Instead of duplicating the '/sbin/setfiles' binary, have
'/sbin/restorecon' as yet another alias for
'/sbin/policycoreutils-setfiles'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Expose WPS ubus API only if compiled with WPS support and add new
handler for wps_status call.
Also add '-v wps' option to check whether WPS support is present in
hostapd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[cut out of bigger patch, alter use of DEVICE_VARIANT, merge case
in 01_leds, use lower case for v4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for various targets, this removes
the "devicename" from LED labels in rtl838x, as it's useless and
only creates complexity.
Since the target is fresh and so far only system LEDs were added,
this does not add a migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The syntax of the shared SoC DTSI file determines the DTS version,
so no need to repeat the "/dts-v1/;" identifier in every file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The idea of commit a14f5bb4bd was to use wpad-basic-wolfssl
consistently throughout the whole trunk, so use it here as well.
Fixes: 50fdddae05 ("BPi-M2U kernel modules for onboard WiFi")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix wrong magic number verification for FW files.
Correct handling of external RTL8218B firmware PHY name in firmware.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
build: always build package/kernel/linux
If no in-tree module packages are selected, the build system does not process
package/kernel/linux. This package is required for building the virtual
'kernel' package, which is specified as a dependency for all kernel packages.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The router profile installs many packages unnecessary for
the operation of a typical ethernet switch. Instead of creating
an empty switch profile upfront, use the basic profile until
a set of common packages crystallizes.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
Fixes long delay on boot when booting from flash. The driver waits
for one minute for userspace to load firmware, before it becomes
available.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
This adds basic support for reading the internal PHYs of the RTL839x SoCs
and full support for the 2 PHYs connected to the 1000Base-X SerDes of
the RTL8393 SoC.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds correct interrupt routing settings for IRQs on the RTL839x SoCs.
It also speeds up irq handling based on work by biot for all SoCs.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
The vDSO is used to accelerate some syscalls. It should work fine wherever it's
available, so enable it globally for all targets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Specification
CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
DDR3 RAM: 256MB/512MB
Connectivity: 10/100/1000Mbps Ethernet
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input only
Debug Serial Port: 4Pin, 2.54 mm pitch pin header
Power Supply: DC 5V/2A
PCB Dimension: 40 x 40 x 1.2mm
Installation:
Burn the image file to an SD Card with dd or any image burning tool
Boot ZeroPi from the SD Card
The following features are working and tested:
Ethernet port 10/100/1000M Ethernet
Remarks: SBC is mostly compatible and boots with FriendlyARM NanoPI M1 plus DTS also (zeropi has no working hdmi)
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Tested on a A20 board:
$ cat /proc/asound/cards
0 [SPDIF ]: On-board_SPDIF - On-board SPDIF
On-board SPDIF
Size of the module for a 32bit kernel:
60708 linux-5.4.66/sound/soc/sunxi/sun4i-spdif.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
Size of the modules for a Cortex A7 build:
43920 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-rx.ko
44044 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-tx.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
Mainline u-boot dynamically passes the mtd partitions via devicetree:
$ cat /proc/mtd
dev: size erasesize name
mtd0: 003f0000 00001000 "firmware"
mtd1: 00010000 00001000 "u-boot-env"
Add support for this setup.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.
Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware
Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This option is now activated in the generic kernel configuration, no
need to do it for a specific package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This config option was moved to the generic kernel configuration.
Fixes: ab1bd57656 ("kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
u-boot binaries are not useful for these boards, they need to be combined
with atf for a proper firmware.
Signed-off-by: Andre Heider <a.heider@gmail.com>
u-boot binaries for this SoC are only required for the atf package,
disable them per default so they don't get build unnecessarily.
Signed-off-by: Andre Heider <a.heider@gmail.com>
correct oversight on setting regulatory country and mac address of wireless configuration
change method of retrieving mac address
The MAC address for eth0 is rad out of the devinfo partition in some
other initial configuration script already.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
correct device CC oversight
Set the initial wifi configuration like for the other similar Linksys
devices.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
This commit contains patches for PCI aardvark driver and relevant DTS
changes for Turris MOX and EspressoBin backported from mainline kernel.
It fixes support for old ATF, various wifi cards, mainly Compex WLE900VX.
Signed-off-by: Pali Rohár <pali@kernel.org>
Explicitly set the QEMU cpu type and support the MIPS R2 ISA, for both
64-bit and 32-bit targets. The later previously supported MIPS R2 by
implicit default.
This is needed after commit 93608697f3 ("malta: update MIPS64 ISA to R2"),
otherwise booting malta images with scripts/qemustart will hang.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Usage of current R1 ISA is inconsistent with the MIPS32 subtarget, little
used and has limited utility for testing.
Many distros target a minimum R2 ISA. Debian MIPS 32-bit/64-bit ports all
use MIPS R2 ISA since Stretch, for example. Fedora's MIPS arch also targets
the R2 ISA for 32-bit/64-bit.
Widely used MIPS64 platforms like Octeon are based on the MIPS R2 ISA or
later, and benefit from having a compatible test platform in OpenWRT.
While Linux does support MIPS64 R1 targets, its usefulness for development
and testing is limited. As an example, the modern Linux eBPF JIT requires
a MIPS R2 ISA or later.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[Refresh config and fix README]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If you compile first libaudit library and then trace-cmd package,
compilations fails with:
Package trace-cmd is missing dependencies for the following libraries:
libaudit.so.1
If you enable libaudit for trace-cmd, it will show system name calls while using command profile.
Try to be slim as much as possible - libaudit .ipk has 42,4 kB.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
libzstd from the packages feed gets picked up. Remove it.
Fixes:
Package perf is missing dependencies for the following libraries:
libzstd.so.1
Signed-off-by: Rosen Penev <rosenp@gmail.com>
For this package CFLAGS have to be passed via EXTRA_CFLAGS.
On arm this bug causes build to fail because no -fPIC is present in CFLAGS.
Signed-off-by: Marek Behún <kabel@blackhole.sk>
This package fails with a strange error when building with musl when NLS
is enabled. The configuration thinks that libelf is not present, even
though DEPENDS contains +libelf, because when NLS is enabled, libelf.so
depends on libintl, and the correct LDFLAGS are missing for
libintl-full. This then causes the configuration script to check for
glibc, but this fails because we are using musl.
Signed-off-by: Marek Behún <kabel@blackhole.sk>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
Like done for other targets recently, put the dts-v1 statement
into the top-level SoC-based DTSI files, and remove all other
occurences.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
After the LED labels have been made more general by removing
the model names, we can move several definitions to DTSI files
to reduce the amount of duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for various targets, this will remove
the "devicename" from LED labels in bcm63xx, as it's useless and
only creates complexity.
The devicename is removed in DTS files and 01_leds, merging
several cases on the way. A migration script is added for
existing configurations.
Note that a few labels were using "model::function" scheme without
color specified, those were converting to just "function" and the
necessary migrations were added to the migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
