Similar to wireguard, vxlan can configure multiple peers or add specific
entries to the fdb for a single mac address.
While you can still use peeraddr/peer6addr option within the proto
vxlan/vxlan6 section to not break existing configurations, this patch
allows to add multiple sections that conigure fdb entries via the bridge
command. As such, the bridge command is now a dependency of the vxlan
package. (To be honest without the bridge command available, vxlan isn't
very much fun to use or debug at all)
Field names are taken direclty from the bridge command.
Example with all supported parameters, since this hasn't been documented so
far:
config interface 'vx0'
option proto 'vxlan6' # use vxlan over ipv6
# main options
option ip6addr '2001:db8::1' # listen address
option tunlink 'wan6' # optional if listen address given
option peer6addr '2001:db8::2' # now optional
option port '8472' # this is the standard port under linux
option vid '42' # VXLAN Network Identifier to use
option mtu '1430' # vxlan6 has 70 bytes overhead
# extra options
option rxcsum '0' # allow receiving packets without checksum
option txcsum '0' # send packets without checksum
option ttl '16' # specifies the TTL value for outgoing packets
option tos '0' # specifies the TOS value for outgoing packets
option macaddr '11:22:33:44:55:66' # optional, manually specify mac
# default is a random address
Single peer with head-end replication. Corresponds to the following call
to bridge:
$ bridge fdb append 00:00:00:00:00:00 dev vx0 dst 2001:db8::3
config vxlan_peer
option vxlan 'vx0'
option dst '2001:db8::3' # always required
For multiple peers, this section can be repeated for each dst address.
It's possible to specify a multicast address as destination. Useful when
multicast routing is available or within one lan segment:
config vxlan_peer
option vxlan 'vx0'
option dst 'ff02::1337' # multicast group to join.
# all bum traffic will be send there
option via 'eth1' # for multicast, an outgoing interface needs
# to be specified
All available peer options for completeness:
config vxlan_peer
option vxlan 'vx0' # the interface to configure
option lladdr 'aa:bb:cc:dd:ee:ff' # specific mac,
option dst '2001:db8::4' # connected to this peer
option via 'eth0.1' # use this interface only
option port '4789' # use different port for this peer
option vni '23' # override vni for this peer
option src_vni '123' # see man 3 bridge
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
vxlan can be configured without a peer address. This is used to prepare
an interface and add peers later.
Fixes: FS#2743
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
Acked-by: Matthias Schiffer <mschiffer@universe-factory.net>
This fixes a nasty problem introduced in 2.81 which causes random
crashes on systems where there's significant DNS activity over TCP. It
also fixes DNSSEC validation problems with zero-TTL DNSKEY and DS
records.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This file is always present because it is part of the ltq-dsl-base
package on which these packages depend.
This check would not have been necessary in the past, because the script
was part of the TARGET_LANTIQ on which these packages also depend.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
It does not make sense to install this components on lantiq systems
where the dsl subsystem is not needed/used.
This also makes it possible to use the files also on other targets.
(hopefully ipq401x / FritzBox 7530 in the near future)
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
In the package guidelines, PKG_VERSION is supposed to be used as
"The upstream version number that we're downloading", while
PKG_RELEASE is referred to as "The version of this package Makefile".
Thus, the variables in a strict interpretation provide a clear
distinction between "their" (upstream) version in PKG_VERSION and
"our" (local OpenWrt trunk) version in PKG_RELEASE.
For local (OpenWrt-only) packages, this implies that those will only
need PKG_RELEASE defined, while PKG_VERSION does not apply following
a strict interpretation. While the majority of "our" packages actually
follow that scheme, there are also some that mix both variables or
have one of them defined but keep them at "1".
This is misleading and confusing, which can be observed by the fact
that there typically either one of the variables is never bumped or
the choice of the variable to increase depends on the person doing the
change.
Consequently, this patch aims at clarifying the situation by
consistently using only PKG_RELEASE for "our" packages. To achieve
that, PKG_VERSION is removed there, bumping PKG_RELEASE where
necessary to ensure the resulting package version string is bigger
than before.
During adjustment, one has to make sure that the new resulting composite
package version will not be considered "older" than the previous one.
A useful tool for evaluating that is 'opkg compare-versions'. In
principle, there are the following cases:
1. Sole PKG_VERSION replaced by sole PKG_RELEASE:
In this case, the resulting version string does not change, it's
just the value of the variable put in the file. Consequently, we
do not bump the number in these cases so nobody is tempted to
install the same package again.
2. PKG_VERSION and PKG_RELEASE replaced by sole PKG_RELEASE:
In this case, the resulting version string has been "version-release",
e.g. 1-3 or 1.0-3. For this case, the new PKG_RELEASE will just
need to be higher than the previous PKG_VERSION.
For the cases where PKG_VERSION has always sticked to "1", and
PKG_RELEASE has been incremented, we take the most recent value of
PKG_RELEASE.
Apart from that, a few packages appear to have developed their own
complex versioning scheme, e.g. using x.y.z number for PKG_VERSION
_and_ a PKG_RELEASE (qos-scripts) or using dates for PKG_VERSION
(adb-enablemodem, wwan). I didn't touch these few in this patch.
Cc: Hans Dedecker <dedeckeh@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Andre Valentin <avalentin@marcant.net>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Steven Barth <steven@midlink.org>
Cc: Daniel Golle <dgolle@allnet.de>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bumping package version has been overlooked in a previous commit.
While at it, use PKG_RELEASE instead of PKG_VERSION, as the latter
is meant for upstream version number only.
(The effective version string for the package would be "3" in both
cases, so there is no harm done for version comparison.)
Fixes: 0453c3866f ("vxlan: fix udp checksum control")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, passing "rxcsum" and "txcsum" had no effect.
Fixes: 95ab18e012 ("vxlan: add options to enable and disable UDP
checksums")
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Feature detection doesn't recognize ipset v7 use on kernel v5.x systems
and thus disables the tc ematch function em_ipset.
- backport patch:
* 002-configure-support-ipset-v7.patch:
650591a7a70c configure: support ipset version 7 with kernel version 5
Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Recent iproute2 5.x versions modified the symbols resolved for plugins,
causing "tc .. action xt .." to fail. Update the list of symbols to fix.
Fixes: b61495409b ("iproute2: tc: reduce size of dynamic symbol table")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This release brings parity with the commits Linus released a few hours
ago into 5.8-rc5.
* receive: account for napi_gro_receive never returning GRO_DROP
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands.
* device: implement header_ops->parse_protocol for AF_PACKET
WireGuard uses skb->protocol to determine packet type, and bails out if
it's not set or set to something it's not expecting. For AF_PACKET
injection, we need to support its call chain of:
packet_sendmsg -> packet_snd -> packet_parse_headers ->
dev_parse_header_protocol -> parse_protocol
Without a valid parse_protocol, this returns zero, and wireguard then
rejects the skb. So, this wires up the ip_tunnel handler for layer 3
packets for that case.
* queueing: make use of ip_tunnel_parse_protocol
Now that wg_examine_packet_protocol has been added for general
consumption as ip_tunnel_parse_protocol, it's possible to remove
wg_examine_packet_protocol and simply use the new
ip_tunnel_parse_protocol function directly.
* compat: backport ip_tunnel_parse_protocol and ip_tunnel_header_ops
These are required for moving wg_examine_packet_protocol out of
wireguard and into upstream.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
New script for comgt. Should help to fetch balance or any additional information with USSD.
This script uses the standard AT command which should be supported by all modems.
Run-tested on: Mikrotik wAP LTE KIT
Signed-off-by: Kirill Lukonin <klukonin@gmail.com>
[fixed from/sob]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upstream in commit 972d723484d8 ("split signkey_type and signature_type
for RSA sha1 vs sha256") has added strict checking of pubkey algorithms
which made keys with SHA-256 hashing algorithm unusable as they still
reuse the `ssh-rsa` public key format. So fix this by disabling the
check for `rsa-sha2-256` pubkeys.
Ref: https://tools.ietf.org/html/rfc8332#section-3
Fixes: d4c80f5b17 ("dropbear: bump to 2020.80")
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
/lib/netifd/dhcp.script:
Keep support for 'timesvr' while also supporting 'timesrv'
Add log message indicating deprecation of 'timesvr'
Signed-off-by: Sukru Senli <sukru.senli@iopsys.eu>
Backport patches which fix compile issue for uClibc-ng :
dbrandom.c:174:8: warning: implicit declaration of function 'getrandom'; did you mean 'genrandom'? [-Wimplicit-function-declaration]
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~
genrandom
dbrandom.c:174:36: error: 'GRND_NONBLOCK' undeclared (first use in this function); did you mean 'SOCK_NONBLOCK'?
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~~~~~
SOCK_NONBLOCK
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* compat: drop centos 8.1 support as 8.2 is now out
Of note, as well, is that we now have both RHEL7 and RHEL8 in our CI at
<https://www.wireguard.com/build-status/>.
* Kbuild: remove -fvisibility=hidden from cflags
This fixes an issue when compiling wireguard as a module for ARM kernels in
THUMB2 mode without the JUMP11 workaround.
* noise: do not assign initiation time in if condition
Style fix.
* device: avoid circular netns references
Fixes a circular reference issue with network namespaces.
* netns: workaround bad 5.2.y backport
This works around a back backport in the 5.2.y series.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
This follows up 3519bf4976
As a result, we also need to move the and/or out of the test brackets.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[squash from two patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- drop patches (applied upstream):
* 010-backport-change-address-logging.patch
* 020-backport-ed25519-support.patch
* 021-backport-chacha20-poly1305-support.patch
- backport patches:
* 010-backport-disable-toom-and-karatsuba.patch:
reduce dropbear binary size (about ~8Kb).
- refresh patches.
- don't bother anymore with following config options
because they are disabled in upstream too:
* DROPBEAR_3DES
* DROPBEAR_ENABLE_CBC_MODE
* DROPBEAR_SHA1_96_HMAC
- explicitly disable DO_MOTD as it was before commit a1099ed:
upstream has (accidentally) switched it to 0 in release 2019.77,
but reverted back in release 2020.79.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Ubus patch as it seems have been broken by some rebase in the past as
the location of line that adds ubus object file was in condition for
CONFIG_MACSEC. That condition was adding object files that are not
touched by ubus patch. This means ubus.o does not have to be included in
that case. When it has to be and when build fails is when CONFIG_AP is
set. All files included in wpa_supplicant that are touched by this patch
are in this condition. This means that this is for sure the original
place for it.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
After a hardware reconnect, the control device might be unavailable and
attempting to interact with it will lead to hanging gcom calls, leaving
the protocol setup in an unrecoverable state.
Change the protocol handler to bail out early and notify netifd if the
control device is not defined or if the underlying device node does not
exist.
Also ensure that the "disconnect", "connect" and "setmode" commands are
actually defined before trying to invoke them.
Finally attempt to re-query the device manufacturer if it is unset in
the interface state in order to prevent UNUPPORTED_MODEM errors after
a modem hardware reconnect.
Signed-off-by: Rozhuk Ivan <rozhuk.im@gmail.com>
[reword subject and commit message]
Ref: https://github.com/openwrt/openwrt/pull/2352
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Pass a default --up and --down executable to each started OpenVPN instance
which triggers /etc/hotplug.d/openvpn/ scripts whenever an instance
goes up or down.
User-configured up and down scripts are invoked by the default shipped
01-user hotplug handler to ensure that existing setups continue to work
as before.
As a consequence of this change, the up, down and script_security OpenVPN
options are removed from the option file, since we're always passing them
via the command line, they do not need to get included into the generated
configuration.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[reword commit message, move hotplug executable to /usr/libexec]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Bringing up of station vlan fails if the optional mac entry isn't set.
The default mac "00:00:00:00:00:00", which should match all stations,
is mistakenly set to the non used variable "isolate". This results in
a wrong formatted .psk file which has to be "vlan_id mac key".
fixes: 5aa2ddd0: hostapd: add support for wifi-station and wifi-vlan sections
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
IPKG_INSTROOT is only set under image builder and we won't be running
this script at build time either, so remove the reference before it gets
cargo-culted into other scripts.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
The folder for the uci-defaults file of this package is wrong, so
the file most probably has not been executed at all for several
years at least.
Fix the folder and remove the useless shebang for the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bump to latest Git and refresh all patches in order to get fix for "UPnP
SUBSCRIBE misbehavior in hostapd WPS AP" (CVE-2020-12695).
General security vulnerability in the way the callback URLs in the UPnP
SUBSCRIBE command are used were reported (VU#339275, CVE-2020-12695).
Some of the described issues may be applicable to the use of UPnP in WPS
AP mode functionality for supporting external registrars.
Ref: https://w1.fi/security/2020-1/
Signed-off-by: Petr Štetiar <ynezz@true.cz>
d13290b Fix advertised IPv6 addresses
Don't just serve link-local addresses via mdns, offer all.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When bringing up wifi the first time after boot, these warnings appear:
netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.psk': No such file or directory
netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.vlan': No such file or directory
Silence them by adding the "-f" option to rm.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
This patch adds support for 2 new uci sections.
config wifi-vlan
# iface is optional. if it is not defined the vlan will apply
# to all interfaces
option iface default_radio0
option name guest
option vid 100
option network guest
config wifi-station
# iface is optional. if it is not defined the station will apply
# to all interfaces
option iface default_radio0
# mac is optional. if it is not defined it will be a catch all
# for any sta using this key
option mac '00:11:22:33:44:55'
# vid is optional. if it is not defined, the sta will be part of
# the primary iface.
option vid 100
option key testtest
With this patch applied it is possible to use multiple PSKs on a single BSS.
Signed-off-by: John Crispin <john@phrozen.org>
db275e1 interface-ip: fix build on non-linux systems
3392046 system-dummy: fix missing return
a56b457 netifd: wireless: add support for tracking wifi-station sections
4ce33ce netifd: wireless: add support for tracking wifi-vlan sections
Signed-off-by: John Crispin <john@phrozen.org>
ddd57c2 pppd: Add lcp-echo-adaptive option
c319558 pppd: Handle SIGINT and SIGTERM during interrupted syscalls (#148)
0bc11fb Added missing options to manual pages. (#149)
b1fcf16 Merge branch 'monotonic-time' of https://github.com/themiron/ppp
c78e312 pppd: linux: use monotonic time if possible
Remove patch 121-debian_adaptive_lcp_echo as patch is upstream accepted
Remove patch 206-compensate_time_change.patch as timewrap issues are
solved by a patch making use of monotonic time
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Also ensure that the error message is actually printed to stderr and that
the rule generation is aborted if an interface cannot be resolved.
Ref: https://github.com/openwrt/luci/issues/3975
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
disable_vht parameter needs to be set when using wpa_supplicant NOHT/HT* modes.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Commit 472fd98c5b ("hostapd: disable support for Wired Equivalent
Privacy by default") made support for WEP optional.
Expose the WEP support to LuCi or other userspace tools using the
existing interface. This way they are able to remove WEP from the
available ciphers if hostapd is built without WEP support.
Signed-off-by: David Bauer <mail@david-bauer.net>
Running your firewall's "wan" zone in REJECT zone (1) exposes the
presence of the router, (2) depending on the sophistication of
fingerprinting tools might identify the OS and release running on
the firewall which then identifies known vulnerabilities with it
and (3) perhaps most importantly of all, your firewall can be
used in a DDoS reflection attack with spoofed traffic generating
ICMP Unreachables or TCP RST's to overwhelm a victim or saturate
his link.
This rule, when enabled, allows traceroute to work even when the
default input policy of the firewall for the wan zone has been
set to DROP.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
The 131-Revert-mac80211-aes-cmac-switch-to-shash-CMAC-driver.patch patch
was manually adapted to the changes in kernel 5.7.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bring back 802.11s mesh features to the level previously available
before the recent hostapd version bump. This is mostly to support use
of 802.11s on DFS channels, but also making mesh forwarding
configurable which is crucial for use of 802.11s MAC with other routing
protocols, such as batman-adv, on top.
While at it, fix new compiler warning by adapting 700-wifi-reload.patch
to upstream changes, now building without any warnings again.
Fixes: 0a3ec87a66 ("hostapd: update to latest Git hostap_2_9-1238-gdd2daf0848ed")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This version has the various slew of bug fixes and compat fixes and
such, but the most interesting thing from an OpenWRT perspective is that
WireGuard now plays nicely with cake and fq_codel. I'll be very
interested to hear from OpenWRT users whether this makes a measurable
difference. Usual set of full changes follows.
This release aligns with the changes I sent to DaveM for 5.7-rc7 and were
pushed to net.git about 45 minutes ago.
* qemu: use newer iproute2 for gcc-10
* qemu: add -fcommon for compiling ping with gcc-10
These enable the test suite to compile with gcc-10.
* noise: read preshared key while taking lock
Matt noticed a benign data race when porting the Linux code to OpenBSD.
* queueing: preserve flow hash across packet scrubbing
* noise: separate receive counter from send counter
WireGuard now works with fq_codel, cake, and other qdiscs that make use of
skb->hash. This should significantly improve latency spikes related to
buffer bloat. Here's a before and after graph from some data Toke measured:
https://data.zx2c4.com/removal-of-buffer-bloat-in-wireguard.png
* compat: support RHEL 8 as 8.2, drop 8.1 support
* compat: support CentOS 8 explicitly
* compat: RHEL7 backported the skb hash renamings
The usual RHEL churn.
* compat: backport renamed/missing skb hash members
The new support for fq_codel and friends meant more backporting work.
* compat: ip6_dst_lookup_flow was backported to 4.14, 4.9, and 4.4
The main motivation for releasing this now: three stable kernels were released
at the same time, with a patch that necessitated updating in our compat layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Upstream in commit 200c7693c9a1 ("Make WEP functionality an optional
build parameter") has made WEP functionality an optional build parameter
disabled as default, because WEP should not be used for anything
anymore. As a step towards removing it completely, they moved all WEP
related functionality behind CONFIG_WEP blocks and disabled it by
default.
This functionality is subject to be completely removed in a future
release.
So follow this good security advice, deprecation notice and disable WEP
by default, but still allow custom builds with WEP support via
CONFIG_WPA_ENABLE_WEP config option till upstream removes support for
WEP completely.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Bump package to latest upstream Git HEAD which is commit dd2daf0848ed
("HE: Process HE 6 GHz band capab from associating HE STA"). Since last
update there was 1238 commits done in the upstream tree with 618 files
changed, 53399 insertions, 24928 deletions.
I didn't bothered to rebase mesh patches as the changes seems not
trivial and I don't have enough knowledge of those parts to do/test that
properly, so someone else has to forward port them, ideally upstream
them so we don't need to bother anymore. I've just deleted them for now:
004-mesh-use-setup-completion-callback-to-complete-mesh-.patch
005-mesh-update-ssid-frequency-as-pri-sec-channel-switch.patch
006-mesh-inform-kernel-driver-DFS-handler-in-userspace.patch
007-mesh-apply-channel-attributes-before-running-Mesh.patch
011-mesh-Allow-DFS-channels-to-be-selected-if-dfs-is-ena.patch
013-mesh-do-not-allow-pri-sec-channel-switch.patch
015-mesh-do-not-use-offchan-mgmt-tx-on-DFS.patch
016-mesh-fix-channel-switch-error-during-CAC.patch
018-mesh-make-forwarding-configurable.patch
Refreshed all other patches, removed upstreamed patches:
051-wpa_supplicant-fix-race-condition-in-mesh-mpm-new-pe.patch
067-0001-AP-Silently-ignore-management-frame-from-unexpected-.patch
070-driver_nl80211-fix-WMM-queue-mapping-for-regulatory-.patch
071-driver_nl80211-fix-regulatory-limits-for-wmm-cwmin-c.patch
090-wolfssl-fix-crypto_bignum_sum.patch
091-0001-wolfssl-Fix-compiler-warnings-on-size_t-printf-forma.patch
091-0002-wolfssl-Fix-crypto_bignum_rand-implementation.patch
091-0003-wolfssl-Do-not-hardcode-include-directory-in-wpa_sup.patch
800-usleep.patch
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/NBG6817; ipq40xx/MAP-AC2200]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipc: add support for openbsd kernel implementation
* ipc: cleanup openbsd support
* wg-quick: add support for openbsd kernel implementation
* wg-quick: cleanup openbsd support
Very exciting! wg(8) and wg-quick(8) now support the kernel implementation for
OpenBSD. OpenBSD is the second kernel, after Linux, to receive full fledged
and supported WireGuard kernel support. We'll probably send our patch set up
to the list during this next week. `ifconfig wg0 create` to make an interface,
and `wg ...` like usual to configure WireGuard aspects of it, like usual.
* wg-quick: support dns search domains
If DNS= has a non-IP in it, it is now treated as a search domain in
resolv.conf. This new feature will be rolling out across our various GUI
clients in the next week or so.
* Makefile: simplify silent cleaning
* ipc: remove extra space
* git: add gitattributes so tarball doesn't have gitignore files
* terminal: specialize color_mode to stdout only
Small cleanups.
* highlighter: insist on 256-bit keys, not 257-bit or 258-bit
The highlighter's key checker is now stricter with base64 validation.
* wg-quick: android: support application whitelist
Android users can now have an application whitelist instead of application
blacklist.
* systemd: add wg-quick.target
This enables all wg-quick at .services to be restarted or managed as a unit via
wg-quick.target.
* Makefile: remember to install all systemd units
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
crypto_bignum_rand() use needless time-consuming filtering
which resulted in SAE no longer connecting within time limits.
Import fixes from hostap upstream to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hotplug scripts are sourced so the #!/bin/sh is superfluous/deceptive.
Re-arrange script to only source 'procd' if we get to the stage of
needing to signal the process, reduce hotplug processing load a little.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
add option to set management IP pattern
also add missing 'unconfigure system hostname'
for example pattern '!192.168.1.1' makes it possible that
WAN IP is selected instead of LAN IP
Signed-off-by: Daniel A. Maierhofer <git@damadmai.at>
[grammar and spelling fixes in commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Samba 3.6 is completely unsupported, in addition to having tons of patches
It also causes kernel panics on some platforms when sendfile is enabled.
Example:
https://github.com/gnubee-git/GnuBee_Docs/issues/45
I have reproduced on ramips as well as mvebu in the past.
Samba 4 is an alternative available in the packages repo.
cifsd is a lightweight alternative available in the packages repo. It is
also a faster alternative to both Samba versions (lower CPU usage). It
was renamed to ksmbd.
To summarize, here are the alternatives:
- ksmbd + luci-app-cifsd
- samba4 + luci-app-samba4
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[drop samba36-server from GEMINI_NAS_PACKAGES, ksmbd rename + summary]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* compat: timeconst.h is a generated artifact
Before we were trying to check for timeconst.h by looking in the kernel
source directory. This isn't quite correct on configurations in which
the object directory is separate from the kernel source directory, for
example when using O="elsewhere" as a make option when building the
kernel. The correct fix is to use $(CURDIR), which should point to
where we want.
* compat: use bash instead of bc for HZ-->USEC calculation
This should make packaging somewhat easier, as bash is generally already
available (at least for dkms), whereas bc isn't provided by distros by
default in their build meta packages.
* socket: remove errant restriction on looping to self
It's already possible to create two different interfaces and loop
packets between them. This has always been possible with tunnels in the
kernel, and isn't specific to wireguard. Therefore, the networking stack
already needs to deal with that. At the very least, the packet winds up
exceeding the MTU and is discarded at that point. So, since this is
already something that happens, there's no need to forbid the not very
exceptional case of routing a packet back to the same interface; this
loop is no different than others, and we shouldn't special case it, but
rather rely on generic handling of loops in general. This also makes it
easier to do interesting things with wireguard such as onion routing.
At the same time, we add a selftest for this, ensuring that both onion
routing works and infinite routing loops do not crash the kernel. We
also add a test case for wireguard interfaces nesting packets and
sending traffic between each other, as well as the loop in this case
too. We make sure to send some throughput-heavy traffic for this use
case, to stress out any possible recursion issues with the locks around
workqueues.
* send: cond_resched() when processing tx ringbuffers
Users with pathological hardware reported CPU stalls on CONFIG_
PREEMPT_VOLUNTARY=y, because the ringbuffers would stay full, meaning
these workers would never terminate. That turned out not to be okay on
systems without forced preemption. This commit adds a cond_resched() to
the bottom of each loop iteration, so that these workers don't hog the
core. We don't do this on encryption/decryption because the compat
module here uses simd_relax, which already includes a call to schedule
in preempt_enable.
* selftests: initalize ipv6 members to NULL to squelch clang warning
This fixes a worthless warning from clang.
* send/receive: use explicit unlikely branch instead of implicit coalescing
Some code readibility cleanups.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* compat: support latest suse 15.1 and 15.2
* compat: support RHEL 7.8's faulty siphash backport
* compat: error out if bc is missing
* compat: backport hsiphash_1u32 for tests
We now have improved support for RHEL 7.8, SUSE 15.[12], and Ubuntu 16.04.
* compat: include sch_generic.h header for skb_reset_tc
A fix for a compiler error on kernels with weird configs.
* compat: import latest fixes for ptr_ring
* compat: don't assume READ_ONCE barriers on old kernels
* compat: kvmalloc_array is not required anyway
ptr_ring.h from upstream was imported, with compat modifications, to our
compat layer, to receive the latest fixes.
* compat: prefix icmp[v6]_ndo_send with __compat
Some distros that backported icmp[v6]_ndo_send still try to build the compat
module in some corner case circumstances, resulting in errors. Work around
this with the usual __compat games.
* compat: ip6_dst_lookup_flow was backported to 3.16.83
* compat: ip6_dst_lookup_flow was backported to 4.19.119
Greg and Ben backported the ip6_dst_lookup_flow patches to stable kernels,
causing breaking in our compat module, which these changes fix.
* git: add gitattributes so tarball doesn't have gitignore files
Distros won't need to clean this up manually now.
* crypto: do not export symbols
These don't do anything and only increased file size.
* queueing: cleanup ptr_ring in error path of packet_queue_init
Sultan Alsawaf reported a memory leak on an error path.
* main: mark as in-tree
Now that we're upstream, there's no need to set the taint flag.
* receive: use tunnel helpers for decapsulating ECN markings
ECN markings are now decapsulated using RFC6040 instead of the old RFC3168.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Init script checks for an already active DHCP server on the interface
and if such DHCP server is found, then it logs "refusing to start DHCP"
message, starts dnsmasq without DHCP service unless `option force 1` is
set and caches the DHCP server check result.
Each consecutive service start then uses this cached DHCP server check
result, but doesn't provide log feedback about disabled DHCP service
anymore.
So this patch ensures, that the log message about disabled DHCP service
on particular interface is always provided.
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Backport patch from hostapd.git master that fixes copy/paste error in
crypto_bignum_sub() in crypto_wolfssl.c.
This missing fix was discovered while testing SAE over a mesh interface.
With this fix applied and wolfssl >3.14.4 mesh+SAE works fine with
wpad-mesh-wolfssl.
Cc: Sean Parkinson <sean@wolfssl.com>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
f4d759b dhcp.c: further improve validation
Further improve input validation for CVE-2020-11752
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
cdac046 dns.c: fix input validation fix
Due to a slight foobar typo, failing to de-reference a pointer, previous
fix not quite as complete as it should have been.
Improve CVE-2020-11750 fix
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When compiled with glibc the config_scan.c wants to use the
cpupolicy2numeric() function which is only available when
HAVE_SCHED_SETSCHEDULER is set. It looks like the wrong define was used here.
This fixes a build problem with glibc in combination with the force
ac_cv_func_sched_setscheduler=no in the OpenWrt CONFIGURE_VARS.
This fixes the following compile error with glibc:
----------------------------------------------------------------------
/bin/ld: config_scan.o: in function `socks_yylex':
dante-1.4.1/sockd/config_scan.l:461: undefined reference to `cpupolicy2numeric'
collect2: error: ld returned 1 exit status
make[5]: *** [Makefile:522: sockd] Error 1
Fixes: aaf46a8fe2 ("dante: disable sched_getscheduler() - not implemented in musl")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is primarily a maintenance release with bugfixes and improvements.
This release also fixes a security issue (CVE-2020-11810) which allows
disrupting service of a freshly connected client that has not yet
negotiated session keys. The vulnerability cannot be used to
inject or steal VPN traffic.
Release announcement:
https://openvpn.net/community-downloads/#heading-13812
Full list of changes:
https://community.openvpn.net/openvpn/wiki/ChangesInOpenvpn24#OpenVPN2.4.9
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
The previous commit introduced a regression for netns jails without
jail_ifname set. Fix that.
Fixes: 4e4f7c6d2d ("netifd: network namespace jail improvements")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
aaaca2e interface: allocate and free memory for jail name
d93126d interface: allow renaming interface when moving to jail netns
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CONFIG_WRITE functionality is not used and could be removed.
Looks helpful for devices with small flash because wpad is also affected.
Little testing shows that about 6 KB could be saved.
Signed-off-by: Kirill Lukonin <klukonin@gmail.com>
Since linux kernel commit 0768e17073dc527ccd18ed5f96ce85f9985e9115
(2019-04-19) the asm-generic/sockios.h header no longer defines
SIOCGSTAMP. Instead it provides only SIOCGSTAMP_OLD.
The linux/sockios.h header now defines SIOCGSTAMP using either
SIOCGSTAMP_OLD or SIOCGSTAMP_NEW as appropriate. This linux only
header file is not included so we get a build failure.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Allows proper usage of the ss tool. Otherwise, several errors and bad
data gets thrown:
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Originally reported here: https://github.com/openwrt/packages/issues/8232
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Use upstream latest git HEAD as it allows to remove the patches
700-radius-Prevent-buffer-overflow-in-rc_mksid,
701-pppd-Fix-bounds-check-in-EAP-code and
702-pppd-Ignore-received-EAP-messages-when-not-doing-EAP and
take in other fixes.
41a7323 pppd: Fixed spelling 'unkown' => 'unknown' (#141)
6b014be pppd: Print version information to stdout instead of stderr (#133)
cba2736 pppd: Add RFC1990 (Multilink) to the See Also section of the man page
f2f9554 pppd: Add mppe.h to the list of headers to install if MPPE is defined
ae54fcf pppd: Obfuscate password argument string
8d45443 pppd: Ignore received EAP messages when not doing EAP
8d7970b pppd: Fix bounds check in EAP code
858976b radius: Prevent buffer overflow in rc_mksid()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Bump to 2.81rc5 and re-work ipset-remove-old-kernel-support.
More runtime kernel version checking is done in 2.81rc5 in various parts
of the code, so expand the ipset patch' scope to inlude those new areas
and rename to something a bit more generic.:wq
Upstream changes from rc4
532246f Tweak to DNSSEC logging.
8caf3d7 Fix rare problem allocating frec for DNSSEC.
d162bee Allow overriding of ubus service name.
b43585c Fix nameserver list in auth mode.
3f60ecd Fixed resource leak on ubus_init failure.
0506a5e Handle old kernels that don't do NETLINK_NO_ENOBUFS.
e7ee1aa Extend stop-dns-rebind to reject IPv6 LL and ULA addresses. We also reject the loopback address if rebind-localhost-ok is NOT set.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
201e359 Handle early exit when addrstring isn't set
fa4c464 Improve address logging on early exit messages (#83)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
It seemed very confusing when trying to select the different variants of
hostapd which are somewhat scattered about under the menu 'Network'.
Moving all hostapd variants under a common submenu helps avoid
confusion.
Inspired-by: Kevin Mahoney <kevin.mahoney@zenotec.net>
[Fixup badly formatted patch, change menu name]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ab7a39a umdns: fix unused error
45c4953 dns: explicitly endian-convert all fields in header and question
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
gcc 8 & 9 appear to be more picky with regards access alignment to
packed structures, leading to this warning in dns.c:
dns.c:261:2: error: converting a packed ‘struct dns_question’ pointer
(alignment 1) to a ‘uint16_t’ {aka ‘short unsigned int’} pointer
(alignment 2) may result in an unaligned pointer value
[-Werror=address-of-packed-member]
261 | uint16_t *swap = (uint16_t *) q;
Work around what I think is a false positive by turning the warning off.
Not ideal, but not quite as not ideal as build failure.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Recent backports to 5.5 and 5.4 broke our compat layer. This release is
to keep things running with the latest upstream stable kernels.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* queueing: backport skb_reset_redirect change from 5.6
* version: bump
This release has only one slight change, to put it closer to the 5.6
codebase, but its main purpose is to bump us to a 1.0.y version number.
Now that WireGuard 1.0.0 has been released for Linux 5.6 [1], we can put
the same number on the backport compat codebase.
When OpenWRT bumps to Linux 5.6, we'll be able to drop this package
entirely, which I look forward to seeing.
[1] https://lists.zx2c4.com/pipermail/wireguard/2020-March/005206.html
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
If the abridged flag is set to 1 the APs that are listed in the BSS
Transition Candidate List are prioritized. If the bit is not set, the
APs have the same prioritization as the APs that are not in the list.
If you want to steer a client, you should set the flag!
The flag can be set by adding {...,'abridged': true,...} to the normal
ubus call.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Subscribe to beacon reports through ubus.
Can be used for hearing map and client steering purposes.
First enable rrm:
ubus call hostapd.wlan0 bss_mgmt_enable '{"beacon_report":True}'
Subscribe to the hostapd notifications via ubus.
Request beacon report:
ubus call hostapd.wlan0 rrm_beacon_req
'{"addr":"00:xx:xx:xx:xx:xx", "op_class":0, "channel":1,
"duration":1,"mode":2,"bssid":"ff:ff:ff:ff:ff:ff", "ssid":""}'
Signed-off-by: Nick Hainke <vincent@systemli.org>
[rework identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
Replace the build time choice of json support with a package based
choice. Users requiring a json aware version of 'nft' may now install
nftables-json.
The default choice to fulfill the 'nftables' package dependency is
'nftables-nojson'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When some libopenssl options change curl will have to be rebuild to
adapt to those changes, avoiding undefined reference errors or features
disabled in curl.
Add CONFIG_OPENSSL_ENGINE, CONFIG_OPENSSL_WITH_COMPRESSION and
CONFIG_OPENSSL_WITH_NPN to PKG_CONFIG_DEPENDS so it will trigger
rebuild every time the options are changed.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Fix the test for an enabled sysntp initscript in dnsmasq.init, and get
rid of "test -o" while at it.
Issue reproduced on openwrt-19.07 with the help of pool.ntp.br and an
RTC-less ath79 router. dnssec-no-timecheck would be clearly missing
from /var/etc/dnsmasq.conf.* while the router was still a few days in
the past due to non-working DNSSEC + DNS-based NTP server config.
The fix was tested with the router in the "DNSSEC broken state": it
properly started dnsmasq in dnssec-no-timecheck mode, and eventually ntp
was able to resolve the server name to an IP address, and set the system
time. DNSSEC was then enabled by SIGINT through the ntp hotplug hook,
as expected.
A missing system.ntp.enabled UCI node is required for the bug to show
up. The reasons for why it would be missing in the first place were not
investigated.
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Refer to shellcheck SC2166. There are just too many caveats that are
shell-dependent on test -a and test -o to use them.
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
Add option 'scriptarp' to uci dnsmasq config to enable --script-arp functions.
The default setting is false, meaning any scripts in `/etc/hotplug.d/neigh` intended
to be triggered by `/usr/lib/dnsmasq/dhcp-script.sh` will fail to execute.
Also enable --script-arp if has_handlers returns true.
Signed-off-by: Jordan Sokolic <oofnik@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
9f5a7c4 iwinfo: add missing HT modename for HT-None
06a03c9 Revert "iwinfo: add BSS load element to scan result"
9a4bae8 iwinfo: add device id for Qualcomm Atheros QCA9990
eba5a20 iwinfo: add device id for BCM43602
a6914dc iwinfo: add BSS load element to scan result
bb21698 iwinfo: add device id for Atheros AR9287
7483398 iwinfo: add device id for MediaTek MT7615E
Signed-off-by: David Bauer <mail@david-bauer.net>
WireGuard had a brief professional security audit. The auditors didn't find
any vulnerabilities, but they did suggest one defense-in-depth suggestion to
protect against potential API misuse down the road, mentioned below. This
compat snapshot corresponds with the patches I just pushed to Dave for
5.6-rc7.
* curve25519-x86_64: avoid use of r12
This buys us 100 extra cycles, which isn't much, but it winds up being even
faster on PaX kernels, which use r12 as a RAP register.
* wireguard: queueing: account for skb->protocol==0
This is the defense-in-depth change. We deal with skb->protocol==0 just fine,
but the advice to deal explicitly with it seems like a good idea.
* receive: remove dead code from default packet type case
A default case of a particular switch statement should never be hit, so
instead of printing a pretty debug message there, we full-on WARN(), so that
we get bug reports.
* noise: error out precomputed DH during handshake rather than config
All peer keys will now be addable, even if they're low order. However, no
handshake messages will be produced successfully. This is a more consistent
behavior with other low order keys, where the handshake just won't complete if
they're being used anywhere.
* send: use normaler alignment formula from upstream
We're trying to keep a minimal delta with upstream for the compat backport.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* netlink: initialize mostly unused field
* curve25519: squelch warnings on clang
Code quality improvements.
* man: fix grammar in wg(8) and wg-quick(8)
* man: backlink wg-quick(8) in wg(8)
* man: add a warning to the SaveConfig description
Man page improvements. We hope to rewrite our man pages in mdocml at some
point soon.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
When introducing ubus reload support, ubus initialization was moved
to the service level instead of being carried out when adding a BSS
configuration. While this works when using wpa_supplicant in that way,
it breaks the ability to run wpa_supplicant on the command line, eg.
for debugging purposes.
Fix that by re-introducing ubus context intialization when adding
configuration.
Reported-by: @PolynomialDivision https://github.com/openwrt/openwrt/pull/2417
Fixes: 60fb4c92b6 ("hostapd: add ubus reload")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit a6da3f9ef7.
The libcap isn't as optional as the commit messages suggests. A hard
dependency to the libcap package is added, which is only available in
the external packages feed. Therefore it is impossible to package
ip-full without having the external packages feed up and running, which
is a regression to the former behaviour.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
6594c6b ubus: use dhcpv6 ia assignment flag
a90cc2e dhcpv6-ia: avoid setting lifetime to infinite for static assignments
bb07fa4 dhcpv4: avoid setting lifetime to infinite for static assignments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Bump to iptable 1.8.4 and address packaging issue as mentioned in the
original bump/revert cycle.
"This reverts commit 10cbc896c0.
The updated iptables package does not build due to the following error
encountered on the buildbots:
cp: cannot stat '.../iptables-1.8.4/ipkg-install/usr/lib/libiptc.so.*': No such file or directory
The changelog mentions "build: remove -Wl,--no-as-needed and libiptc.so" so
it appears as if further packaging changes are needed beyond a simple
version bump."
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Bump to latest release candidate and drop 2 local patches that have been
upstreamed.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Bump to dnsmasq 2.81rc2. In the process discovered several compiler
warnings one with a logical error.
2 relevant patches sent upstream, added as 2 local patches for OpenWrt
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
1st release candidate for v2.81 after 18 months.
Refresh patches & remove all upstreamed leaving:
110-ipset-remove-old-kernel-support.patch
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The current implementation is significantly lowering lantiq
performace [1][2] by using RPS with non-irq CPUs and XPS
with alternating CPUs.
The previous netifd implementation (by default but could be
configured) simply used all CPUs and this patch essentially
reverts to this behaviour.
The only document suggesting using non-interrupt CPUs is Red
Hat [3] where if the network interrupt rate is extremely high
excluding the CPU that handles network interrupts *may* also
improve performance.
The original packet steering patches [4] advise that optimal
settings for the CPU mask seems to depend on architectures
and cache hierarcy so one size does not fit all. It also
advises that the overhead in processing for a lightly loaded
server can cause performance degradation.
Ideally, proper IRQ balancing is a better option with
the irqbalance daemon or manually.
The kernel does not enable packet steering by default, so
also disable in OpenWRT by default. (Though mvebu with its
hardware scheduling issues [5] might want to enable packet
steering by default.)
Change undocumented "default_ps" parameter to clearer
"packet_steering" parameter. The old parameter was only ever
set in target/linux/mediatek/base-files/etc/uci-defaults/99-net-ps
and matched the default.
[1] https://forum.openwrt.org/t/18-06-4-speed-fix-for-bt-homehub-5a
[2] https://openwrt.ebilan.co.uk/viewtopic.php?f=7&t=1105
[3] https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/6/html/performance_tuning_guide/network-rps
[4] https://marc.info/?l=linux-netdev&m=125792239522685&w=2
[5] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=2e1f6f1682d3974d8ea52310e460f1bbe470390fFixes: #1852Fixes: #2573
Signed-off-by: Alan Swanson <reiver@improbability.net>
This activates PIE ASLR support by default when the regular option is
selected.
Size increase on imx6:
112681 ppp_2.4.8-2_arm_cortex-a9_neon.ipk
121879 ppp_2.4.8-2_arm_cortex-a9_neon.ipk
= 9198 diff
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 215598fd03 since it
didn't contain a reference to the CVE it addresses. The next commit
will re-add the commit including a CVE reference in its commit message.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add a radio_config_id property. If the radio config changes return an error
upon receiving the reconf call.
Signed-off-by: John Crispin <john@phrozen.org>
c888e17e06 ("hostapd: manage instances via procd instead of pidfile")
added procd support for managing hostapd and wpa_supplicant daemons
but at the same time limited wiphy names to 'phy*'.
This brings back initial behaviour (introduced in 60fb4c92b6 ("hostapd:
add ubus reload") and makes procd manage daemons for any wiphy device
found in '/sys/class/ieee80211'.
CC: Felix Fietkau <nbd@nbd.name>
CC: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The function trace_on_exit() is given to atexit() as a parameter, but
atexit() only takes a function pointer to a function with a void
parameter.
This problem was introduced when the on_exit() function was incompletely
replaced by atexit().
Fixes: ba6c8bd614 ("linux-atm: add portability fixes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the direct dependencies introduced by TARGET_LDFLAGS
to the package's DEPENDS variable.
This was found by accidentally building rssileds on octeon, which
resulted in:
"Package rssileds is missing dependencies for the following libraries:
libnl-tiny.so"
Though the dependencies are provided when building for the
relevant targets ar71xx, ath79 and ramips, it seems more tidy to
specify them explicitly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
8d45443bb5c9 pppd: Ignore received EAP messages when not doing EAP
8d7970b8f3db pppd: Fix bounds check in EAP code
858976b1fc31 radius: Prevent buffer overflow in rc_mksid()
Signed-off-by: Petr Štetiar <ynezz@true.cz>
A file, package/network/services/dnsmasq/files/50-dnsmasq-migrate-resolv-conf-auto.sh,
was added in commit 6a28552120, but it
does not exit in a way that tells the uci-defaults mechanism that it
succeeded, and so it is not cleaned up after running successfully. Add
an exit 0 to the end to correct that.
Signed-off-by: Russell Senior <russell@personaltelco.net>
* send: cleanup skb padding calculation
* socket: remove useless synchronize_net
Sorry for the back-to-back releases. This fixes a regression spotted by Eric
Dumazet.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* wg-quick: android: split uids into multiple commands
Newer android's ndc implementations have limits on uid size, so we have to
break these into several lists.
* man: document dynamic debug trick for Linux
This comes up occasionally, so it may be useful to mention its
possibility in the man page. At least the Arch Linux and Ubuntu kernels
support dynamic debugging, so this advice will at least help somebody. So that
you don't have to go digging into the commit, this adds this helpful tidbit
to the man page for getting debug logs on Linux:
# modprobe wireguard && echo module wireguard +p > /sys/kernel/debug/dynamic_debug/control
* extract-{handshakes,keys}: rework for upstream kernel
These tools will now use the source code from the running kernel instead of
from the old monolithic repo. Essential for the functioning of Wireshark.
* netlink: remove libmnl requirement
We no longer require libmnl. It turns out that inlining the small subset of
libmnl that we actually use results in a smaller binary than the overhead of
linking to the external library. And we intend to gradually morph this code
into something domain specific as a libwg emerges. Performance has also
increased, thanks to the inliner. On all platforms, wg(8) only needs a normal
libc. Compile time on my system is still less than one second. So all in all
we have: smaller binary, zero dependencies, faster performance.
Packagers should no longer have their wireguard-tools package depend on
libmnl.
* embeddable-wg-library: use newer string_list
* netlink: don't pretend that sysconf isn't a function
Small cleanups.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The $(space) definition in the hostapd Makefile ceased to work with
GNU Make 4.3 and later, leading to syntax errors in the generated
Kconfig files.
Drop the superfluous redefinition and reuse the working $(space)
declaration from rules.mk to fix this issue.
Fixes: GH#2713
Ref: https://github.com/openwrt/openwrt/pull/2713#issuecomment-583722469
Reported-by: Karel Kočí <cynerd@email.cz>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Shaleen Jain <shaleen@jain.sh>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* compat: support building for RHEL-8.2
* compat: remove RHEL-7.6 workaround
Bleeding edge RHEL users should be content now (which includes the actual
RedHat employees I've been talking to about getting this into the RHEL kernel
itself). Also, we remove old hacks for versions we no longer support anyway.
* allowedips: remove previously added list item when OOM fail
* noise: reject peers with low order public keys
With this now being upstream, we benefit from increased fuzzing coverage of
the code, uncovering these two bugs.
* netns: ensure non-addition of peers with failed precomputation
* netns: tie socket waiting to target pid
An added test to our test suite for the above and a small fix for high-load CI
scenarios.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This reverts commit 96424c143d.
The commit changed libiwinfo's internal ABI which breaks a number of
downstream projects, including LuCI and rpcd-mod-iwinfo.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
eba5a20 iwinfo: add device id for BCM43602
a6914dc iwinfo: add BSS load element to scan result
bb21698 iwinfo: add device id for Atheros AR9287
7483398 iwinfo: add device id for MediaTek MT7615E
Signed-off-by: David Bauer <mail@david-bauer.net>
I'm having another attempt at trying to getting the 'store dscp into
conntrack connmark' functionality into upstream kernel, since the
restore function (act_ctinfo) has been accepted.
The syntax has changed from 'savedscp' to 'set-dscpmark' since that
conforms more closely with existing functionality.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fixes handling CSA when using AP+STA or AP+Mesh
This change was accidentally dropped in commit 167028b75
("hostapd: Update to version 2.9 (2019-08-08)")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Without this change, wpa-cli features depend on which wpad build variant was
used to build the wpa-cli package
Signed-off-by: Felix Fietkau <nbd@nbd.name>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[remove shebang, slightly facelift commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* Makefile: remove pwd from compile output
* Makefile: add standard 'all' target
* Makefile: evaluate git version lazily
Quality of life improvements for packagers.
* ipc: simplify inflatable buffer and add fuzzer
* fuzz: add generic command argument fuzzer
* fuzz: add set and setconf fuzzers
More fuzzers and a slicker string list implementation. These fuzzers now find
themselves configuring wireguard interfaces from scratch after several million
mutations, which is fun to watch.
* netlink: make sure to clear return value when trying again
Prior, if a dump was interrupted by a concurrent set operation, we'd try
again, but forget to reset an error flag, so we'd keep trying again forever.
Now we do the right thing and succeed when we succeed.
* Makefile: sort inputs to linker so that build is reproducible
Earlier versions of make(1) passed GLOB_NOSORT to glob(3), resulting in the
linker receiving its inputs in a filesystem-dependent order. This screwed up
reproducible builds.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* Makefile: strip prefixed v from version.h
This fixes a mistake in dmesg output and when parsing the sysfs entry in the
filesystem.
* device: skb_list_walk_safe moved upstream
This is a 5.6 change, which we won't support here, but it does make the code
cleaner, so we make this change to keep things in sync.
* curve25519: x86_64: replace with formally verified implementation
This comes from INRIA's HACL*/Vale. It implements the same algorithm and
implementation strategy as the code it replaces, only this code has been
formally verified, sans the base point multiplication, which uses code
similar to prior, only it uses the formally verified field arithmetic
alongside reproducable ladder generation steps. This doesn't have a
pure-bmi2 version, which means haswell no longer benefits, but the
increased (doubled) code complexity is not worth it for a single
generation of chips that's already old.
Performance-wise, this is around 1% slower on older microarchitectures,
and slightly faster on newer microarchitectures, mainly 10nm ones or
backports of 10nm to 14nm. This implementation is "everest" below:
Xeon E5-2680 v4 (Broadwell)
armfazh: 133340 cycles per call
everest: 133436 cycles per call
Xeon Gold 5120 (Sky Lake Server)
armfazh: 112636 cycles per call
everest: 113906 cycles per call
Core i5-6300U (Sky Lake Client)
armfazh: 116810 cycles per call
everest: 117916 cycles per call
Core i7-7600U (Kaby Lake)
armfazh: 119523 cycles per call
everest: 119040 cycles per call
Core i7-8750H (Coffee Lake)
armfazh: 113914 cycles per call
everest: 113650 cycles per call
Core i9-9880H (Coffee Lake Refresh)
armfazh: 112616 cycles per call
everest: 114082 cycles per call
Core i3-8121U (Cannon Lake)
armfazh: 113202 cycles per call
everest: 111382 cycles per call
Core i7-8265U (Whiskey Lake)
armfazh: 127307 cycles per call
everest: 127697 cycles per call
Core i7-8550U (Kaby Lake Refresh)
armfazh: 127522 cycles per call
everest: 127083 cycles per call
Xeon Platinum 8275CL (Cascade Lake)
armfazh: 114380 cycles per call
everest: 114656 cycles per call
Achieving these kind of results with formally verified code is quite
remarkable, especialy considering that performance is favorable for
newer chips.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
hostapd sets minimum values for CWmin/CWmax/AIFS and maximum for TXOP.
The code for applying those values had a few bugs leading to bogus values,
which caused significant latency and packet loss.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Prepare netifd for handling procd service jails having their own
network namespace.
Intefaces having the jail attribute will only be brought up inside the
jail's network namespace by procd calling the newly introduced ubus
method 'netns_updown'.
Currently proto 'static' is supported and configuration changes are
not yet being handled (ie. you'll have to restart the jailed service
for changes to take effect).
Example /etc/config/network snippet:
config device 'veth0'
option type 'veth'
option name 'vhost0'
option peer_name 'virt0'
config interface 'virt'
option type 'bridge'
list ifname 'vhost0'
option proto 'static'
option ipaddr '10.0.0.1'
option netmask '255.255.255.0'
config interface 'virt0'
option ifname 'virt0'
option proto 'static'
option ipaddr '10.0.0.2'
option netmask '255.255.255.0'
option gateway '10.0.0.1'
option dns '10.0.0.1'
option jail 'transmission'
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6db312a dhcpv6-ia: use dhcp leasetime to set preferred/valid statefull lifetimes
2520c48 dhcpv6-ia: introduce DHCPv6 pd and ia assignments flags
b413d8a dhcpv6-ia: cleanup prefix delegation routes
b0902af dhcpv6-ia: remove passing interface as parameter to apply_lease
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Currently, it is very cumbersome for a user to connect to a WPA-Enterprise
based network securely because the RADIUS server's CA certificate must first be
extracted from the EAPOL handshake using tcpdump or other methods before it can
be pinned using the ca_cert(2) fields. To make this process easier and more
secure (combined with changes in openwrt/openwrt#2654), this commit adds
support for validating against the built-in CA bundle when the ca-bundle
package is installed. Related LuCI changes in openwrt/luci#3513.
Signed-off-by: David Lam <david@thedavid.net>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
If a config section of a peer does not have a public key defined, the
whole interface does not start. The following log is shown
daemon.notice netifd: test (21071): Line unrecognized: `PublicKey='
daemon.notice netifd: test (21071): Configuration parsing erro
The command 'wg show' does only show the interface name.
With this change we skip the peer for this interface and emit a log
message. So the other peers get configured.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
With this change it is now possible to switch off single instances of
the uhttpd config. Until now it was only possible to switch all
instances of uhttpd on or off.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Rekey GTK on STA disassociate
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Allows dtim_period to be configurable, the default is from hostapd.
Adds additional regulatory tunables for power constraint and spectrum
managment.
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Failsafe code of dropbear should be in the dropbear package not the
base-files package.
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
The wpa_supplicant supports certificate subject validation via the
subject match(2) and altsubject_match(2) fields. domain_match(2) and
domain_suffix_match(2) fields are also supported for advanced matches.
This validation is especially important when connecting to access
points that use PAP as the Phase 2 authentication type. Without proper
validation, the user's password can be transmitted to a rogue access
point in plaintext without the user's knowledge. Most organizations
already require these attributes to be included to ensure that the
connection from the STA and the AP is secure. Includes LuCI changes via
openwrt/luci#3444.
From the documentation:
subject_match - Constraint for server certificate subject. This substring
is matched against the subject of the authentication server certificate.
If this string is set, the server sertificate is only accepted if it
contains this string in the subject. The subject string is in following
format: /C=US/ST=CA/L=San Francisco/CN=Test AS/emailAddress=as
.example.com
subject_match2 - Constraint for server certificate subject. This field is
like subject_match, but used for phase 2 (inside EAP-TTLS/PEAP/FAST
tunnel) authentication.
altsubject_match - Constraint for server certificate alt. subject.
Semicolon separated string of entries to be matched against the
alternative subject name of the authentication server certificate. If
this string is set, the server sertificate is only accepted if it
contains one of the entries in an alternative subject name extension.
altSubjectName string is in following format: TYPE:VALUE Example:
EMAIL:server@example.com Example:
DNS:server.example.com;DNS:server2.example.com Following types are
supported: EMAIL, DNS, URI
altsubject_match2 - Constraint for server certificate alt. subject. This
field is like altsubject_match, but used for phase 2 (inside
EAP-TTLS/PEAP/FAST tunnel) authentication.
domain_match - Constraint for server domain name. If set, this FQDN is
used as a full match requirement for the
server certificate in SubjectAltName dNSName element(s). If a
matching dNSName is found, this constraint is met. If no dNSName
values are present, this constraint is matched against SubjectName CN
using same full match comparison. This behavior is similar to
domain_suffix_match, but has the requirement of a full match, i.e.,
no subdomains or wildcard matches are allowed. Case-insensitive
comparison is used, so "Example.com" matches "example.com", but would
not match "test.Example.com". More than one match string can be
provided by using semicolons to
separate the strings (e.g., example.org;example.com). When multiple
strings are specified, a match with any one of the values is considered
a sufficient match for the certificate, i.e., the conditions are ORed
together.
domain_match2 - Constraint for server domain name. This field is like
domain_match, but used for phase 2 (inside EAP-TTLS/PEAP/FAST tunnel)
authentication.
domain_suffix_match - Constraint for server domain name. If set, this
FQDN is used as a suffix match requirement for the AAA server
certificate in SubjectAltName dNSName element(s). If a matching dNSName
is found, this constraint is met. If no dNSName values are present,
this constraint is matched against SubjectName CN using same suffix
match comparison. Suffix match here means that the host/domain name is
compared one label at a time starting from the top-level domain and all
the labels in domain_suffix_match shall be included in the certificate.
The certificate may include additional sub-level labels in addition to
the required labels. More than one match string can be provided by using
semicolons to separate the strings (e.g., example.org;example.com).
When multiple strings are specified, a match with any one of the values
is considered a sufficient match for the certificate, i.e., the
conditions are ORed together. For example,
domain_suffix_match=example.com would match test.example.com but would
not match test-example.com. This field is like domain_match, but used
for phase 2 (inside EAP-TTLS/PEAP/FAST tunnel) authentication.
domain_suffix_match2 - Constraint for server domain name. This field is
like domain_suffix_match, but used for phase 2 (inside
EAP-TTLS/PEAP/FAST tunnel) authentication.
Signed-off-by: David Lam <david@thedavid.net>
This activates PIE ASLR support by default when the regular option is
selected.
Size increase on x86/64:
odhcpd-ipv6only Installed-Size: 36821 -> 38216
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This activates PIE ASLR support by default when the regular option is
selected.
This increases the binary size by 39% uncompressed and 21% compressed
on MIPS BE.
old:
33,189 /usr/sbin/uhttpd
23,016 uhttpd_2019-08-17-6b03f960-4_mips_24kc.ipk
new:
46,212 /usr/sbin/uhttpd
27,979 uhttpd_2019-08-17-6b03f960-4_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
This activates PIE ASLR support by default when the regular option is
selected.
This increases the binary size by 26% uncompressed and 16% compressed
on MIPS BE.
old:
460,933 /usr/sbin/wpad
283,891 wpad-basic_2019-08-08-ca8c2bd2-1_mips_24kc.ipk
new:
584,508 /usr/sbin/wpad
330,281 wpad-basic_2019-08-08-ca8c2bd2-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
This activates PIE ASLR support by default when the regular option is
selected.
This increases the binary size by 18% uncompressed and 17% compressed
on MIPS BE.
old:
164,261 /usr/sbin/dropbear
85,648 dropbear_2019.78-2_mips_24kc.ipk
new:
194,492 /usr/sbin/dropbear
100,309 dropbear_2019.78-2_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
This activates PIE ASLR support by default when the regular option is
selected.
This increases the binary size by 37% uncompressed and 18% compressed
on MIPS BE.
old:
146,933 /usr/sbin/dnsmasq
101,837 dnsmasq_2.80-14_mips_24kc.ipk
new:
202,020 /usr/sbin/dnsmasq
120,577 dnsmasq_2.80-14_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
* systemd: update documentation URL
* global: bump copyright
Usual house keeping.
* Makefile: DEBUG_TOOLS -> DEBUG and document
* Makefile: port static analysis check
* dns-hatchet: adjust path for new repo layout
* Makefile: rework automatic version.h mangling
These are some important-ish cleanups for downstream package maintainers that
should make packaging this a lot smoother.
* man: add documentation about removing explicit listen-port
Documentation improvement.
* wg-quick: linux: quote ifname for nft
This should fix issues with weirdly named ifnames and odd versions of nft(8).
* fuzz: find bugs in the config syntax parser
* fuzz: find bugs when parsing uapi input
These are two fuzzers that have been laying around without a repo for a while.
Perhaps somebody with enough compute power will find bugs with them.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* socket: mark skbs as not on list when receiving via gro
Certain drivers will pass gro skbs to udp, at which point the udp driver
simply iterates through them and passes them off to encap_rcv, which is
where we pick up. At the moment, we're not attempting to coalesce these
into bundles, but we also don't want to wind up having cascaded lists of
skbs treated separately. The right behavior here, then, is to just mark
each incoming one as not on a list. This can be seen in practice, for
example, with Qualcomm's rmnet_perf driver. This lead to crashes on
OnePlus devices and possibly other Qualcomm 4.14 devices. But I fear
that it could lead to issues on other drivers on weird OpenWRT routers.
This commit is upstream in net-next as:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=736775d06bac60d7a353e405398b48b2bd8b1e54
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
When running sysupgrade from an existing configuration, UCI option
dhcp.@dnsmasq[0].resolvfile needs to be modified in case it has not
been changed from it's original value.
Accomplish that using a uci-defaults script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Without this commit, ft_psk_generate_local is enabled for non-PSK
networks by default. This breaks 802.11r for EAP networks.
Disable ft_psk_generate_local by default for non-PSK networks resolves
this misbehavior.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Previous commit should have bumped PKG_RELEASE, but git add was
forgotten... Add it now.
Fixes: cd48d8d342 ("dnsmasq: switch to /tmp/resolv.conf.d/resolv.conf.auto")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mount-bind directory instead of resolv.conf.auto file in jail to
avoid problems when the file is deleted/replaced.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a backport from the dnsmasq master which should fix a bug which
could cause a crash in dnsmasq.
I saw the following crashes in my log:
[522413.117215] do_page_fault(): sending SIGSEGV to dnsmasq for invalid read access from 2a001450
[522413.124464] epc = 004197f1 in dnsmasq[400000+23000]
[522413.129459] ra = 004197ef in dnsmasq[400000+23000]
This is happening in blockdata_write() when block->next is
dereferenced, but I am not sure if this is related to this problem or if
this is a different problem. I am unable to reproduce this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add call to fclose for file pointer fp in function t_openpw.
The resource leak could happen during an error handling.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
78cd384 Update README and patchlevel.h for 2.4.8 release
5d03403 pppd: Avoid use of strnlen (and strlen) in vslprintf
a1e950a pppd: Fix IPv6 default route code for Solaris
ca5e61b plugins/rp-pppoe: Make tag parsing loop condition more accurate
c10c3c7 pppd: Make sure word read from options file is null-terminated
b311e98 pppd: Limit memory accessed by string formats with max length specified
3ea9de9 pppd: Eliminate some more compiler warnings
57edb1a pppd: Include time.h header before using time_t
09f695f pppd: Don't free static string
03104ba pppd.h: Add missing headers
388597e pppd: Add defaultroute6 and related options
66ce4ba pppd: Avoid declarations within statements in main.c
5637180 pppd: Fix `ifname` option in case of multilink (#105)
d00f8a0 pppd: Fix variable reference syntax in Makefile.linux
b6b4d28 pppd: Check tdb pointer before closing
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
If CONFIG_DROPBEAR_ZLIB is set, building fails at the packaging stage
due to an undeclared dependency on libz.so.1.
As is already done for the main dropbear package, conditionally add a
dependency on zlib.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
iperf2 is useful for testing UDP over multicast, add an option to permit
the enabling/disabling of multicast support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This reverts commit 10cbc896c0.
The updated iptables package does not build due to the following error
encountered on the buildbots:
cp: cannot stat '.../iptables-1.8.4/ipkg-install/usr/lib/libiptc.so.*': No such file or directory
The changelog mentions "build: remove -Wl,--no-as-needed and libiptc.so" so
it appears as if further packaging changes are needed beyond a simple
version bump.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
As announced on the mailing list, WireGuard will be in Linux 5.6. As a
result, the wg(8) tool, used by OpenWRT in the same manner as ip(8), is
moving to its own wireguard-tools repo. Meanwhile, the out-of-tree
kernel module for kernels 3.10 - 5.5 moved to its own wireguard-linux-
compat repo. Yesterday, releases were cut out of these repos, so this
commit bumps packages to match. Since wg(8) and the compat kernel module
are versioned and released separately, we create a wireguard-tools
Makefile to contain the source for the new tools repo. Later, when
OpenWRT moves permanently to Linux 5.6, we'll drop the original module
package, leaving only the tools. So this commit shuffles the build
definition around a bit but is basically the same idea as before.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
edad0d6 version: bump snapshot
0e38a3c compat: ipv6_dst_lookup_flow was backported to 5.3 and 5.4
2e52c41 wg-quick: linux: use already configured addresses instead of in-memory
3721521 tools: adjust wg.8 syntax for consistency in COMMANDS section
21a1498 wg-quick: linux: try both iptables(8) and nft(8) on teardown
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
iputils has moved from the master tree to the packages feed, and is
switching from the abandoned skbuff.net upstream to
github.com/iputils/iputils.
Ref: https://git.openwrt.org/556698cedf9e86a0ffe9f148d4e8e733676c26f6
Signed-off-by: Petr Štetiar <ynezz@true.cz>
1ec6ece version: bump snapshot
e13de91 main: remove unused include <linux/version.h>
72eb17c wg-quick: linux: support older nft(8)
1d8e978 global: fix up spelling
e02713e wg-quick: linux: add support for nft and prefer it
b4e3a83 compat: support building for RHEL-8.1 instead of RHEL-8.0
f29e3ac socket: convert to ipv6_dst_lookup_flow for 5.5
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Before commit 60fb4c92b6 ("hostapd: add ubus reload") netifd was
tracking hostapd/wpa_supplicant and restarting wifi in case of a
process crash. Restore this behaviour by tracking the PIDs of
hostapd and wpa_supplicant.
Also make sure hostapd and/or wpa_supplicant have been started before
emmitting ubus calls to them using ubus wait_for.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allows graceful restart of crashing hostapd/wpa_supplicant instances
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: attempt to launch only present services]
This enables the CTRL_IFACE_MIB symbol for wpad-full and hostapd-full.
If it is not enabled, statistic outputs such as "hostapd_cli all_sta"
are empty.
Signed-off-by: David Bauer <mail@david-bauer.net>
Update iproute2 to latest stable version, see https://lwn.net/Articles/805654/
for the changes in 5.4.0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* wg-quick: linux: suppress error when finding unused table
This fixes a spurious warning messages seen with recent versions of iproute2
and kernels.
* wg-quick: linux: ensure postdown hooks execute
* wg-quick: linux: have remove_iptables return true
* wg-quick: linux: iptables-* -w is not widely supported
Adding in iptables had some hiccups. For the record, I'm very unhappy about
having to put any firewalling code into wg-quick(8). We'll of course need to
support nftables too at some point if this continues. I'm investigating with
upstream the possibility of adding a sysctl to patch the issue that iptables
is handling now, so hopefully at somepoint down the line we'll be able to shed
this dependency once again.
* send: use kfree_skb_list
* device: prepare skb_list_walk_safe for upstreaming
* send: avoid touching skb->{next,prev} directly
Suggestions from LKML.
* ipc: make sure userspace communication frees wgdevice
Free things properly on error paths.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
IPv6 protocol is enabled on all gre interfaces, but gre(v6)tap
interfaces are usually added to a bridge interface, in which case
IPv6 should be enabled only on the bridge interface.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
* messages: recalculate rekey max based on a one minute flood
* allowedips: safely dereference rcu roots
* socket: remove redundant check of new4
* allowedips: avoid double lock in selftest error case
* tools: add syncconf command
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
dnsmasq v2.80 made 'dnssec-check-unsigned' the default, thus the uci
option was rendered ineffectual: we checked unsigned zones no matter the
setting.
Disabling the checking of unsigned zones is now achieve with the
"--dnssec-check-unsigned=no" dnsmasq option.
Update init script to pass required option in the disabled case.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
8174814 utils: persist effective extra_src and extra_dest options in state file
72a486f zones: fix emitting match rules for zones with only "extra" options
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Change dhcp no/release on shutdown to 'norelease' uci option to match
existing proto dhcpv6 usage.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Add ubus interface to hostapd and wpa_supplicant to allow dynamically
reloading wiface configuration without having to restart the hostapd
process.
As a consequence, both hostapd and wpa_supplicant are now started
persistently on boot for each wifi device in the system and then
receive ubus calls adding, modifying or removing interface
configuration.
At a later stage it would be desirable to reduce the services to one
single instance managing all radios.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7a723d0 wireless: add ubus method for reloading configuration
e15147c wireless: make reconf opt-in and allow serializing configuration
Set new option 'reconf' in 'wifi-device' section to enable dynamic
re-configuration on that radio.
If necessary, also set option 'serialize' which forced netifd to
configure interfaces of wireless devices one-by-one.
Both options are disabled by default.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This decreases the size of the swconfig application by 25% on MIPS BE.
old:
16,916 /sbin/swconfig
new:
12,565 /sbin/swconfig
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This decreases the binary size when PIE ASLR is activated by 8% on MIPS BE.
old:
202,020 /usr/sbin/dnsmasq
new:
185,676 /usr/sbin/dnsmasq
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This enables PMKSA and opportunistic key caching by default for
WPA2/WPA3-Personal, WPA3-Personal and OWE auth types.
Otherwise, Apple devices won't connect to the WPA3 network.
This should not degrade security, as there's no external authentication
provider.
Tested with OCEDO Koala and iPhone 7 (iOS 13.1).
Signed-off-by: David Bauer <mail@david-bauer.net>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Enables radio resource management to be reported by hostapd to clients.
Ref: https://github.com/lede-project/source/pull/1430
Co-developed-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
When ASLR_PIE was activated globally these drivers failed to build
because the user space LDFLAGS leaked into the kernel build process.
This was fixed in upstream Linux kernel commit ce99d0bf312d ("kbuild:
clear LDFLAGS in the top Makefile") which went into Linux 4.17. The
lantiq target is now on Linux 4.19 only and these exceptions are not
needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Required as dependency on dropbear config headers is not tracked in
dropbear build system
Fixes FS#2275
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This updates mac80211 to backports based on kernel 5.4-rc2
ath10k-ct was updated to match the API changes and iw now uses the new
nl80211.h header file.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If system has more then one and different wwan interface (modem). Then the
wwan protohandler will always take the modem which is discovered first.
The protohandler will always setup the same interface. To fix this add a
new usb "bus" option which is associated with wwan device and so will set
the specified interface up. With this change more then one interface
could be mananged by the wwan protohandler.
If the "bus" option is not set in the uci network config then the protohandler
behaves as before the change. The protohanldler will take the first
interface which he founds.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This is a precursor to adding proper support for multiple
6in4 tunnels with the already programmed tunlink parameter.
This is an essential sanity check so as to not break existing
and working behind NAT setups.
Signed-off-by: Sean Kenny <skenny@wfap.ca>
6in4: add myip he.net api parameter logic
This is to add proper support for multiple 6in4 tunnels
with the already programmed tunlink parameter.
As it stands before this commit, if there is a multi wan setup that
consists of dynamic ips, there is no way to use the
dynamic update feature as the he.net api is implicitly using
the ip address of the caller. This will explicitly use the
ipaddr specified in the interface config OR the ip of the
tunlink interface specified in the dynamic update api call instead
ONLY if the final resolved ipaddr variable is not an rfc1918 address.
Signed-off-by: Sean Kenny <skenny@wfap.ca>
8eb8443 version: bump snapshot
be09cf5 wg-quick: android: use Binder for setting DNS on Android 10
4716f85 noise: recompare stamps after taking write lock
54db197 netlink: allow preventing creation of new peers when updating
f1b87d1 netns: add test for failing 5.3 FIB changes
a3539c4 qemu: bump default version
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Commit 7519a36774 ("base-files,procd: add generic service status")
introduced the generic 'status' command which broke the previous
dsl_control status output. To fix this, let's rename the "old" command
to "dslstat".
Fixes: 7519a36774 ("base-files,procd: add generic service status")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
0d004db Revert "pppd: Include time.h before using time_t"
e400854 pppdump: Eliminate printf format warning by using %zd
7f2f0de pppd: Refactor setjmp/longjmp with pipe pair in event wait loop
4e71317 make: Avoid using host include for cross-compiling
3202f89 pppoe: Remove the use of cdefs
d8e8d7a pppd: Remove unused rcsid variables
486f854 pppd: Fix GLIBC version test for non-glibc toolchains
b6cd558 pppd: Include time.h before using time_t
ef8ec11 radius: Fix compiler warning
f6330ec magic: Remove K&R style of arguments
347904e Add Submitting-patches.md
Remove patches 130-no_cdefs_h.patch, 131-missing_prototype_macro.patch,
132-fix_linux_includes.patch as fixed upstream
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Wifi HE (ieee80211ax) parsing is currently only activated in the full
version because it increases the compressed size by 2.5KBytes.
This also activates link time optimization (LTO) again, the problem was
fixed upstream
This increases the uncompressed binary size of iw-tiny by about 1.7%
old:
34446 iw_5.0.1-1_mipsel_24kc.ipk
new:
35064 iw_5.3-1_mipsel_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
