ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender, based on MediaTek MT7621A and MT7615E. According to the wikidevi entry for RE650 this device is identical with TP-Link RE500 as hardware. This patch supports only RE650. Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 16 MB - Winbond 25Q128FVSG - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART header (J1) - 2:GND, 3:RX, 4:TX Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: Unfortunately, I can't find an easy way to recover the RE without opening the device and using modified binaries. The TFTP upload will only work if selected from u-boot, which means you have to open the device and attach to the serial console. The TFTP update procedure does *not* accept the published vendor firmware binaries. However, it allows to flash kernel + rootfs binaries, and this works if you have a backup of the original contents of the flash. It's probably possible to create special image out of the vendor binaries and use that as recovery image. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com> [re-added variables for kernel header] Signed-off-by: David Bauer <mail@david-bauer.net>
This commit is contained in:
Georgi Vlaev
David Bauer
parent
d6198d8625
commit
8c51ddeff0
|
|
@ -347,7 +347,8 @@ tplink,archer-mr200)
|
|||
ucidef_set_led_netdev "wan" "wan" "$boardname:white:wan" "usb0"
|
||||
set_wifi_led "$boardname:white:wlan"
|
||||
;;
|
||||
tplink,re350-v1)
|
||||
tplink,re350-v1|\
|
||||
tplink,re650-v1)
|
||||
ucidef_set_led_netdev "wifi2g" "Wifi 2.4G" "$boardname:blue:wifi2G" "wlan0"
|
||||
ucidef_set_led_netdev "wifi5g" "Wifi 5G" "$boardname:blue:wifi5G" "wlan1"
|
||||
ucidef_set_led_netdev "eth_act" "LAN act" "$boardname:green:eth_act" "eth0" "tx rx"
|
||||
|
|
|
|||
|
|
@ -285,7 +285,8 @@ ramips_setup_interfaces()
|
|||
dlink,dir-510l|\
|
||||
glinet,vixmini|\
|
||||
netgear,ex6150|\
|
||||
tplink,re350-v1)
|
||||
tplink,re350-v1|\
|
||||
tplink,re650-v1)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "6@eth0"
|
||||
;;
|
||||
|
|
|
|||
177
target/linux/ramips/dts/mt7621_tplink_re650-v1.dts
Normal file
177
target/linux/ramips/dts/mt7621_tplink_re650-v1.dts
Normal file
|
|
@ -0,0 +1,177 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "tplink,re650-v1", "mediatek,mt7621-soc";
|
||||
model = "TP-Link RE650 v1";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,57600";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "re650-v1:blue:power";
|
||||
gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi2g {
|
||||
label = "re650-v1:blue:wifi2G";
|
||||
gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi5g {
|
||||
label = "re650-v1:blue:wifi5G";
|
||||
gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps_red {
|
||||
label = "re650-v1:red:wps";
|
||||
gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wps_blue {
|
||||
label = "re650-v1:blue:wps";
|
||||
gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
eth_act {
|
||||
label = "re650-v1:green:eth_act";
|
||||
gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
eth_link {
|
||||
label = "re650-v1:green:eth_link";
|
||||
gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
power {
|
||||
label = "power";
|
||||
gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
linux,code = <KEY_POWER>;
|
||||
};
|
||||
|
||||
led {
|
||||
label = "led";
|
||||
gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
linux,code = <KEY_LIGHTS_TOGGLE>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
w25q64@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <40000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "tplink,firmware";
|
||||
label = "firmware";
|
||||
reg = <0x20000 0xde0000>;
|
||||
};
|
||||
|
||||
config: partition@e00000 {
|
||||
label = "config";
|
||||
reg = <0xe00000 0x50000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* range 0xe50000 to 0xff0000 is empty in vendor
|
||||
* firmware, so we do not use it either
|
||||
*/
|
||||
|
||||
radio: partition@ff0000 {
|
||||
label = "radio";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&radio 0>;
|
||||
mtd-mac-address = <&config 0x10008>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
ieee80211-freq-limit = <2400000 2500000>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&radio 0x8000>;
|
||||
mtd-mac-address = <&config 0x10008>;
|
||||
mtd-mac-address-increment = <2>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
mtd-mac-address = <&config 0x10008>;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "rgmii2", "wdt";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -531,25 +531,41 @@ define Device/totolink_a7000r
|
|||
endef
|
||||
TARGET_DEVICES += totolink_a7000r
|
||||
|
||||
define Device/tplink_re350-v1
|
||||
define Device/tplink-safeloader
|
||||
MTK_SOC := mt7621
|
||||
DEVICE_VENDOR := TP-Link
|
||||
TPLINK_BOARD_ID :=
|
||||
TPLINK_HWID := 0x0
|
||||
TPLINK_HWREV := 0
|
||||
TPLINK_HEADER_VERSION := 1
|
||||
KERNEL := $(KERNEL_DTB) | tplink-v1-header -e -O
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \
|
||||
append-metadata | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
|
||||
endef
|
||||
|
||||
define Device/tplink_re350-v1
|
||||
$(Device/tplink-safeloader)
|
||||
DEVICE_MODEL := RE350
|
||||
DEVICE_VARIANT := v1
|
||||
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 wpad-basic
|
||||
TPLINK_BOARD_ID := RE350-V1
|
||||
TPLINK_HWID := 0x0
|
||||
TPLINK_HWREV := 0
|
||||
TPLINK_HEADER_VERSION := 1
|
||||
IMAGE_SIZE := 6016k
|
||||
KERNEL := $(KERNEL_DTB) | tplink-v1-header -e -O
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | append-metadata | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
|
||||
SUPPORTED_DEVICES += re350-v1
|
||||
endef
|
||||
TARGET_DEVICES += tplink_re350-v1
|
||||
|
||||
define Device/tplink_re650-v1
|
||||
$(Device/tplink-safeloader)
|
||||
DEVICE_MODEL := RE650
|
||||
DEVICE_VARIANT := v1
|
||||
DEVICE_PACKAGES := kmod-mt7615e wpad-basic
|
||||
TPLINK_BOARD_ID := RE650-V1
|
||||
IMAGE_SIZE := 14208k
|
||||
endef
|
||||
TARGET_DEVICES += tplink_re650-v1
|
||||
|
||||
define Device/ubiquiti_edgerouterx
|
||||
MTK_SOC := mt7621
|
||||
FILESYSTEMS := squashfs
|
||||
|
|
|
|||
|
|
@ -1366,6 +1366,43 @@ static struct device_info boards[] = {
|
|||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the RE650 */
|
||||
{
|
||||
.id = "RE650-V1",
|
||||
.vendor = "",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"{product_name:RE650,product_ver:1.0.0,special_id:00000000}\r\n"
|
||||
"{product_name:RE650,product_ver:1.0.0,special_id:55530000}\r\n"
|
||||
"{product_name:RE650,product_ver:1.0.0,special_id:45550000}\r\n"
|
||||
"{product_name:RE650,product_ver:1.0.0,special_id:4A500000}\r\n"
|
||||
"{product_name:RE650,product_ver:1.0.0,special_id:43410000}\r\n"
|
||||
"{product_name:RE650,product_ver:1.0.0,special_id:41550000}\r\n"
|
||||
"{product_name:RE650,product_ver:1.0.0,special_id:41530000}\r\n",
|
||||
.support_trail = '\x00',
|
||||
.soft_ver = NULL,
|
||||
|
||||
/* We're using a dynamic kernel/rootfs split here */
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"firmware", 0x20000, 0xde0000},
|
||||
{"partition-table", 0xe00000, 0x02000},
|
||||
{"default-mac", 0xe10000, 0x00020},
|
||||
{"pin", 0xe10100, 0x00020},
|
||||
{"product-info", 0xe11100, 0x01000},
|
||||
{"soft-version", 0xe20000, 0x01000},
|
||||
{"support-list", 0xe21000, 0x01000},
|
||||
{"profile", 0xe22000, 0x08000},
|
||||
{"user-config", 0xe30000, 0x10000},
|
||||
{"default-config", 0xe40000, 0x10000},
|
||||
{"radio", 0xff0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
{}
|
||||
};
|
||||
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user