Commit Graph

53395 Commits

Author SHA1 Message Date
Sander Vanheule
004d4d66c8 realtek: fix node addresses for RTL839x
The address in some node names doesn't match the actual offset specified
in the DT node. Update the names to fix this.

While fixing the node names, also drop the unused node labels.

Fixes: 0a7565e536 ("realtek: Update rtl839x.dtsi for realtek,rtl-intc, new gpio controller remove RTL8231 node")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:55 +00:00
Sander Vanheule
1ca081000a realtek: consolidate bootargs again
Bootargs for devices in the realtek target were previously consolidated
in commit af2cfbda2b ("realtek: Consolidate bootargs"), since all
devices currently use the same arguments.

Commit a75b9e3ecb ("realtek: Adding RTL930X sub-target") reverted this
without any argumentation, so let's undo that.

Commit 0b8dfe0851 ("realtek: Add RTL931X sub-target") introduced the
old bootargs also for RTL931x, without providing any actual device
support. Until that is done, let's assume vendors will have done what
they did before, and use a baud rate of 115200.

Fixes: a75b9e3ecb ("realtek: Adding RTL930X sub-target")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:55 +00:00
Matthew Hagan
6f88526fa4 mvebu: cortexa72: enable ARM_ARMADA_8K_CPUFREQ
Enable the AP806's cpufreq driver. This driver is compatible with the
Armada 7K and 8K platforms.

Tested-by: Stijn Segers <foss@volatilesystems.org> (RB5009UG+S+IN)
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2022-02-20 14:26:43 +01:00
Josef Schlehofer
696f0a1cb4 uboot-mvebu: backport pending patches for Marvell A38x
100-ddr-marvell-a38x-fix-BYTE_HOMOGENEOUS_SPLIT_OUT-deci.patch [1]:
SoC Marvell A38x is used in Turris Omnia, and we thought that with recent
fiddling around DDR training to fix it once for all, there were
reproduced the issue in the upcoming new revision Turris Omnia boards.

101-arm-mvebu-spl-Add-option-to-reset-the-board-on-DDR-t.patch [2]:
This is useful when some board may occasionally fail with DDR training,
and it adds the option to reset the board on the DDR training failure

102-arm-mvebu-turris_omnia-Reset-the-board-immediately-o.patch [3]:
This enables the option CONFIG_DDR_RESET_ON_TRAINING_FAILURE (added by
101 patch), so the Turris Omnia board is restarted immediately, and it
does not require to reset the board manually or wait 120s for MCU to
reset the board

[1] https://patchwork.ozlabs.org/project/uboot/patch/20220217000837.13003-1-kabel@kernel.org/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-1-kabel@kernel.org/
[3] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-2-kabel@kernel.org/

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-02-20 14:26:42 +01:00
John Audia
82da1dfd69 bcm27xx: bcm2711: update defconfig
Enabled CONFIG_ALL_KMODS and ran make kernel_menuconfig against
bcm2711 to update defconfig.  Some of the removed symbols are
present in target/linux/generic/config-5.10 while others were
removed by the make target.

Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (wrapped)
2022-02-20 14:26:42 +01:00
John Audia
a478202d74 bcm27xx: bcm2710: update defconfig
Enabled CONFIG_ALL_KMODS and ran make kernel_menuconfig against
bcm2710 to update defconfig.  Some of the removed symbols are
present in target/linux/generic/config-5.10 while others were
removed by the make target.

Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (wrapped)
2022-02-20 14:26:42 +01:00
John Audia
332f69583a bcm27xx: bcm2709: update defconfig
Enabled CONFIG_ALL_KMODS and ran make kernel_menuconfig against
bcm2709 to update defconfig.  Some of the removed symbols are
present in target/linux/generic/config-5.10 while others were
removed by the make target.

Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (wrapped)
2022-02-20 14:26:41 +01:00
John Audia
dbb45421ba bcm27xx: bcm2708: update defconfig
Enabled CONFIG_ALL_KMODS and ran make kernel_menuconfig against
bcm2708 to update defconfig.  Some of the removed symbols are
present in target/linux/generic/config-5.10 while others were
removed by the make target.

Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (wrapped)
2022-02-20 14:26:41 +01:00
Florian Eckert
808210d992 mac80211: add debug compile option for rtw88 devices
This commit adds the following package compile options.

CONFIG_PACKAGE_RTW88_DEBGUG:
Compile the driver with additional debug logging output

CONFIG_PACKAGE_RTW88_DEBGUGFS:
Add the possibility to map information about the driver rtw88 into
debugfs.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-02-20 14:26:40 +01:00
Robert Marko
c1e06a0cbb ipq40xx: mikrotik: fix LED script
Fix the missing ;; after the cAP ac case in /e/b/01_leds.

Fixes: 93d9119 ("ipq40xx: add MikroTik cAP ac support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (minor touch-up)
2022-02-20 14:24:43 +01:00
Lech Perczak
411940ded4 ath79: uboot-envtools: fix partition for ZTE MF286
By mistake, a wrong partition for U-boot environment was introduced for
ZTE MF286 while adding support, when flash layout wasn't finalized. Fix
that, according to the actual flash layout:
dev:    size   erasesize  name
mtd0: 00140000 00020000 "fota-flag"
mtd1: 00140000 00020000 "caldata"
mtd2: 00140000 00020000 "mac"
mtd3: 00f40000 00020000 "ubiconcat0"
mtd4: 00400000 00020000 "kernel"
mtd5: 06900000 00020000 "ubiconcat1"
mtd6: 00080000 00010000 "u-boot"
mtd7: 00020000 00010000 "u-boot-env"
mtd8: 07840000 00020000 "ubi"

Fixes: 8c78a13bfc ("ath79: support ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-02-20 14:04:38 +01:00
Christian Lamparter
5696244ae2 ipq806x: disable Linksys EA7500v1 and EA8500
The kernel of both images will no longer fit into
the 3072KiB / 3MiB kernel partition:
|Image Name:   ARM OpenWrt Linux-5.10.100
|Created:      Sat Feb 19 00:11:55 2022
|Image Type:   ARM Linux Kernel Image (uncompressed)
|Data Size:    3147140 Bytes = 3073.38 KiB = 3.00 MiB

Disable both targets for now, until a solution is available.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-20 14:04:38 +01:00
Christian Lamparter
c062087a6c mpc85xx: fix KEY_RFKILL vs KEY_RFKill
This fixes a buildbot builder error:
Error: arch/powerpc/boot/dts/tl-wdr4900-v1.dts:245.18-19 syntax error

Fixes: 256e1dbc7d ("mpc85xx: utilize dt-binding definitions for keys + gpios")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-20 14:04:38 +01:00
Petr Štetiar
d8bf730fe0 netifd: bump to version 2022-02-20
Contains following changes:

 136006b88826 cmake: fix usage of implicit library and include paths
 bc0e84d689e2 netifd: interface-ip: don't set fib6 policies if ipv6 disabled

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-02-20 10:52:55 +01:00
Nick McKinney
61d97bf377 ramips: clean up Makefile formatting
Use correct indent in target/linux/ramips/image/mt7621.mk
to be consistent with the rest of the file.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
[rephrase commit message as Adrian suggested, fix a6004ns-m indent]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-20 16:16:43 +09:00
Sven Roederer
65df862b50 ramips: mt7621: print size of factory initramfs-image if it's too big
It's helpful to know the current and maximal size of the imagefiles if the
creation fails.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2022-02-20 15:55:36 +09:00
Graham Cole
e282e50d44 ath79: fix wndr4500v3 lan port order to match case
The LED and LAN port numbering on the case of wndr4500v3 devices are
reversed relative to the wndr4300v2. I created this patch to so that the
ordering in OpenWRT will be consistent with that.

Signed-off-by: Graham Cole <diakka@gmail.com>
2022-02-20 13:54:12 +09:00
Yoonji Park
125b9aec29 ramips: add support for ipTIME A3002MESH
Add support for ipTIME A3002MESH.

Hardware:
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: XMC XM25QH128AHIG (SPI-NOR 16MB)
- WiFi: MediaTek MT7615D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x2, SoC built-in)
- UART: [GND, RX, TX, 3.3V] (57600 8N1, J4)

MAC addresses:
| interface |        MAC        |     source     | comment
|-----------|-------------------|----------------|----------
|       LAN | 70:XX:XX:5X:XX:X3 |                |
|       WAN | 70:XX:XX:5X:XX:X1 | u-boot 0x1fc40 |
|   WLAN 2G | 72:XX:XX:4X:XX:X0 |                |
|   WLAN 5G | 70:XX:XX:5X:XX:X0 | factory 0x4    |
|           | 70:XX:XX:5X:XX:X0 | u-boot 0x1fc20 | unknown
|           | 70:XX:XX:5X:XX:X2 | factory 0x8004 | unknown

- WLAN 2G MAC address is not the same as stock firmware since OpenWrt
  uses LAN MAC address with local bit sets.

Installation:
1. Flash initramfs image. This can be done using stock web ui or TFTP
2. Connect to OpenWrt with an SSH connection to 192.168.1.1
3. Perform sysupgrade with sysupgrade image

Revert to stock firmware:
- Flash stock firmware via OEM TFTP Recovery mode
- Perform sysupgrade with stock image

TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1

Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
[wrap/rephrase commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-20 13:53:15 +09:00
Sungbo Eo
9968a909c2 Revert "ramips: increase spi-max-frequency for ipTIME mt7620 devices"
This reverts commit 13a185bf8a.

There was a report that one A1004ns device fails to detect its flash
chip correctly:

[    1.470297] spi-nor spi0.0: unrecognized JEDEC id bytes: e0 10 0c 40 10 08
[    1.484110] spi-nor: probe of spi0.0 failed with error -2

It also uses a different flash chip model:
* in my hand: Winbond W25Q128FVSIG (SOIC-8)
* reported: Macronix MX25L12845EMI-10G (SOP-16)

Reducing spi-max-frequency solved the detection failure. Hence revert.

Reported-by: Koasing <koasing@gmail.com>
Tested-by: Koasing <koasing@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-20 13:47:57 +09:00
Sungbo Eo
19a90262df wireless-regdb: update to version 2022.02.18
e061299 wireless-regdb: Raise DFS TX power limit to 250 mW (24 dBm) for the US
2ce78ed wireless-regdb: Update regulatory rules for Croatia (HR) on 6GHz
0d39f4c wireless-regdb: Update regulatory rules for South Korea (KR)
acad231 wireless-regdb: Update regulatory rules for France (FR) on 6 and 60 GHz
ea83a82 wireless-regdb: add support for US S1G channels
4408149 wireless-regdb: add 802.11ah bands to world regulatory domain
5f3cadc wireless-regdb: Update regulatory rules for Spain (ES) on 6GHz
e0ac69b Revert "wireless-regdb: Update regulatory rules for South Korea (KR)"
40e5e80 wireless-regdb: Update regulatory rules for South Korea (KR)
e427ff2 wireless-regdb: Update regulatory rules for China (CN)
0970116 wireless-regdb: Update regulatory rules for the Netherlands (NL) on 6GHz
4dac44b wireless-regdb: update regulatory database based on preceding changes

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-20 13:47:57 +09:00
Sungbo Eo
3e3e78de11 ath79: utilize nvmem on Netgear EX7300 v2
mtd-mac-address should no longer be used after commit 5ae2e78639
("kernel: drop support for mtd-mac-address"). Convert it to nvmem-cells.

While at it, also convert OpenWrt's custom mtd-cal-data property and
userspace pre-calibration data extraction to the nvmem implementation.

Note: nvmem-cells in QCN5502 wmac has not been tested.

Fixes: c32008a37b ("ath79: add partial support for Netgear EX7300v2")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-20 13:45:06 +09:00
Christian Lamparter
b0d5939b80 apm821xx: WNDR4700: use upstream tc654 cooling devices
Upstream hwmon-maintainer had various comments about
the changes to the tc654 driver. These have been
addressed and the cooling device support is destined
for inclusion.

One of the comments was the change of the cooling states
scaling. No longer the driver uses the same values as the
hwmon interface, instead the states are now the 17 states
the tc654 supports.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 19:34:18 +01:00
Christian Lamparter
2aa97ecb59 kernel: add kmod-hwmon-lm70 support
package hwmon's lm70.ko. This module supports the
National Semiconductor/TI LM70,LM71,LM74 and
TI TMP121,TMP122,TMP123 and TMP124 chips (all SPI).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 19:34:18 +01:00
Christian Lamparter
2db231e77a mpc85xx: add HiveAP-350 alternative name for HiveAP-330
The HiveAP-350 has six external antennas connectors.
(It also has twice the flash?)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 19:34:18 +01:00
Christian Lamparter
256e1dbc7d mpc85xx: utilize dt-binding definitions for keys + gpios
include the device-tree binding headers that provide definitions
for keys codes and gpios in the device-tree files.

Random bonus: merge tl-wdr4900-v1's uboot with the nvmem-node.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 19:34:18 +01:00
Christian Lamparter
c7528996a5 mpc85xx: change legacy "eeprom" compatible
silences the following message:
> eeprom 0-0051: eeprom driver is deprecated, please use at24 instead

The chip was likely a Dallas Semiconductor and later MAXIM part
before Analog Devices, Inc. bought MAXIM.

From the datasheet:

"The DS28CN01 combines 1024 bits of EEPROM with challenge-and-response
authentication security implemented with the FIPS 180-1/180-2 and
ISO/IEC 10118-3 Secure Hash Algorithm (SHA-1)."

...

"Write Access Requires Knowledge of the Secret
and the Capability of Computing and Transmitting
a 160-Bit MAC as Authorization"

OpenWrt doesn't use it. There's no in-kernel driver
from what I know. Let's document that the chip is
at the location.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 19:34:18 +01:00
Christian Lamparter
583ac0e11d mpc85xx: update lp5521 led-controller node for 5.10
The tricolor LED which is controlled by a lp5521 needed
some maintenance as the driver failed to load in the
current v5.10 image:
| lp5521: probe of 0-0032 failed with error -22

This is because the device-tree needed to be updated
to match the latest led coloring and function trends.

 - removed the device name from the label
 - added color/function properties
 - added required reg and cells properties

For reference a disabled multicolor/RGB is added since this
reflects the real hardware. Unfortunately, the multicolor
sysfs interface isn't supported by yet.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 19:34:18 +01:00
Martin Kennedy
cfe79f2eb8 mpc85xx: Patch HiveAP 330 u-boot to fix boot
When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too
large upon decompression (>7MB or so) to decompress itself on boot (see
FS#4110[1]).

There have been many attempts to fix booting from a compressed kernel on
the HiveAP-330:

- b683f1c36d ("mpc85xx: Use gzip compressed kernel on HiveAP-330")
- 98089bb8ba ("mpc85xx: Use uncompressed kernel on the HiveAP-330")
- 26cb167a5c ("mpc85xx: Fix Aerohive HiveAP-330 initramfs image")

We can no longer compress the kernel due to size, and the stock bootloader
does not support any other types of compression. Since an uncompressed
kernel no longer fits in the 8MiB kernel partition at 0x2840000, we need to
patch u-boot to autoboot by running variable which isn't set by the
bootloader on each autoboot.

This commit repartitions the HiveAP, requiring a new COMPAT_VERSION,
and uses the DEVICE_COMPAT_MESSAGE to guide the user to patch u-boot,
which changes the variable run on boot to be `owrt_boot`; the user can
then set the value of that variable appropriately.

The following has been documented in the device's OpenWrt wiki page:
<https://openwrt.org/toh/aerohive/hiveap-330>. Please look there
first/too for more information.

The from-stock and upgrade from a previous installation now becomes:

0) setup a network with a dhcp server and a tftp server at serverip
(192.168.1.101) with the initramfs image in the servers root directory.

1) Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted. If the password
doesn't work. Try reseting the device by pressing and holding the reset
button with the stock OS.

2) Once in U-Boot, set the new owrt_boot and tftp+boot the initramfs image:
   Use copy and paste!

 # fw_setenv owrt_boot 'setenv bootargs \"console=ttyS0,$baudrate\";bootm 0xEC040000 - 0xEC000000'
 # save
 # dhcp
 # setenv bootargs console=ttyS0,$baudrate
 # tftpboot 0x1000000 192.168.1.101:openwrt-mpc85xx-p1020-aerohive_hiveap-330-initramfs-kernel.bin
 # bootm

3) Once openwrt booted:
carefully copy and paste this into the root shell. One step at a time

  # 3.0 install kmod-mtd-rw from the internet and load it

  opkg update; opkg install kmod-mtd-rw
  insmod mtd-rw i_want_a_brick=y

  # 3.1 create scripts that modifies uboot

cat <<- "EOF" > /tmp/uboot-update.sh
  . /lib/functions/system.sh
  cp "/dev/mtd$(find_mtd_index 'u-boot')" /tmp/uboot
  cp /tmp/uboot /tmp/uboot_patched
  ofs=$(strings -n80 -td < /tmp/uboot | grep '^ [0-9]* setenv bootargs.*cp\.l' | cut -f2 -d' ')
  for off in $ofs; do
    printf "run owrt_boot;            " | dd of=/tmp/uboot_patched bs=1 seek=${off} conv=notrunc
  done
  md5sum /tmp/uboot*
EOF

  # 3.2 run the script to do the modification

  sh /tmp/uboot-update.sh

  # verify that /tmp/uboot and /tmp/uboot_patched are good
  #
  # my uboot was: (is printed during boot)
  # U-Boot 2009.11 (Jan 12 2017 - 00:27:25), Build: jenkins-HiveOS-Honolulu_AP350_Rel-245
  #
  # d84b45a2e8aca60d630fbd422efc6b39  /tmp/uboot
  # 6dc420f24c2028b9cf7f0c62c0c7f692  /tmp/uboot_patched
  # 98ebc7e7480ce9148cd2799357a844b0  /tmp/uboot-update.sh <-- just for reference

  # 3.3 this produces the /tmp/u-boot_patched file.

  mtd write /tmp/uboot_patched u-boot

3) scp over the sysupgrade file to /tmp/ and run sysupgrade to flash OpenWrt:

  sysupgrade -n /tmp/openwrt-mpc85xx-p1020-aerohive_hiveap-330-squashfs-sysupgrade.bin

4) after the reboot, you are good to go.

Other notes:

- Note that after this sysupgrade, the AP will be unavailable for 7 minutes
  to reformat flash. The tri-color LED does not blink in any way to
  indicate this, though there is no risk in interrupting this process,
  other than the jffs2 reformat being reset.

- Add a uci-default to fix the compat version. This will prevent updates
  from previous versions without going through the installation process.

- Enable CONFIG_MTD_SPLIT_UIMAGE_FW and adjust partitioning to combine
  the kernel and rootfs into a single dts partition to maximize storage
  space, though in practice the kernel can grow no larger than 16MiB due
  to constraints of the older mpc85xx u-boot platform.

- Because of that limit, KERNEL_SIZE has been raised to 16m.

- A .tar.gz of the u-boot source for the AP330 (a.k.a. Goldengate) can
  be found here[2].

- The stock-jffs2 partition is also removed to make more space -- this
  is possible only now that it is no longer split away from the rootfs.

- the console-override is gone. The device will now get the console
  through the bootargs. This has the advantage that you can set a different
  baudrate in uboot and the linux kernel will stick with it!

- due to the repartitioning, the partition layout and names got a makeover.

- the initramfs+fdt method is now combined into a MultiImage initramfs.
  The separate fdt download is no longer needed.

- added uboot-envtools to the mpc85xx target. All targets have uboot and
  this way its available in the initramfs.

[1]: https://bugs.openwrt.org/index.php?do=details&task_id=4110
[2]: magnet:?xt=urn:btih:e53b27006979afb632af5935fa0f2affaa822a59

Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(rewrote parts of the commit message, Initramfs-MultiImage,
dropped bootargs-override, added wiki entry + link, uboot-envtools)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 19:20:29 +01:00
Rosen Penev
fbb8e1ef45 ksmbd: add out-of-tree module
ksmbd is an upstream linux alternative to Samba which is lighterweight
and more performant, especially on underpowered devices.

Moving it here from the packages feed as it is now an upstream kernel
module. Also easier to update as version updates can be coordinated better

The next LTS kernel (5.15) has this included. A depend on kernel < 5.15
will need to be added later.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-02-19 18:29:42 +01:00
Rosen Penev
666d427652 linux/modules: split up oid_registry
This will be needed by ksmbd in a following commit.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-02-19 18:29:42 +01:00
Rosen Penev
63f32eb88e target/linux: add help text to kernel config
These options will be used for ksmbd. Once kernel 5.15
makes it in, this patch can go away.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-02-19 18:29:42 +01:00
Raylynn Knight
6905ad2494 x86: fix support for Sophos SG/XG wireless products
Correct typo that caused network interfaces for Sophos
SG/XG wireless devices to not be configured properly.

Tested on Sophos SG 135wr2, Sophos XG 125wr2 and
Sophos SG 105wr1

Signed-off-by: Raylynn Knight <rayknight@me.com>
2022-02-19 18:29:42 +01:00
Enrico Mioso
22436d762b mvebu: mark all mtd partitions on GL.iNet GL-MV1000 read-only
On this device, two of the three defined MTD partitions are
automatically set to read-only, since they do not end at an
erase/write block boundary.

In particular, the only partition remaining writable is the
one holding the u-boot bootloader.

Mark all of the partitions read-only, at least until a better
understanding of why the layout has been laid out this way is
gained.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2022-02-19 18:29:42 +01:00
John Audia
c5dca80526 ipq806x: update defconfig
Enabled `CONFIG_ALL_KMODS` and ran `make kernel_menuconfig` against
ipq806x to update defconfig.

The removed symbols are in fact present in
target/linux/generic/config-5.10. CONFIG_MDIO_DEVRES
was likely added due to this:
<https://elixir.bootlin.com/linux/v5.10.100/source/drivers/net/phy/Kconfig#L16>

Signed-off-by: John Audia <graysky@archlinux.us>
2022-02-19 18:29:42 +01:00
Christian Lamparter
c420947bb3 ipq806x: TP-Link VR2600v convert legacy partitioning
This device still had the legacy flash partitioning.
This is a problem, because neither the nvmem-cells
for mac-address and calibration. Nor the denx,uimage
mtd-splitter compatible would be picked up.

The patch also changes the node-names of the flash
and partition nodes to hopefully meet all the
current FDT trends.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 18:29:42 +01:00
Christian Lamparter
80d34d9d59 ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200
Enrico provided a bootlog that shows the chip is a WAVE-2 QCA9888v2:

> pci 0000:01:00.0: [168c:0056] type 00 class 0x028000
> [...]
> ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x56.
> ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 [...] chip_id 0x00000000 sub 0000:0000
> ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5  features mfp,[...]
> ath10k_pci 0000:01:00.0: board_file api 2 bmi_id N/A crc32 6535d835
> ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 32 raw 0 hwcrypto 1

this patch switches the device over to pre-calibration.
(this is more or less cosmetic)

Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 18:29:42 +01:00
Enrico Mioso
7270c9f8f6 ipq40xx: limit available radio channels for GL.iNet GL-B2200
The PCIe and built-in 5GHZ radios are meant to operate on different
frequency bands. The hardware enforces this via RF filters.
Add this information to allow software enforcing it as well.
Credits to Piotr Dymacz for the invaluable help.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2022-02-19 18:29:42 +01:00
Christian Lamparter
b45f3c435a apm821xx: add alternative names for supported devices
with the introduction of the DEVICE_ALTX_VENDOR, DEVICE_ALTX_MODEL
multiple/sibiling devices can seemingly supported by one device entry.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 18:27:40 +01:00
Nick Hainke
2fd049f5cd ramips: add Ubiquiti EdgePoint R6 as alt name
The Ubiquiti EdgePoint R6 is identical to the EdgeRouter X SFP.
However, it fits well into outdoor environments due to its water-proven
case.

More specifications: 9715beb04c ("ramips: add support for Ubiquiti
EdgeRouter X-SFP")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-02-19 17:26:37 +01:00
Eneas U de Queiroz
e6df13d0e1 hostapd: fallback to psk when generating r0kh/r1kh
The 80211r r0kh and r1kh defaults are generated from the md5sum of
"$mobility_domain/$auth_secret".  auth_secret is only set when using EAP
authentication, but the default key is used for SAE/PSK as well.  In
this case,  auth_secret is empty, and the default value of the key can
be computed from the SSID alone.

Fallback to using $key when auth_secret is empty.  While at it, rename
the variable holding the generated key from 'key' to 'ft_key', to avoid
clobbering the PSK.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[make ft_key local]
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-02-19 16:14:52 +01:00
David Bauer
6f78723977 hostapd: add STA extended capabilities to get_clients
Add the STAs extended capabilities to the ubus STA information. This
way, external daemons can be made aware of a STAs capabilities.

This field is of an array type and contains 0 or more bytes of a STAs
advertised extended capabilities.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-02-19 16:14:45 +01:00
David Bentham
e3166643fb net: ethernet: mtk_eth_soc: add ipv6 flow offload support
Add the missing IPv6 flow offloading support for routing only.
Hardware flow offloading is done by the packet processing engine (PPE)
of the Ethernet MAC and as it doesn't support mangling of IPv6 packets,
IPv6 NAT cannot be supported.

Signed-off-by: David Bentham <db260179@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-02-19 15:00:16 +01:00
Eneas U de Queiroz
009293c52e build: scripts/config - update to kconfig-v5.14
Functional Changes
---------- -------
- make 'imply' not impose any restrictions: allow symbols implied by y
  to become m
- change "modules" from sub-option to first-level attribute

Bugfixes
--------
- nconf: fix core dump when searching in empty menu
- nconf: stop endless search loops
- xconfig: fix content of the main widget
- xconfig: fix support for the split view mode

Other Changes
----- -------
- highlight xconfig 'comment' lines with '***'
- xconfig: navigate menus on hyperlinks
- xconfig: drop support for Qt4
- improve host ncurses detection

Update the 'option modules' usage to just 'modules' in Config.in.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2022-02-19 13:10:01 +01:00
Daniel González Cabanelas
73ea763c0d ath79: Add support for Ubiquiti NanoBeam AC Gen1 XC
The Ubiquiti NanoBeam AC Gen1 XC (NBE-5AC-19) is an outdoor 802.11ac CPE
with a waterproof casing (ultrasonically welded) and bulb shaped.

Hardware:
 - SoC: Qualcomm Atheros QCA9558
 - RAM: 128 MB DDR2
 - Flash: 16 MB SPI NOR
 - Ethernet: 1x GbE, AR8033 phy connected via SGMII
 - PSU: 24 Vdc passive PoE
 - WiFi 5 GHz: Qualcomm Atheros QCA988X
 - Buttons: 1x reset
 - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue
 - Internal antenna: 19 dBi planar

Installation from stock airOS firmware:
 - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at
   https://openwrt.org/toh/ubiquiti/common

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2022-02-19 13:10:01 +01:00
Alexey Smirnov
66071729a2 base-files: add support for heartbeat led trigger
This patch adds support for creation heartbeat led trigger with,
for example, this command:

	ucidef_set_led_heartbeat "..." "..." "..."

from /etc/board.d/01_leds.

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2022-02-19 13:10:01 +01:00
Paul Fertser
e1e4cbde5c x86: geode: add kmod-crypto-ebc needed for hw acceleration
Module kmod-crypto-hw-geode provides accelerated cbc(aes) and ecb(aes)
but the software implementation is also needed when AES key size isn't
128 so that the operation can fall back. Add the kmod so that it would
all work as expected out of the box.

Tested-by: timur_davletshin
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2022-02-19 13:10:01 +01:00
Mauri Sandberg
2c211a901d gpio-nxp-74hc153: remove package
This module was used solely by Buffalo WZR-HP-G300NH devices
and has become obsolete with the introduction of gpio-cascade.

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
2022-02-19 13:10:01 +01:00
Mauri Sandberg
b99aee5080 ath79: use gpio-cascade for Buffalo WZR-HP-G300NH
Switch to a generic GPIO cascade driver.

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
2022-02-19 13:10:01 +01:00
Mauri Sandberg
2f50d65161 kernel: add package kmod-gpio-cascade
Adds kernel module for Generic GPIO cascade.

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
2022-02-19 13:10:01 +01:00
Mauri Sandberg
15f0074beb kernel: add package kmod-multiplexer
Adds new kernel module for GPIO controlled multiplexer support.

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
2022-02-19 13:10:01 +01:00