Commit Graph

1568 Commits

Author SHA1 Message Date
Rui Salvaterra
3f567d8452 tools/sstrip: update to latest version
Drop our local sstrip copy and use the current ELFKickers upstream
version.

Patch the original makefile in order to avoid building elftoc, since it
fails with musl's elf.h. This is fine, since we only need sstrip anyway.

Finally, add the possibility to pass additional arguments to sstrip and
pass -z (remove trailing zeros) by default, which matches the behaviour
of the previous version.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[shorten long commit msg lines]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-26 12:44:25 -10:00
Tomasz Maciej Nowak
bc64b9c32e treewide: update email address of Tomasz Maciej Nowak
Replace my o2.pl email address.

I'm still available at the old address.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-24 15:39:07 +01:00
Sander Vanheule
b0ecae504b ath79: support for TP-Link EAP225 v3
TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access
point. Serial port access for debricking requires fine soldering.

Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE

Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface

Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
      Do NOT bridge R230.
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM boot log:

    Using interface ath0 with hwaddr b0:...:3e and ssid "..."
    Using interface ath10 with hwaddr b0:...:3f and ssid "..."

Tested by forum user blinkstar88

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-11-23 22:53:15 +01:00
Sander Vanheule
4f86edf477 ath79: support for TP-Link EAP225-Outdoor v1
TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall
mount access point. Debricking requires access to the serial port, which
is non-trivial.

Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (AR8033): 1× 1GbE, PoE

Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface

Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
  * Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:

    ath0      Link encap:Ethernet  HWaddr D8:...:2E
    ath10     Link encap:Ethernet  HWaddr D8:...:2F
    br0       Link encap:Ethernet  HWaddr D8:...:2E
    eth0      Link encap:Ethernet  HWaddr D8:...:2E

Tested by forum user PolynomialDivision on firmware v1.7.0.
UART access tested by forum user arinc9.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-11-23 22:53:15 +01:00
Sander Vanheule
b11ad48764 ath79: support for TP-Link EAP245 v1
TP-Link EAP245 v1 is an AC1750 (802.11ac Wave-1) ceiling mount access point.

Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9880): a/n/ac, 3x3
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE

Flashing instructions:
* Upgrade the device to firmware v1.4.0 if necessary
* Exploit the user management page in the web interface to start telnetd
  by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
  (e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
  patch listed below. The patch is required to prevent `uclited -u` in
  the last step from crashing.
* Copy the patched uclited programme back to the device at /tmp/uclited
  (via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.

    --- xxd uclited
    +++ xxd uclited-patched
    @@ -53796,7 +53796,7 @@
     000d2240: 8c44 0000 0320 f809 0000 0000 8fbc 0010  .D... ..........
     000d2250: 8fa6 0a4c 02c0 2821 8f82 87b8 0000 0000  ...L..(!........
    -000d2260: 8c44 0000 0c13 45e0 27a7 0018 8fbc 0010  .D....E.'.......
    +000d2260: 8c44 0000 2402 0000 0000 0000 8fbc 0010  .D..$...........
     000d2270: 1040 001d 0000 1821 8f99 8374 3c04 0058  .@.....!...t<..X
     000d2280: 3c05 0056 2484 a898 24a5 9a30 0320 f809  <..V$...$..0. ..

Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
      Do NOT bridge R230.
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

Tested on the EAP245 v1 running the latest firmware (v1.4.0). The binary
patch might not apply to uclited from other firmware versions.

EAP245 v1 device support was originally developed and maintained by
Julien Dusser out-of-tree. This patch and "ath79: prepare for 1-port
TP-Link EAP2x5 devices" are based on that work.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-11-23 22:53:15 +01:00
Hannu Nyman
39fa0c0959 tools/mpc: update to 1.2.1
Update mpc to 1.2.1

http://www.multiprecision.org/mpc/
  Bug fixes:
    Fix an incompatibility problem with GMP 6.0 and before.
    Fix an intermediate overflow in asin.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-11-21 18:49:27 +01:00
Hannu Nyman
c977bd033e tools/gmp: update to 6.2.1
Update gmp to 6.2.1

Release notes: https://gmplib.org/gmp6.2

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-11-21 18:49:17 +01:00
Hannu Nyman
9d5eceae91 tools/bison: update to 3.7.4
Update bison to 3.7.4

Release notes:
http://git.savannah.gnu.org/cgit/bison.git/tree/NEWS?id=7a11a9308cb

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-11-21 18:49:08 +01:00
Hannu Nyman
7d03e90390 tools/cmake: update to 3.18.5
Update cmake to 3.18.5

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-11-21 18:48:59 +01:00
Hannu Nyman
a233e3a9af tools/expat: update to 2.2.10
Update expat to 2.2.10

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-11-21 18:48:39 +01:00
Felix Fietkau
6c2ef55e69 tools/bc: use autoreconf to fix build failure on macOS with recent Xcode versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-11-14 14:48:30 +01:00
Felix Fietkau
a99f88a186 tools/libelf: use autoreconf to fix build failure on macOS with recent Xcode versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-11-14 14:48:30 +01:00
Felix Fietkau
0fd214d89f tools/fakeroot: fix build on macOS with recent Xcode versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-11-14 14:48:30 +01:00
INAGAKI Hiroshi
65f3e7ce1f firmware-utils: fix mistake and improve logic in nec-enc
this patch fixes/improves follows:

- PATTERN_LEN is defined as a macro but unused
- redundant logic in count-up for "ptn"

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-11-12 18:19:44 +01:00
Jo-Philipp Wich
d4521fb132 tools: fakeroot: rework relocatable patch to avoid LD_LIBRARY_PATH usage
Due to the use of LD_LIBRARY_PATH, the programs running in the fakeroot
environment may end up loading bundled SDK libraries using the system
ld.so.

Rework the relocatability patch to avoid meddling with LD_LIBRARY_PATH
and construct the paths to faked and libfakeroot.so directly.

Fixes: f93cb5c2c8 ("fakeroot: make fakeroot script relocatable")
Reviewed-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-11-10 08:31:10 +01:00
Jo-Philipp Wich
f93cb5c2c8 fakeroot: make fakeroot script relocatable
Patch the fakeroot script template to discover faked and libfakeroot.so
relative to the STAGING_DIR_HOST environment variable, similar to how it
is done for automake, libtool, quilt and autoconf already.

This avoids the need for passing the paths to faked and libfakeroot.so
manually every time we invoke fakeroot and subsequently allows us to
drop OS X specific logic.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-10-30 00:39:09 +00:00
Richard Fröhning
33b76d66d1 ramips: add support for TP-Link RE200 v4
TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas.
It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

The MAC address assignment matches stock firmware, i.e.:

LAN : *:8E
2.4G: *:8D
5G  : *:8C

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

Instructions for serial console and recovery may be checked out in
commit 6d6f36ae78 ("ramips: add support for TP-Link RE200 v2") or on
the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[removed empty line, fix commit message formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-10-20 03:01:13 +02:00
Adrian Schmutzler
e3af1666f4 ath79: rename TP-Link TL-WPA8630P v2 (EU) to v2.0 (EU)
Since we have a v2.1 (EU) with different partitioning now, rename
the v2.0 to make the difference visible to the user more directly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-04 15:44:05 +02:00
Joe Mullally
7422c7a6fa ath79: add support for TP-Link TL-WPA8630P (EU) v2.1
This adds support for the TP-Link TL-WPA8630P (EU) in its v2.1
version. The only unique aspect for the firmware compared to v2
layout is the partition layout.

Note that while the EU version has different partitioning for
v2.0 and v2.1, the v2.1 (AU) is supported by the v2-int image.

If you plan to use this device, make sure you have a look at
the Wiki page to check whether the device is supported and
which image needs to be taken.

Specifications
--------------

  - QCA9563 750MHz, 2.4GHz WiFi
  - QCA9888 5GHz WiFi
  - 8MiB SPI Flash
  - 128MiB RAM
  - 3 GBit Ports (QCA8337)
  - PLC (QCA7550)

Installation
------------

Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.

Notes
-----

The OEM firmware has 0x620000 to 0x680000 unassigned, so we leave
this empty as well. It is complicated enough already ...

Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[improve partitions, use v2 DTSI, add entry in 02_network, rewrite
and extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-04 15:44:05 +02:00
Yuan Tao
649e098ec0 tools/libressl: update to 3.2.1
libressl update to 3.2.1
Delete 001-dont-build-tests-man.patch
Add configure args :
--enable-static
--disable-tests

The patch (001-dont-build-tests-man.patch) no longer works with the current version.
Follow the patch notes:
Adding the --enable-static and --disable-tests parameters should replace the patch.

Signed-off-by: Yuan Tao <ty@wevs.org>
2020-09-18 20:08:51 +02:00
Adrian Schmutzler
0b1cdb7eea treewide: remove empty default cases
There is no apparent reason to have an empty default case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 12:46:19 +02:00
Sander Vanheule
c9f51a9ad6 ath79: support for TP-Link EAP225-Wall v2
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.

The device was kindly provided for porting by Stijn Segers.

Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
  * Eth0 (back): 802.3af/at PoE in
  * Eth1, Eth2 (bottom)
  * Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
  * LED button, implemented as KEY_BRIGHTNESS_TOGGLE
  * Reset button

Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface

Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
      Do NOT bridge R164
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
    br0       Link encap:Ethernet  HWaddr 50:...:04
    eth0      Link encap:Ethernet  HWaddr 50:...:04
    wifi0     Link encap:UNSPEC  HWaddr 50-...-04-...
    wifi1     Link encap:UNSPEC  HWaddr 50-...-05-...

Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 19:37:24 +02:00
Sander Vanheule
9dd4ba3d7e ath79: add support for TP-Link EAP245-v3
TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.

Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)

Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface

The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.

Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.

Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt

Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
    ath0      Link encap:Ethernet  HWaddr 74:..:E2
    ath10     Link encap:Ethernet  HWaddr 74:..:E3
    br0       Link encap:Ethernet  HWaddr 74:..:E2
    eth0      Link encap:Ethernet  HWaddr 74:..:E2

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-09-09 20:42:10 +03:00
Sander Vanheule
14464e1128 firmware-utils/tplink-safeloader: add compat level
TP-Link has introduced a compatibility level to prevent certain
downgrades. This information is stored in the soft-version partition,
changing the data length from 0xc to 0x10.

The compatibility level doesn't change frequently. For example, it has
the following values for the EAP245v3 (released 2018-Q4):
* FW v2.2.0  (2019-05-30): compat_level=0
* FW v2.3.0  (2019-07-31): compat_level=0
* FW v2.3.1  (2019-10-29): compat_level=1
* FW v2.20.0 (2020-04-23): compat_level=1

Empty flash values (0xffffffff) are interpreted as compat_level=0.
If a firmware upgrade file has a soft-version block without
compatibility level (data length < 0x10), this is also interpreted as
compat_level=0.

By including a high enough compatibility level in factory images, stock
firmware can be convinced to accept the image. A compatibility level
aware firmware will keep the original value.

Example upgrade log of TP-Link EAP245v3 FWv2.3.0 to FWv2.20.0:
    [NM_Debug](nm_fwup_verifyFwupFile) 02073: curSoftVer:2.3.0 Build
        20190731 Rel. 51932,newSoftVer:2.20.0 Build 20200423 Rel. 36779
    ...
    AddiHardwareVer check: NEW(0x1) >= CUR(0x0), Success.
    ...
    [NM_NOTICE](updateDataToNvram) 00575: Restore old additionalHardVer:
    0x0.(new 0x1)
    [NM_NOTICE](updateDataToNvram) 00607: PTN 07: name = soft-version,
        base = 0x00092000, size = 0x00000100 Bytes, upDataType = 1,
        upDataStart = 7690604b, upDataLen = 00000018
    [NM_Debug](updateDataToNvram) 00738: PTN 07: write bytes = 000002eb

Other firmware upgrades have been observed to modify the compabitility
stored level (e.g. TP-Link EAP225-Outdoor FWv1.4.1 to FWv1.7.0).
Therefore, it seems to be the safest option to set the OpenWrt
compatibility level to the highest known value instead of the highest
possible value (0xfffffffe), to ensure users do not get unexpectedly
refused firmware upgrades when using a device reverted back to stock.

To remain compatible with existing devices and not produce different
images, the image builder doesn't store a compatibility level if it is
zero.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-09-09 20:41:50 +03:00
Sander Vanheule
6985a26e59 firmware-utils/tplink-safeloader: soft-version magic is data length
The soft-version partition actually contains a header and trailing data:
* header: {data length, [zero]}
* data: {version, bcd encoded date, revision}

The data length is currently treated as a magic number, but should
contain the length of the partition data.

This header is also present the following partitions (non-exhaustive):
* string-based soft-version
* support-list

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-09-09 20:41:50 +03:00
Jo-Philipp Wich
6485f521c9 tools: fakeroot: use TCP as IPC transport
Some environments, e.g. first gen WSL, do not support SysV IPC.
Enforce the use of TCP transport instead which should be universally
available.

Fixes: FS#3317
Ref: https://github.com/microsoft/WSL/issues/4067
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-09-09 13:33:50 +02:00
Daniel Golle
97096531bb fakeroot: add license information
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-09-08 15:02:52 +01:00
Adrian Schmutzler
94198e2a1c rb532: drop target
This target is still on kernel 4.14, and recent attempts to move it to
kernel 5.4 have not led to success. The device tester reported that it
wouldn't boot with the following messages:

From sysupgrade:

  Press any key within 4 seconds to enter setup....
  loading kernel from nand... OK
  setting up elf image... OK
  jumping to kernel code

At this point the system hangs.

From CompactFlash:

  Press any key within 4 seconds to enter setup....
  Booting CF
  Loading kernel... done
  setting up elf image... kernel out of range kernel loading failed

The tester reported that the same was observed with current master
(kernel 4.14) as well. This looks like some kernel size restriction.

Since this target is quite old and only supports one device, and since
nobody else seemed interested in working on this for quite some time,
I decided to not put further work into analyzing the problem and drop
this together with the other 4.14-only targets.

Patchwork series:
https://patchwork.ozlabs.org/project/openwrt/list/?series=197066&state=*

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Adrian Schmutzler
edb5d2a320 tools: sort alphabetically
This sorts the added tools and builddir dependencies alphabetically
to make it easier to find something in the Makefile.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Adrian Schmutzler
48905af01d tools: drop unused upslug2 and wrt350nv2-builder
These tools have been used by the orion target which has been
removed in Jan 2020 [1].

Both were specifically meant for the WRT350Nv2, which is not
supported anymore.

So, let's remove them as well.

[1] 89f2deb372 ("orion: remove unmaintained target")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Felix Fietkau
7f0cb91d71 tools/squashfskit4: fix build on non-linux systems
The xattr related function calls are linux specific

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-01 17:01:56 +02:00
Paul Spooren
35f2116519 treewide: https for downloads.openwrt.org sources
Instead of using http and https for source downloads from
downloads.openwrt.org, always use https for it's better security.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-31 11:26:10 +01:00
Thomas Petazzoni
d3d40cd6a4 tools/squashfskit4: add xattr support to mksquashfs for SELinux
SELinux uses extended attributes to store SELinux security contexts.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase, add commit message]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
2020-08-31 01:15:41 +01:00
David Bauer
1aa71833fe tools: add back lzma-old for ath79
lzma-old host package is required for building ath79 images, as
mksquashfs-lzma is required for generating netgear images.

Fixes commit 4e4ee46495 ("ar71xx: drop target")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-08-31 00:21:18 +02:00
Hannu Nyman
040b625c4b tools/coreutils: update to 8.32
Update coreutils to version 8.32.
Remove upstreamed patch.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-30 22:21:34 +02:00
Adrian Schmutzler
d7fb7ac278 ath79: increase kernel partition for ar9344 TP-Link CPE/WBS
The kernel has become too big again for the ar9344-based TP-Link
CPE/WBS devices which still have no firmware-partition splitter.

Current buildbots produce a kernel size of about 2469 kiB, while
the partition is only 2048 kiB (0x200000). Therefore, increase it
to 0x300000 to provide enough room for this and, hopefully, the
next kernel.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 22:20:37 +02:00
Adrian Schmutzler
4e4ee46495 ar71xx: drop target
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.

This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 22:18:35 +02:00
Hannu Nyman
395c848d16 tools/mpc: update to 1.2.0
Update mpc to version 1.2.0.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-27 21:18:16 +02:00
Hauke Mehrtens
561031921f tools: mtd-utils: Update to version 2.1.2
The release notes says this:
As already said, the changes since 2.1.1 are primarily bug fixes, addressing
compiler warnings and issues reported by diagnostic tools, but also build
failures for some configurations.
https://lists.infradead.org/pipermail/linux-mtd/2020-July/081299.html

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-26 23:29:35 +02:00
Hannu Nyman
d622cf81af tools/ccache: update to 3.7.11
Update ccache to 3.7.11

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-23 19:40:51 +02:00
Hannu Nyman
84834df9b9 tools/cmake: update to 3.18.2
Update cmake to version 3.18.2.
Refresh patches.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-23 19:40:42 +02:00
Hannu Nyman
4faf7704a2 tools/mpfr: update to 4.1.0
Update mpfr to version 4.1.0.
Refresh patches.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-23 19:40:32 +02:00
Hannu Nyman
1cf842dd13 tools/bison: update to 3.7.1
Update GNU bison to version 3.7.1.
Refresh patches.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-23 11:29:24 +02:00
Alexander Couzens
6d5d815e3f
tools/tplink-safeloader: use soft_ver 1.9.1 for archer c6 v2
TP-LINK published a firmware update for the archer c6 v2.
This updates also reached the factory devices. Newer software version
rejects downgrading to 1.2.x. Use 1.9.x to allow installing the factory images
and have a little bit time to change it again.

Tested on archer c6 v2 with firmware 1.3.1

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-08-19 19:21:24 +02:00
Felix Fietkau
a36965347e tools/coreutils: install ln
It is needed for libsepol on non-GNU systems

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-13 20:08:29 +02:00
Andreas Böhler
ab74def0db ath79: add support for TP-Link TL-WPA8630P v2
The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC
and 2.4GHz and 5GHz WiFi modules.

Specifications
--------------

  - QCA9563 750MHz, 2.4GHz WiFi
  - QCA9888 5GHz WiFi
  - 8MiB SPI Flash
  - 128MiB RAM
  - 3 GBit Ports (QCA8337)
  - PLC (QCA7550)

MAC address assignment
----------------------

WiFi 2.4GHz and LAN share the same MAC address as printed on the label.
5GHz WiFi uses LAN-1, based on assumptions from similar devices.

LAN Port assignment
-------------------

While there are 3 physical LAN ports on the device, there will be 4
visible ports in OpenWrt. The fourth port (internal port 5) is used
by the PowerLine Communication SoC and thus treated like a regular
LAN port.

Versions
--------

Note that both TL-WPA8630 and TL-WPA8630P, as well as the different
country-versions, differ in partitioning, and therefore shouldn't be
cross-flashed.

This adds support for the two known partitioning variants of the
TL-WPA8630P, where the variants can be safely distinguished via the
tplink-safeloader SupportList. For the non-P variants (TL-WPA8630),
at least two additional partitioning schemes exist, and the same
SupportList entry can have different partitioning.
Thus, we don't support those officially (yet).

Also note that the P version for Germany (DE) requires the international
image version, but is properly protected by SupportList.

In any case, please check the OpenWrt Wiki pages for the device
before flashing anything!

Installation
------------

Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.

Additional thanks to Jon Davies and Joe Mullally for bringing
order into the partitioning mess.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[minor DTS adjustments, add label-mac-device, drop chosen, move
common partitions to DTSI, rename de to int, add AU support strings,
adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk,
adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 11:48:08 +02:00
Thomas Petazzoni
9e7ef46065 tools: add fakeroot
SELinux support requires setting the appropriate SELinux security context
to files and directories, which needs to happen at build time in order
to support read-only root filesystem scenarios. In order to create these
security contexts, we will have to run some SELinux-specific tools on
the host machine, but that requires root access. This adds support for
fakeroot, which the build process will use to run the SELinux security
context creation and the image creation.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>

Apply to current master, and adjust commit message

Thomas' original work is available at
http://lists.infradead.org/pipermail/openwrt-devel/2019-November/025976.html.

Signed-off-by: W. Michael Petullo <mike@flyn.org>
[add rules.mk FAKEROOT variable]
Signed-off-by: Paul Spooren <mail@aparcar.org>
[update, fix macos build]
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-10 10:09:55 +02:00
Piotr Stefaniak
e27fbae63c tools/cmake: fix typo in parallel make patch
The variable in the case argument was mistyped, so the case always
checked against an empty string and never matched.

Fix the variable name. Add a PKG_RELEASE to Makefile so we can bump it.

Fixes: d6de31310c ("cmake: restore parallel build support for bootstrap")

Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
[add commit message, add PKG_RELEASE, fix commit title, add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 00:01:51 +02:00
Adrian Schmutzler
c25c9e98f5 Revert "build: fix typo in cmake patch"
This reverts commit 685570858d.

The commit had several formal flaws, revert it and hopefully apply
it properly next time.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-09 23:59:20 +02:00
Piotr Stefaniak
685570858d build: fix typo in cmake patch
The variable in the case argument was mistyped, so the case always
checked against an empty string and never matched.

Fix the variable name.

Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
[add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-09 23:57:17 +02:00