Add support for the ZTE MF281 battery-powered WiFi router.
Hardware
--------
SoC: Qualcomm Atheros QCA9563
RAM: 128M DDR2
FLASH: 2M SPI-NOR (GigaDevice GD25Q16)
128M SPI-NAND (GigaDevice)
WLAN: QCA9563 2T2R 802.11 abgn
QCA9886 2T2R 802.11 nac
WWAN: ASRMicro ASR1826
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1
Unpopulated connector next to SIM slot
(SIM) GND - RX - TX - 3V3
Don't connect 3V3
BUTTON: Reset - WPS
LED: 1x debug-LED (internal)
LEDs on front of the device are controlled
using the modem CPU and can not be controlled
by OpenWrt
Installation
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.1.66 to the ethernet port.
Serve the OpenWrt initramfs image as "speedbox-2.bin"
3. Boot the initramfs image using U-Boot
$ setenv serverip 192.168.1.66
$ setenv ipaddr 192.168.1.154
$ tftpboot 0x84000000 speedbox-2.bin
$ bootm
4. Copy the OpenWrt factory image to the device using scp and write to
the NAND flash
$ mtd write /path/to/openwrt/factory.bin firmware
WWAN
----
The WWAN card can be used with OpenWrt. Example configuration for
connection with a unauthenticated dual-stack APN:
network.lte=interface
network.lte.proto='ncm'
network.lte.device='/dev/ttyACM0'
network.lte.pdptype='IPV4V6'
network.lte.apn='internet.telekom'
network.lte.ipv6='auto'
network.lte.delay='10'
The WWAN card is running a modified version of OpenWrt and handles
power-management as well as the LED controller (AW9523). A root shell
can be acquired by installing adb using opkg and executing "adb shell".
Signed-off-by: David Bauer <mail@david-bauer.net>
Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only include recovery image in SD card image generated for the
BananaPi BPi-R3 if building with CONFIG_TARGET_ROOTFS_INITRAMFS.
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Pakedge WR-1 is a dual-band wireless router.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
1. 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Rename initramfs image to:
openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
reset button. Hold the button, on the lates bootloader version, when
Power and WiFi-5 LEDs will start blinking release it. For the older
bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
minute) the Power LED will start blinking, when stops, router is fully
booted.
4. Connect to one of LAN ports and use SSH to open the shell at
192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
at some point, You want to go back to original firmware. The firmware
provided by manufacturer on its site is encrypted and U-Boot accepts
only decrypted factory images, so there's no way to restore original
firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
LED will start blinking, wait till it stops, then router is ready for
configuration.
Additional information
U-Boot command line is password protected. Password is unknown.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Devices using GPT usually have FAT filesystem on boot partition and
that's where the intermediary backup of system configuration is stored
on sysupgrade. Automatic restoring of OpenWrt configuration after
sysupgrade will be inhibited if the driver is not loaded and file system
type is not specified in mount command.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
The patch 921-mt7986-add-mmc-support.patch introduced by commit
dabcaac443 ("mediatek: add mt7986 soc support to the target") has never
been applied in a way that it would have any effect as it actually
created a file target/linux/generic/patches-5.15/... in the kernel tree
and was probably a patch intended to be applied to openwrt.git instead
of being put into kernel patches folder as a file.
As an upstream commit from vanilla Linux also adding support for MT7986
to the mtk-sd driver has already been included we can remove that old
patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update host build of fiptool and use the new python sptool.py instead
of the previous sptool executable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update to latest version. Replace mirror with @GNU/bc.
Manually refresh:
- 001-no_doc.patch
Add patch found here:
26f275502d
as 002-fix-libmath.patch to fix compilation.
Add another patch found here:
55b26eda94
as 003-bc-fix-hang.patch to prevent a hang when building the kernel.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Previous commit forgot to refresh the patches.
This commit refreshes the patches:
- 120-curl-fix-libressl-linking.patch
- 130-bootstrap_parallel_make_flag.patch
Fixes: 3b2f19271c ("tools/cmake: update to 3.24.1")
Signed-off-by: Nick Hainke <vincent@systemli.org>
The introduction of the new Airoha target has left the tree in an
unfresh state. Refresh patches to improve that situation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch was added in 09b086eeca
("kernel: add quirk for Huawei-compatible OEM SFP GE-T"). Add patch
title, description and SoB to follow OpenWrt's developer guide for
working patches to prepare it for being sent upstream. This patch
should be discussed with Russell King and merged to Linux kernel.
Co-authored-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It was reported on Turris forum [1] that HALNy HL-GSFP module does not
work as it should with kernel 5.15. Russell King prepared this patch
series, which fixes broken SFP module to work.
Compile and run tested with Turris Omnia.
[1] https://forum.turris.cz/t/hbl-turrisos-6-0-alpha2-halny-hl-gsfp-sfp-gpon-stick-problems/17547
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
There are two feature currently altered by the multicast_to_unicast option.
1. bridge level multicast_to_unicast via IGMP snooping
2. hostapd/mac80211 config multicast_to_unicast setting
The hostapd/mac80211 setting has the side effect of converting *all* multicast
or broadcast traffic into per-station duplicated unicast traffic, which can
in some cases break expectations of various protocols.
It also has been observed to cause ARP lookup failure between stations
connected to the same interface.
The bridge level feature is much more useful, since it only covers actual
multicast traffic managed by IGMP, and it implicitly defaults to 1 already.
Renaming the hostapd/mac80211 option to multicast_to_unicast_all should avoid
unintentionally enabling this feature
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It shouldn't be needed anymore as we've now `scripts/xxdi.pl`, which
should be self contained and fully compatible `xxd -i` replacement.
Fixes: #10555
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Dependency on xxd was added in commit c4dd2441e7 ("tools: add xxd
(from vim)") as U-Boot requires xxd to create the default environment
from an external file.
Later in commit 2b94aac7a1 ("tools: xxd: use more convenient source
tarball"), xxd from another source was used instead, but that source is
currently unavailable, so let's fix it by using simple xxdi.pl Perl
script instead.
Fixes: #10555
Signed-off-by: Petr Štetiar <ynezz@true.cz>
So it can serve as a standalone drop in replacement for xxd utility used
currently mostly in U-Boot packages with `xxd -i` mode which outputs C
include file style, with aim for byte to byte identical output, so the
eventual difference in the generated output is easily spottable.
Fixes: #10555
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jo-Philipp Wich <jo@mein.io> [perl-fu]
xxdi.pl is a Perl script that implements vim's 'xxd -i' mode so that
packages do not have to use all of vim just to get this functionality.
References: #10555
Source: 97a6bd5cee/xxdi.pl
Signed-off-by: Petr Štetiar <ynezz@true.cz>
A line in platform.sh was accidentally removed when adding support
for the Bananapi BPi-R3.
Re-add it to fix sysupgrade on the MTK7986 rfba AP.
Fixes: a96382c1bb ("mediatek: add support for Bananapi BPi-R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All subtargets are using now 5.15 as testing kernel.
Move KERNEL_TESTING_PATCHVER:=5.15 to the common Makefile.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Devices with SMALL_FLASH enabled have "SQUASHFS_BLOCK_SIZE=1024" in
their config. This significantly increases the cache memory required by
squashfs [0]. This commit enables low_mem leading to a much better
performance because the SQUASHFS_BLOCK_SIZE is reduced to 256.
Example Nanostation M5 (XM):
The image size increases by 128 KiB. However, the memory statisitcs look
much better:
Default tiny build:
------
MemTotal: 26020 kB
MemFree: 5648 kB
MemAvailable: 6112 kB
Buffers: 0 kB
Cached: 3044 kB
low_mem enabled:
-----
MemTotal: 26976 kB
MemFree: 6748 kB
MemAvailable: 11504 kB
Buffers: 0 kB
Cached: 7204 kB
[0] - 7e8af99cf5
Signed-off-by: Nick Hainke <vincent@systemli.org>
Hardware
--------
Qualcomm IPQ4029 WiSoC
2T2R 802.11 abgn
2T2R 802.11 nac
Macronix MX25L25635E SPI-NOR (32M)
512M DDR3 RAM
1x Gigabit LAN
1x Cisco RJ-45 Console port
Settings: 115200 8N1
Installation
------------
1. Attach to the Console port. Power up the device and press the s key
to interrupt autoboot.
2. The default username / password to the bootloader is admin / new2day
3. Update the bootcommand to allow loading OpenWrt.
$ setenv ramboot_openwrt "setenv serverip 192.168.1.66;
setenv ipaddr 192.168.1.1; tftpboot 0x86000000 openwrt-3915.bin;
bootm"
$ setenv boot_openwrt "sf probe;
sf read 0x88000000 0x280000 0xc00000; bootm 0x88000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
4. Download the OpenWrt initramfs image. Serve it using a TFTP server as
"openwrt-3915.bin" at 192.1681.66.
5. Download & boot the OpenWrt initramfs image on the access point.
$ run ramboot_openwrt
6. Wait for OpenWrt to start.
7. Download and transfer the sysupgrade image to the device using e.g.
SCP.
8. Install OpenWrt to the device using "sysupgrade"
$ sysupgrade -n /path/to/openwrt.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
