ipq807x: add support for Yuncore AX880
SPECIFICATION:
- Chipset: IPQ8072A +QCN5054+QCN5024+QCA8081*2
- Flash NOR-8MB AND NAND-128MB
- RAM 1Gb DDR
- IEEE 802.11: 802.11ax/ac/b/g/n
- 4*4 2.4G Wi-Fi standard 802.11b/g/n/ax
- 4*4 5.8G Wi-Fi Standard 802.11 a/n/ac/ax
- 2x 1 Gbps Ethernet (QCA8081) with 802.3at PoE input support
- 1x Reset
- 1x Bluetooth(optional)
- 1x DC Port 12V 3A
- 4x Antenna IPEX Connector, 3dBi omni antennas
- Data Rate: 3657Mbps ( 2.4G: 1182Mbps (11ax 4x4); 5.8G: 2475Mbps (11ax 4x4))
- RF Power: 2.4g ≤ 20dBm; 5.8g ≤ 19dBm
- LED light: Sys; 5.8G wifi; 2.4G wifi; WAN; LAN
- Max Power Consumption: ≤ 22W
- Size: 198mm * 198mm * 41.02mm
BACKUP YOUR STOCK FIRMWARE:
```
export device=ax880
mkdir -p /tmp/fw_dump_$device
cd /tmp/fw_dump_$device
dmesg > dmesg_$device.log
dtc -I fs /sys/firmware/devicetree/base > $device.dts
cat /proc/device-tree/model > model
cat /proc/mtd > proc_mtd
while read p; do
mtd_dev=$(echo $p | cut -d: -f1)
echo $mtd_dev
dd if=/dev/$mtd_dev of=$mtd_dev
done < proc_mtd
md5sum * > md5sum.log
tar -cvzf ../$device.tar.gz .
export sum=$(md5sum /tmp/$device.tar.gz | cut -d' ' -f1)
mv ../$device.tar.gz /tmp/${device}_${sum}.tar.gz
echo fw backup saved to: /tmp/${device}_${sum}.tar.gz
```
Upload your backup via tftp to the safe place.
INSTALLATION:
1. stock firmware web ui
Rename factory.bin fw image file to factory.ubin. Flash this image
like ordinary stock fw upgrade.
2. stock firmware telnet method
Enter telnet cli (login: root, password: 476t*_f0%g09y) and upload
factory.bin fw image and rename it to factory.ubin
`cd /tmp && wget <your_web_server_ip>/factory.ubin`
`sysupgrade factory.ubin
3. initramfs method
Put openwrt-ipq807x-generic-yuncore_ax880-initramfs-uImage.itb to your
TFTP server and rename it to ax880.initram
Enable serial console and enter to the u-boot cli.
Exec these commands:
`tftpboot <your_tftp_server_ip>:ax880.initram`
`dhcp`
When downloading is finished:
`bootm`
After booting the device, you need to upload to the device factory.ubi fw image.
```
cd /tmp && wget <your_web_server_ip>/factory.ubi`
export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1)
export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f factory.ubi
ubiformat /dev/${rootfs_1} -y -f factory.ubi
reboot
```
4. u-boot factory.ubi image method
Put openwrt-ipq807x-generic-yuncore_ax880-squashfs-factory.ubi to your
TFTP server and rename it to ax880.ubi
Enter u-boot cli and exec these commands:
`tftpboot <your_tftp_server_ip>:ax880.ubi`
`dhcp`
After downloading is finished:
`flash rootfs`
`flash rootfs_1`
`reset`
5. u-boot factory.bin method
Put openwrt-ipq807x-generic-yuncore_ax880-squashfs-factory.bin to your
TFTP server and rename it to ax880.bin
Enter u-boot cli and exec these commands:
`tftpboot <your_tftp_server_ip>:ax880.bin`
`dhcp`
After downloading is finished:
`imgaddr=$fileaddr && nand device 0`
Erase rootfs memory:
`nand erase 0x00000000 0x03400000`
Write rootfs:
`nand write $fileaddr 0x00000000 $filesize`
Erase rootfs_1 memory:
`nand erase 0x3c00000 0x3400000`
Write rootfs_1
`nand write $fileaddr 0x3c00000 $filesize`
`reset`
STOCK FIRMWARE RECOVERY:
Boot initramfs image.
Upload your rootfs mtd partition to the device using scp or download
it from the device using wget.
Enter device ssh cli and exec:
```
cd /tmp && wget <your_web_server_ip>/mtd21`
export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1)
export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f /tmp/mtd21
ubiformat /dev/${rootfs_1} -y -f /tmp/mtd21
reboot
```
Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
Isaev Ruslan
Christian Marangi
parent
05e516b12d
commit
3763a6a075
|
|
@ -6,9 +6,9 @@ PKG_RELEASE:=1
|
|||
|
||||
PKG_SOURCE_PROTO:=git
|
||||
PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git
|
||||
PKG_SOURCE_DATE:=2023-10-12
|
||||
PKG_SOURCE_VERSION:=cd04ab7f984fe28613276c01fd0ac7afbe5516d5
|
||||
PKG_MIRROR_HASH:=857ae436fd09785749411a665b31c82cec84b68b1e096f69ebb6c2a0efb5583f
|
||||
PKG_SOURCE_DATE:=2023-11-02
|
||||
PKG_SOURCE_VERSION:=371d4dce9b9a4b4dfd59bc902bb216f7133743cb
|
||||
PKG_MIRROR_HASH:=9c309f81cb1e464580ccdacc3f7a660df8a5a07a8b87f71e9d00f630ac0412ad
|
||||
|
||||
PKG_FLAGS:=nonshared
|
||||
|
||||
|
|
@ -44,6 +44,7 @@ ALLWIFIBOARDS:= \
|
|||
xiaomi_ax3600 \
|
||||
xiaomi_ax9000 \
|
||||
yyets_le1 \
|
||||
yuncore_ax880 \
|
||||
zte_mf289f \
|
||||
zte_mf287 \
|
||||
zte_mf287plus \
|
||||
|
|
@ -151,6 +152,7 @@ $(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
|
|||
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
|
||||
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
|
||||
$(eval $(call generate-ipq-wifi-package,yyets_le1,YYeTs LE1))
|
||||
$(eval $(call generate-ipq-wifi-package,yuncore_ax880,Yuncore AX880))
|
||||
$(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))
|
||||
$(eval $(call generate-ipq-wifi-package,zte_mf287,ZTE MF287))
|
||||
$(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus))
|
||||
|
|
|
|||
|
|
@ -0,0 +1,370 @@
|
|||
// SPDX-License-Identifier: MIT, GPL-2.0 or later
|
||||
/* Copyright (c) 2023, Ruslan Isaev <legale.legale@gmail.com> */
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq8074.dtsi"
|
||||
#include "ipq8074-hk-cpu.dtsi"
|
||||
#include "ipq8074-ess.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Yuncore AX880";
|
||||
compatible = "yuncore,ax880", "qcom,ipq8074", "qcom,ipq8074-hk09";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart5;
|
||||
serial1 = &blsp1_uart3;
|
||||
led-boot = &led_system;
|
||||
led-failsafe = &led_system;
|
||||
led-running = &led_system;
|
||||
led-upgrade = &led_system;
|
||||
/* Aliases as required by u-boot to patch MAC addresses */
|
||||
ethernet0 = &dp5_syn;
|
||||
ethernet1 = &dp6_syn;
|
||||
label-mac-device = &dp5_syn;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system: system {
|
||||
label = "system";
|
||||
color = "red";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "wlan2g";
|
||||
color = "green";
|
||||
linux,default-trigger = "phy0tpt";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "wlan5g";
|
||||
color = "blue";
|
||||
linux,default-trigger = "phy1tpt";
|
||||
gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pins {
|
||||
mdc {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button_pins {
|
||||
reset_button {
|
||||
pins = "gpio57";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:sbl1";
|
||||
reg = <0x0 0x50000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "0:mibib";
|
||||
reg = <0x50000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:bootconfig";
|
||||
reg = <0x60000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "0:bootconfig1";
|
||||
reg = <0x80000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@a0000 {
|
||||
label = "0:qsee_1";
|
||||
reg = <0xa0000 0x180000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@220000 {
|
||||
label = "0:qsee";
|
||||
reg = <0x220000 0x180000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3a0000 {
|
||||
label = "0:devcfg";
|
||||
reg = <0x3a0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3b0000 {
|
||||
label = "0:devcfg_1";
|
||||
reg = <0x3b0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3c0000 {
|
||||
label = "0:apdp";
|
||||
reg = <0x3c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3d0000 {
|
||||
label = "0:apdp_1";
|
||||
reg = <0x3d0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3e0000 {
|
||||
label = "0:rpm_1";
|
||||
reg = <0x3e0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@420000 {
|
||||
label = "0:rpm";
|
||||
reg = <0x420000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@460000 {
|
||||
label = "0:cdt_1";
|
||||
reg = <0x460000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@470000 {
|
||||
label = "0:cdt";
|
||||
reg = <0x470000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@480000 {
|
||||
label = "0:appsblenv";
|
||||
reg = <0x480000 0x10000>;
|
||||
};
|
||||
|
||||
partition@490000 {
|
||||
label = "0:appsbl_1";
|
||||
reg = <0x490000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@550000 {
|
||||
label = "0:appsbl";
|
||||
reg = <0x530000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@610000 {
|
||||
label = "0:art";
|
||||
reg = <0x5d0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@650000 {
|
||||
label = "0:ethphyfw";
|
||||
reg = <0x610000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
//serial interface
|
||||
&blsp1_uart3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qusb_phy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "rootfs_1";
|
||||
reg = <0x0000000 0x3400000>;
|
||||
};
|
||||
|
||||
partition@3400000 {
|
||||
label = "0:wififw";
|
||||
reg = <0x3400000 0x800000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
rootfs: partition@3c00000 {
|
||||
label = "rootfs";
|
||||
reg = <0x3c00000 0x3400000>;
|
||||
};
|
||||
|
||||
partition@7000000 {
|
||||
label = "0:wififw_1";
|
||||
reg = <0x7000000 0x800000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
qca8081_24: ethernet-phy@24 {
|
||||
compatible = "ethernet-phy-id004d.d101";
|
||||
reg = <24>;
|
||||
reset-gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
qca8081_28: ethernet-phy@28 {
|
||||
compatible = "ethernet-phy-id004d.d101";
|
||||
reg = <28>;
|
||||
reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x3e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x40>; /* wan port bitmap */
|
||||
switch_mac_mode = <0xff>; /* mac mode for uniphy instance0*/
|
||||
switch_mac_mode1 = <0xf>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode2 = <0xf>; /* mac mode for uniphy instance2*/
|
||||
bm_tick_mode = <0>; /* bm tick mode */
|
||||
tm_tick_mode = <0>; /* tm tick mode */
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@4 {
|
||||
port_id = <5>;
|
||||
phy_address = <24>;
|
||||
port_mac_sel = "QGMAC_PORT";
|
||||
};
|
||||
port@5 {
|
||||
port_id = <6>;
|
||||
phy_address = <28>;
|
||||
port_mac_sel = "QGMAC_PORT";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dp5_syn {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8081_24>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
&dp6_syn {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8081_28>;
|
||||
label = "lan";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
qcom,ath11k-calibration-variant = "Yuncore-AX880";
|
||||
};
|
||||
|
|
@ -253,3 +253,19 @@ define Device/zyxel_nbg7815
|
|||
kmod-bluetooth
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_nbg7815
|
||||
|
||||
define Device/yuncore_ax880
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Yuncore
|
||||
DEVICE_MODEL := AX880
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_DTS_CONFIG := config@hk09
|
||||
SOC := ipq8072
|
||||
DEVICE_PACKAGES := ipq-wifi-yuncore_ax880
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
|
||||
endef
|
||||
TARGET_DEVICES += yuncore_ax880
|
||||
|
||||
|
|
|
|||
|
|
@ -16,7 +16,8 @@ ipq807x_setup_interfaces()
|
|||
xiaomi,ax9000)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
||||
;;
|
||||
edgecore,eap102)
|
||||
edgecore,eap102|\
|
||||
yuncore,ax880)
|
||||
ucidef_set_interfaces_lan_wan "lan" "wan"
|
||||
;;
|
||||
edimax,cax1800)
|
||||
|
|
|
|||
|
|
@ -22,6 +22,7 @@ case "$FIRMWARE" in
|
|||
redmi,ax6|\
|
||||
xiaomi,ax3600|\
|
||||
xiaomi,ax9000|\
|
||||
yuncore,ax880|\
|
||||
zyxel,nbg7815)
|
||||
caldata_extract "0:art" 0x1000 0x20000
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -4,7 +4,8 @@ START=99
|
|||
|
||||
boot() {
|
||||
case $(board_name) in
|
||||
edgecore,eap102)
|
||||
edgecore,eap102|\
|
||||
yuncore,ax880)
|
||||
fw_setenv upgrade_available 0
|
||||
# Unset changed flag after sysupgrade complete
|
||||
fw_setenv changed
|
||||
|
|
|
|||
|
|
@ -113,6 +113,18 @@ platform_do_upgrade() {
|
|||
CI_ROOT_UBIPART="rootfs"
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
yuncore,ax880)
|
||||
active="$(fw_printenv -n active)"
|
||||
if [ "$active" -eq "1" ]; then
|
||||
CI_UBIPART="rootfs_1"
|
||||
else
|
||||
CI_UBIPART="rootfs"
|
||||
fi
|
||||
# force altbootcmd which handles partition change in u-boot
|
||||
fw_setenv bootcount 3
|
||||
fw_setenv upgrade_available 1
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
*)
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user