ipq807x: add Edimax CAX1800
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.
Specifications:
• CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
• RAM: 512MB of DDR3
• Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
This commit is contained in:
Dirk Buchwalder
Robert Marko
parent
8253cb2de5
commit
a36fc589fe
|
|
@ -8,6 +8,11 @@ touch /etc/config/ubootenv
|
|||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
edimax,cax1800)
|
||||
idx="$(find_mtd_index 0:appsblenv)"
|
||||
[ -n "$idx" ] && \
|
||||
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x20000"
|
||||
;;
|
||||
redmi,ax6|\
|
||||
xiaomi,ax3600)
|
||||
idx="$(find_mtd_index 0:appsblenv)"
|
||||
|
|
|
|||
|
|
@ -29,6 +29,7 @@ ALLWIFIBOARDS:= \
|
|||
devolo_magic-2-wifi-next \
|
||||
edgecore_ecw5410 \
|
||||
edgecore_oap100 \
|
||||
edimax_cax1800 \
|
||||
extreme-networks_ws-ap3915i \
|
||||
glinet_gl-a1300 \
|
||||
glinet_gl-ap1300 \
|
||||
|
|
@ -120,6 +121,7 @@ $(eval $(call generate-ipq-wifi-package,aruba_ap-365,Aruba AP-365))
|
|||
$(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2 WiFi next))
|
||||
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
|
||||
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
|
||||
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
||||
$(eval $(call generate-ipq-wifi-package,extreme-networks_ws-ap3915i,Edgecore OAP100))
|
||||
$(eval $(call generate-ipq-wifi-package,glinet_gl-a1300,GL.iNet GL-A1300))
|
||||
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
|
||||
|
|
|
|||
BIN
package/firmware/ipq-wifi/board-edimax_cax1800.ipq8074
Normal file
BIN
package/firmware/ipq-wifi/board-edimax_cax1800.ipq8074
Normal file
Binary file not shown.
|
|
@ -11,6 +11,9 @@ ipq807x_setup_interfaces()
|
|||
local board="$1"
|
||||
|
||||
case "$board" in
|
||||
edimax,cax1800)
|
||||
ucidef_set_interfaces_lan_wan "lan"
|
||||
;;
|
||||
redmi,ax6|\
|
||||
xiaomi,ax3600)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
||||
|
|
|
|||
|
|
@ -9,6 +9,7 @@ board=$(board_name)
|
|||
case "$FIRMWARE" in
|
||||
"ath11k/IPQ8074/hw2.0/cal-ahb-c000000.wifi.bin")
|
||||
case "$board" in
|
||||
edimax,cax1800|\
|
||||
redmi,ax6|\
|
||||
xiaomi,ax3600)
|
||||
caldata_extract "0:art" 0x1000 0x20000
|
||||
|
|
|
|||
|
|
@ -42,6 +42,9 @@ platform_pre_upgrade() {
|
|||
|
||||
platform_do_upgrade() {
|
||||
case "$(board_name)" in
|
||||
edimax,cax1800)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
redmi,ax6|\
|
||||
xiaomi,ax3600)
|
||||
# Make sure that UART is enabled
|
||||
|
|
|
|||
|
|
@ -0,0 +1,322 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2021, Dirk Buchwalder <buchwalder@posteo.de> */
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq8074-512m.dtsi"
|
||||
#include "ipq8074-ac-cpu.dtsi"
|
||||
#include "ipq8074-ess.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Edimax CAX1800";
|
||||
compatible = "edimax,cax1800", "qcom,ipq8074";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart5;
|
||||
led-boot = &led_system_red;
|
||||
led-failsafe = &led_system_red;
|
||||
led-running = &led_system_green;
|
||||
led-upgrade = &led_system_red;
|
||||
/* Aliases as required by u-boot to patch MAC addresses */
|
||||
ethernet0 = &dp5;
|
||||
label-mac-device = &dp5;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system_red: system-red {
|
||||
label = "red:system";
|
||||
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_system_green: system-green {
|
||||
label = "green:system";
|
||||
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_system_blue: system-blue {
|
||||
label = "blue:system";
|
||||
gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pins {
|
||||
mdc {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "rootfs";
|
||||
reg = <0x0000000 0x3400000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-select = <0>;
|
||||
status = "ok";
|
||||
|
||||
m25p80@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
use-default-sizes;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:sbl1";
|
||||
reg = <0x0 0x50000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "0:mibib";
|
||||
reg = <0x50000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:bootconfig";
|
||||
reg = <0x60000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "0:bootconfig1";
|
||||
reg = <0x80000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@a0000 {
|
||||
label = "0:qsee";
|
||||
reg = <0xa0000 0x180000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@220000 {
|
||||
label = "0:qsee_1";
|
||||
reg = <0x220000 0x180000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3a0000 {
|
||||
label = "0:devcfg";
|
||||
reg = <0x3a0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3b0000 {
|
||||
label = "0:devcfg_1";
|
||||
reg = <0x3b0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3c0000 {
|
||||
label = "0:apdp";
|
||||
reg = <0x3c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3d0000 {
|
||||
label = "0:apdp_1";
|
||||
reg = <0x3d0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3e0000 {
|
||||
label = "0:rpm";
|
||||
reg = <0x3e0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@420000 {
|
||||
label = "0:rpm_1";
|
||||
reg = <0x420000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@460000 {
|
||||
label = "0:cdt";
|
||||
reg = <0x460000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@470000 {
|
||||
label = "0:cdt_1";
|
||||
reg = <0x470000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@480000 {
|
||||
label = "0:appsblenv";
|
||||
reg = <0x480000 0x10000>;
|
||||
};
|
||||
|
||||
partition@490000 {
|
||||
label = "0:appsbl";
|
||||
reg = <0x490000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@530000 {
|
||||
label = "0:appsbl_1";
|
||||
reg = <0x530000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5d0000 {
|
||||
label = "0:art";
|
||||
reg = <0x5d0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@610000 {
|
||||
label = "0:ethphyfw";
|
||||
reg = <0x610000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
|
||||
|
||||
qca8075: ethernet-phy@4 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x1e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x20>; /* wan port bitmap */
|
||||
switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
|
||||
switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
|
||||
bm_tick_mode = <0>; /* bm tick mode */
|
||||
tm_tick_mode = <0>; /* tm tick mode */
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
phy_address = <0>;
|
||||
};
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
phy_address = <1>;
|
||||
};
|
||||
port@2 {
|
||||
port_id = <3>;
|
||||
phy_address = <2>;
|
||||
};
|
||||
port@3 {
|
||||
port_id = <4>;
|
||||
phy_address = <3>;
|
||||
};
|
||||
port@4 {
|
||||
port_id = <5>;
|
||||
phy_address = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dp5 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075>;
|
||||
label = "lan";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath11k-calibration-variant = "Edimax-CAX1800";
|
||||
qcom,ath11k-fw-memory-mode = <1>;
|
||||
};
|
||||
|
|
@ -17,6 +17,19 @@ define Device/UbiFit
|
|||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
|
||||
define Device/edimax_cax1800
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Edimax
|
||||
DEVICE_MODEL := CAX1800
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_DTS_CONFIG := config@ac03
|
||||
SOC := ipq8070
|
||||
DEVICE_PACKAGES := ipq-wifi-edimax_cax1800
|
||||
endef
|
||||
TARGET_DEVICES += edimax_cax1800
|
||||
|
||||
define Device/redmi_ax6
|
||||
$(call Device/xiaomi_ax3600)
|
||||
DEVICE_VENDOR := Redmi
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user