status_blue {
|
|
+ label = "nas220:blue:status";
|
|
+ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
|
|
+ };
|
|
+
|
|
+ led_status_amber: status_amber {
|
|
+ label = "nas220:amber:status";
|
|
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
|
|
+ };
|
|
};
|
|
|
|
regulators {
|
|
@@ -153,6 +176,33 @@
|
|
|
|
&nand {
|
|
status = "okay";
|
|
+
|
|
+ partitions {
|
|
+ compatible = "fixed-partitions";
|
|
+
|
|
+ partition@0 {
|
|
+ label = "uboot";
|
|
+ reg = <0x0 0xa0000>;
|
|
+ read-only;
|
|
+ };
|
|
+
|
|
+ partition@a0000 {
|
|
+ label = "uboot-env";
|
|
+ reg = <0xa0000 0x10000>;
|
|
+ read-only;
|
|
+ };
|
|
+
|
|
+ partition@b0000 {
|
|
+ label = "reserved";
|
|
+ reg = <0xb0000 0x10000>;
|
|
+ read-only;
|
|
+ };
|
|
+
|
|
+ partition@c0000 {
|
|
+ label = "ubi";
|
|
+ reg = <0xc0000 0x1e80000>;
|
|
+ };
|
|
+ };
|
|
};
|
|
|
|
&mdio {
|