tn3399_openwrt/target/linux/ramips/dts/mt7628an_ravpower_rp-wd009.dts
David Bauer e959048c12 ramips: add support for RAVPower RP-WD009
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.

Hardware
--------
CPU:   MediaTek MT7628AN
RAM:   64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN:  MediaTek MT7628AN 2T2R b/g/n
       MediaTek MT7610E  1T1R n/ac
ETH:   1x FastEthernet
SD:    SD Card slot
USB:   USB 2.0

Custom PMIC on the I2C bus (address 0x0a).

Installation
------------

1. Press and hold down the reset button.

2. Power up the Device. Keep pressing the reset button for 10
   more seconds until the Globe LED lights up.

3. Attach your Computer to the Ethernet port. Assign yourself the
   address 10.10.10.1/24.

4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
   factory image.

5. The flashing will take around 1 minute. The device will reboot
   automatically into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:01 +02:00

203 lines
3.1 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7628an.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "ravpower,rp-wd009", "mediatek,mt7628an-soc";
model = "RAVPower RP-WD009";
aliases {
led-boot = &led_globe;
led-failsafe = &led_globe;
led-running = &led_globe;
led-upgrade = &led_globe;
};
chosen {
bootargs = "console=ttyS0,57600";
};
leds {
compatible = "gpio-leds";
led_globe: globe {
label = "rp-wd009:white:globe";
gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
};
wlan2 {
label = "rp-wd009:white:wlan2";
gpios = <&gpio 44 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tpt";
};
wlan5 {
label = "rp-wd009:white:wlan5";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
sd_white {
label = "rp-wd009:white:sd";
gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
};
sd_red {
label = "rp-wd009:red:sd";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
/* Power interrupt on Pin 39 */
rfkill {
label = "rfkill";
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
backup {
label = "backup";
gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
linux,code = <KEY_COPY>;
};
};
};
&gpio {
mt7610-power {
gpio-hog;
gpios = <20 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "mt7610-power";
};
};
&state_default {
gpio {
groups = "uart1", "wled_an", "p0led_an", "p2led_an", "p3led_an",
"p4led_an", "uart2", "pwm0", "i2s";
function = "gpio";
};
};
&ehci {
status = "okay";
};
&ohci {
status = "okay";
};
&sdhci {
status = "okay";
};
&i2c {
status = "okay";
/* Custom PMIC at 0x0a */
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "bootloader";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "loader";
reg = <0x50000 0x180000>;
};
partition@1d0000 {
label = "params";
reg = <0x1d0000 0x10000>;
read-only;
};
partition@1e0000 {
label = "user_backup";
reg = <0x1e0000 0x10000>;
read-only;
};
partition@1f0000 {
label = "user";
reg = <0x1f0000 0x10000>;
read-only;
};
partition@200000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x200000 0xdf0000>;
};
partition@ff0000 {
label = "mode";
reg = <0xff0000 0x10000>;
read-only;
};
};
};
};
&wmac {
status = "okay";
};
&ethernet {
mtd-mac-address = <&factory 0x4>;
};