a9071d02b5
The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
61 lines
1.3 KiB
Bash
61 lines
1.3 KiB
Bash
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2016 LEDE
|
|
#
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
ubootenv_mtdinfo () {
|
|
UBOOTENV_PART=$(cat /proc/mtd | grep APPSBLENV)
|
|
mtd_dev=$(echo $UBOOTENV_PART | awk '{print $1}' | sed 's/:$//')
|
|
mtd_size=$(echo $UBOOTENV_PART | awk '{print "0x"$2}')
|
|
mtd_erase=$(echo $UBOOTENV_PART | awk '{print "0x"$3}')
|
|
nor_flash=$(find /sys/bus/spi/devices/*/mtd -name ${mtd_dev})
|
|
|
|
if [ -n "$nor_flash" ]; then
|
|
ubootenv_size=$mtd_size
|
|
else
|
|
# size is fixed to 0x40000 in u-boot
|
|
ubootenv_size=0x40000
|
|
fi
|
|
|
|
sectors=$(( $ubootenv_size / $mtd_erase ))
|
|
echo /dev/$mtd_dev 0x0 $ubootenv_size $mtd_erase $sectors
|
|
}
|
|
|
|
case "$board" in
|
|
alfa-network,ap120c-ac |\
|
|
edgecore,ecw5211 |\
|
|
glinet,gl-b1300 |\
|
|
luma,wrtq-329acn |\
|
|
openmesh,a42 |\
|
|
openmesh,a62)
|
|
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
buffalo,wtr-m2133hp)
|
|
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
linksys,ea6350v3)
|
|
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x20000" "0x20000"
|
|
;;
|
|
linksys,ea8300 |\
|
|
linksys,mr8300)
|
|
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
zyxel,nbg6617)
|
|
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config ubootenv
|
|
|
|
exit 0
|