tn3399_openwrt/target/linux/ath79/dts/qca9531_qxwlan_e600gac-v2-16m.dts

49 lines
816 B
Plaintext
Raw Normal View History

ath79: add support for Qxwlan E600G v2 / E600GAC v2 E600G v2 based on Qualcomm/Atheros QCA9531 Specification: - 650/600/200 MHz (CPU/DDR/AHB) - 128/64 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz - 2 x 10/100 Mbps Ethernet(RJ45) - 1 x MiniPCI-e - 1 x SIM (3G/4G) - 5 x LED , 1 x Button(SW2-Reset Buttun), 1 x power input - UART(J100) header on PCB(115200 8N1) E600GAC v2 based on Qualcomm/Atheros QCA9531 + QCA9887 Specification: - 650/600/200 MHz (CPU/DDR/AHB) - 128/64 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz - 1T1R 5 GHz - 2 x 10/100 Mbps Ethernet(RJ45) - 6 x LED (one three-color led), 2 x Button(SW2-Reset Buttun),1 x power input - UART (J100)header on PCB(115200 8N1) Flash instruction: 1.Using tftp mode with UART connection and original OpenWrt image - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "openwrt-ath79-generic-xxx-squashfs-sysupgrade.bin" to "firmware.bin" and place it in tftp server directory. - Connect PC with one of LAN ports, power up the router and press key "Enter" to access U-Boot CLI. - Use the following commands to update the device to OpenWrt: run lfw - After that the device will reboot and boot to OpenWrt. - Wait until all LEDs stops flashing and use the router. 2.Using httpd mode with Web UI connection and original OpenWrt image - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server. - Connect PC with one of LAN ports,press the reset button, power up the router and keep button pressed for around 6-7 seconds, until leds flashing. - Open your browser and enter 192.168.1.1,You will see the upgrade interface, select "openwrt-ath79-generic-xxx-squashfs- sysupgrade.bin" and click the upgrade button. - After that the device will reboot and boot to OpenWrt. - Wait until all LEDs stops flashing and use the router. Signed-off-by: 张鹏 <sd20@qxwlan.com> [rearrange in generic.mk, fix one case in 04_led_migration, update commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-31 01:35:21 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qca9531_qxwlan_e600g.dtsi"
/ {
model = "Qxwlan E600GAC v2 16M";
compatible = "qxwlan,e600gac-v2-16m", "qca,qca9531";
};
&keys {
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
&leds {
wlan2g {
label = "orange:wlan2g";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
control1 {
label = "green:control";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
control2 {
label = "red:control";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
control3 {
label = "blue:control";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
};
&partitions {
partition@70000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x070000 0xf90000>;
};
};