Select matching U-Boot for both v1 and v2 variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223
Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
7. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | A4:xx:xx:51:xx:F4 | No MACs was |
| LAN | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN | A4:xx:xx:51:xx:F4 | [1] |
| WLAN_2g | A4:xx:xx:51:xx:F5 | |
| WLAN_5g | A6:xx:xx:21:xx:F5 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
"Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
MTS WG430223 devices even within the same broadcast domain.
Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset | | Description |
+==============+===============+========================================+
| 0x0 | 31 52 48 53 | TRX magic "1RHS" |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.
Specifications
--------------
* Device: ZyXEL GS1900-24E
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet: 24x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Switch: 1 Power switch on rear of device
* Power 120-240V AC C13
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Buidbots are currently choking on the following compile error:
In file included from tools/aisimage.c:9:
include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory
# include <openssl/evp.h>
^~~~~~~~~~~~~~~
compilation terminated.
This is caused by a complete overriding of make flags which are provided
correctly in `UBOOT_MAKE_FLAGS` variable, but currently overriden
instead of extended. This then leads to the usage of build host include
dirs, which are not available.
Fix it by extending `UBOOT_MAKE_FLAGS` variable in all device recipes.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
From Andreas Böhler:
"Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC
in contrast to the Macronix NAND with 4 bit ECC.".
Uboot needs to know this in order to have a chance to load from
the NAND.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-16
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet: 16x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J12) with populated standard pin connector on
the right back of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
We don't need to make sure that we want to have enabled
CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1].
This was actually needed only for clearfog board [2], which was added in
commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add
patch to enable setexpr for clearfog boards) and send to U-boot to fix
it properly. After a while, there was added support for Turris Omnia,
which uses setexpr as well [3], but for this board, there are no fixes
needed in U-boot and that's why we can remove this option here.
It is helpful with shell scripting. If some downstream distributions are
using it, they should correct it in defconfig for related boards.
[1] e95afa5675/cmd/Kconfig (L1504)
[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)
[3] 852126680e/target/linux/mvebu/image/turris-omnia.bootscript (L2)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Option CMD_SETEXPR is already default in U-boot [1], since this was
disabled since initial version for this board, there is send this
patch to U-boot mailing list to enable it.
It is required to use in OpenWrt bootscript for these boards [2].
[1] e95afa5675/cmd/Kconfig (L1504)
[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
There are two versions which are identical apart from the enclosure:
YunCore AX820: indoor ceiling mount AP with integrated antennas
YunCore HWAP-AX820: outdoor enclosure with external (N) connectors
Hardware specs:
SoC: MediaTek MT7621DAT
Flash: 16 MiB SPI NOR
RAM: 128MiB (DDR3, integrated)
WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
LED: Status (green)
Button: Reset
Power: 802.11af/at PoE; DC 12V,1A
Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external
Flash instructions:
The "OpenWRT support" version of the AX820 comes with a LEDE-based
firmware with proprietary MTK drivers and a luci webinterface and
ssh accessible under 192.168.1.1 on LAN; user root, no password.
The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
you will have to force the upgrade due to a different factory name.
Remember: Do *not* preserve factory configuration!
MAC addresses as used by OEM firmware:
use address source
2g 44:D1:FA:*:0b Factory 0x0004 (label)
5g 46:D1:FA:*:0b LAA of 2g
lan 44:D1:FA:*:0c Factory 0xe000
wan 44:D1:FA:*:0d Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.
Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Replace pending patch with version accepted upstream.
Other than in the first suggested version, the new property is now
called 'u-boot,bootconf' instead of 'bootconf'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove '0x' prefix from pstore node in dts, just like it was done
for the device tree used by Linux on MT7622.
This change is done in preparation to update U-Boot to 2022.04.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HP v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 24 ethernet port PoE status LEDs
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
* Management MCU: ST Micro ST32F100 Microcontroller
* 6 BCM59111 PSE chips
* 170W power budget
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a TI or SIPEX 3232C for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access
points based on the Qualcomm QCA9558 SoC. They share PCB designs with
several devices that already have partial or full support, most notably the
Devolo DVL1750i/e.
The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however
the 55 models' ART does not contain calibration data for their third chain
despite it being present on the PCB.
Specifications common to all models:
- Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor)
- 128 MB RAM
- 16 MB SPI flash
- 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in
- Green and Red status LEDs sharing a single external light-pipe
- Reset button on PCB[1]
- Piezo beeper on PCB[2]
- Serial UART header on PCB
- Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC
Unique to AP100 and AP100C:
- 3T3R 2.4GHz 802.11b/g/n via SoC WMAC
- 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP55 and AP55C:
- 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
- 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP100 and AP55:
- External RJ45 serial console port[3]
- USB 2.0 Type A port, power controlled via GPIO 11
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
MAC addresses as verified by OEM firmware:
use address source
LAN label config 0x201a (label)
2g label + 1 art 0x1002 (also found at config 0x2004)
5g label + 9 art 0x5006
Increments confirmed across three AP55C, two AP55, and one AP100C.
These changes have been tested to function on both current master and
21.02.0 without any obvious issues.
[1] Button is present but does not alter state of any GPIO on SoC
[2] Buzzer and driver circuitry is present on PCB but is not connected to
any GPIO. Shorting an unpopulated resistor next to the driver circuitry
should connect the buzzer to GPIO 4, but this is unconfirmed.
[3] This external RJ45 serial port is disabled in the OEM firmware, but
works in OpenWRT without additional configuration, at least on my
three test units.
[4] On AP100/AP55 models the UART header is accessible after removing
the device's top cover. On AP100C/AP55C models, the PCB must be removed
for access; three screws secure it to the case.
Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX
Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.
Specifications:
- SoC: MediaTek MT7621
- Flash: 32 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
Non-programmable "Power" LED
- Buttons: Reset and WPS
Instalation:
Install from TFTP
Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name
You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8
There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.
Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
Specification:
- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Specification:
- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
As anyway only the default is called now we can as well also just remove
the override for Build/Configure.
Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Two patches were removed because of the changes introduced in upstream:
1. 110-mx6cuboxi-mmc-fallback.patch
Looks like similar changes were introduced in 6c3fbf3e456c ("mx6cuboxi:
customize board_boot_order to access eMMC").
2. 111-mx6cuboxi_defconfig-force-mmc-boot.patch
The 'CONFIG_SPL_FORCE_MMC_BOOT' was removed in 15aec318ef03 ("Revert
"imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon
mode").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Store selected boot configuration in '/chosen' node in device tree, so
it can be accessed by Linux (and used for fine-tuning the FIT partition
parser).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks.
Correctly set that in uboot-envtools as well to allow writing to the
bootloader environment using fw_setenv.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2022.01 has a regression that broke eMMC usage on most if not all Armada
SoC-s, thus breaking boards like uDPU which use eMMC for storage.
Fix it by backporting a recent upstream patch.
Fixes: 782d4c8306 ("uboot-mvebu: update to version 2022.01")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24 v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a SIPEX 3232EC for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
This patch adds the device-specific configuration to u-boot-envtools for
I-O DATA BSH-G24MB switch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add U-Boot environment settings for Ruijie RG-EW3200GX PRO to allow
users to access the bootloader environment using fw_printenv/fw_setenv
while running OpenWrt.
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Steps to reproduce:
1. Insert NVMe disk with a reduction to Turris Omnia
2. Go to U-boot
3. Run these two commands:
a) ``nvme scan``
b) ``nvme detail``
4. Wait for crash
This is backported from U-boot upstream repository.
It should be included in the upcoming release - 2022.04 [1].
It was tested on Turris Omnia, mvebu, cortex-a9, OpenWrt master.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20211209100639.21530-1-pali@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[Export the patch from U-Boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ZTE MF286A and MF286R are indoor LTE category 6/7 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.
Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN:
[MF286A] MDM9230-based category 6 internal LTE modem
[MF286R] PXA1826-based category 7 internal LTE modem
in extended mini-PCIE form factor, with 3 internal antennas and
2 external antenna connections, single mini-SIM slot.
- FXS: one external ATA port (handled entirely by modem part) with two
physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
Signal state) handled entirely by modem. 4 link status LEDs handled by
the switch on the backside.
- Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and
monitoring handled by modem.
- Label MAC device: eth0
The device shares many components with previous model, MF286, differing
mostly by a Wave2 5GHz radio, flash layout and internal LED color.
In case of MF286A, the modem is the same as in MF286. MF286R uses a
different modem based on Marvell PXA1826 chip.
Internal modem of MF286A is supported via uqmi, MF286R modem isn't fully
supported, but it is expected to use comgt-ncm for connection, as it
uses standard 3GPP AT commands for connection establishment.
Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.
Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.
STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
version before installation, to have built-in modem at the latest firmware
version.
STEP 1: gaining root shell:
Method 1:
This works if busybox has telnetd compiled in the binary.
If this does not work, try method 2.
Using well-known exploit to start telnetd on your router - works
only if Busybox on stock firmware has telnetd included:
- Open stock firmware web interface
- Navigate to "URL filtering" section by going to "Advanced settings",
then "Firewall" and finally "URL filter".
- Add an entry ending with "&&telnetd&&", for example
"http://hostname/&&telnetd&&".
- telnetd will immediately listen on port 4719.
- After connecting to telnetd use "admin/admin" as credentials.
Method 2:
This works if busybox does not have telnetd compiled in. Notably, this
is the case in DNA.fi firmware.
If this does not work, try method 3.
- Set IP of your computer to 192.168.0.22. (or appropriate subnet if
changed)
- Have a TFTP server running at that address
- Download MIPS build of busybox including telnetd, for example from:
https://busybox.net/downloads/binaries/1.21.1/busybox-mips
and put it in it's root directory. Rename it as "telnetd".
- As previously, login to router's web UI and navigate to "URL
filtering"
- Using "Inspect" feature, extend "maxlength" property of the input
field named "addURLFilter", so it looks like this:
<input type="text" name="addURLFilter" id="addURLFilter" maxlength="332"
class="required form-control">
- Stay on the page - do not navigate anywhere
- Enter "http://aa&zte_debug.sh 192.168.0.22 telnetd" as a filter.
- Save the settings. This will download the telnetd binary over tftp and
execute it. You should be able to log in at port 23, using
"admin/admin" as credentials.
Method 3:
If the above doesn't work, use the serial console - it exposes root shell
directly without need for login. Some stock firmwares, notably one from
finnish DNA operator lack telnetd in their builds.
STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.
It is highly recommended to perform backup using both methods, to avoid
hassle of reassembling firmware images in future, if a restore is
needed.
Method 1: after booting OpenWrt initramfs image via TFTP:
PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION.
- Dump stock firmware located on stock kernel and ubi partitions:
ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
ssh root@192.168.1.1: cat /dev/mtd9 > mtd9_ubi.bin
And keep them in a safe place, should a restore be needed in future.
Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:
cat /proc/mtd
It should show the following:
mtd0: 000a0000 00010000 "u-boot"
mtd1: 00020000 00010000 "u-boot-env"
mtd2: 00140000 00010000 "reserved1"
mtd3: 000a0000 00020000 "fota-flag"
mtd4: 00080000 00020000 "art"
mtd5: 00080000 00020000 "mac"
mtd6: 000c0000 00020000 "reserved2"
mtd7: 00400000 00020000 "cfg-param"
mtd8: 00400000 00020000 "log"
mtd9: 000a0000 00020000 "oops"
mtd10: 00500000 00020000 "reserved3"
mtd11: 00800000 00020000 "web"
mtd12: 00300000 00020000 "kernel"
mtd13: 01a00000 00020000 "rootfs"
mtd14: 01900000 00020000 "data"
mtd15: 03200000 00020000 "fota"
mtd16: 01d00000 00020000 "firmware"
Differences might indicate that this is NOT a MF286A device but
one of other variants.
- Copy over all MTD partitions, for example by executing the following:
for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \
/var/usb_disk/mtd$i; done
"Firmware" partition can be skipped, it is a concatenation
of "kernel" and "rootfs".
- If the count of MTD partitions is different, this might indicate that
this is not a MF286A device, but one of its other variants.
- (optionally) rename the files according to MTD partition names from
/proc/mtd
- Unmount the filesystem:
umount /var/usb_disk; sync
and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
firmware. This is especially important, because stock firmware for
this device is not available officially, and is usually customized by
the mobile providers.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.0.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.0.22
setenv ipaddr 192.168.0.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
Method 2: using initramfs image as temporary boot kernel
This exploits the fact, that kernel and rootfs MTD devices are
consecutive on NAND flash, so from within stock image, an initramfs can
be written to this area and booted by U-boot on next reboot, because it
uses "nboot" command which isn't limited by kernel partition size.
- Download the initramfs-kernel.bin image
- After backing up the previous MTD contents, write the images to the
"firmware" MTD device, which conveniently concatenates "kernel" and
"rootfs" partitions that can fit the initramfs image:
nandwrite -p /dev/<firmware-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286a-initramfs-kernel.bin
- If write is OK, reboot the device, it will reboot to OpenWrt
initramfs:
reboot -f
- After rebooting, SSH into the device and use sysupgrade to perform
proper installation.
Method 3: using built-in TFTP recovery (LAST RESORT):
- With that method, ensure you have complete backup of system's NAND
flash first. It involves deliberately erasing the kernel.
- Download "-initramfs-kernel.bin" image for the device.
- Prepare the recovery image by prepending 8MB of zeroes to the image,
and name it root_uImage:
dd if=/dev/zero of=padding.bin bs=8M count=1
cat padding.bin openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin >
root_uImage
- Set up a TFTP server at 192.0.0.1/8. Router will use random address
from that range.
- Put the previously generated "root_uImage" into TFTP server root
directory.
- Deliberately erase "kernel" partition" using stock firmware after
taking backup. THIS IS POINT OF NO RETURN.
- Restart the device. U-boot will attempt flashing the recovery
initramfs image, which will let you perform actual installation using
sysupgrade. This might take a considerable time, sometimes the router
doesn't establish Ethernet link properly right after booting. Be
patient.
- After U-boot finishes flashing, the LEDs of switch ports will all
light up. At this moment, perform power-on reset, and wait for OpenWrt
initramfs to finish booting. Then proceed to actual installation.
STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
STEP 5: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth '<auth>' # As required, usually 'none'
option pincode '<pin>' # If required by SIM
option apn '<apn>' # As required by ISP
option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'
For example, the following works for most polish ISPs
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth 'none'
option apn 'internet'
option pdptype 'ipv4'
The required minimum is:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
In this case, the modem will use last configured APN from stock
firmware - this should work out of the box, unless your SIM requires
PIN which can't be switched off.
If you have build with LuCI, installing luci-proto-qmi helps with this
task.
Restoring the stock firmware:
Preparation:
If you took your backup using stock firmware, you will need to
reassemble the partitions into images to be restored onto the flash. The
layout might differ from ISP to ISP, this example is based on generic stock
firmware
The only partitions you really care about are "web", "kernel", and
"rootfs". These are required to restore the stock firmware through
factory TFTP recovery.
Because kernel partition was enlarged, compared to stock
firmware, the kernel and rootfs MTDs don't align anymore, and you need
to carve out required data if you only have backup from stock FW:
- Prepare kernel image
cat mtd12_kernel.bin mtd13_rootfs.bin > owrt_kernel.bin
truncate -s 4M owrt_kernel_restore.bin
- Cut off first 1MB from rootfs
dd if=mtd13_rootfs.bin of=owrt_rootfs.bin bs=1M skip=1
- Prepare image to write to "ubi" meta-partition:
cat mtd6_reserved2.bi mtd7_cfg-param.bin mtd8_log.bin mtd9_oops.bin \
mtd10_reserved3.bin mtd11_web.bin owrt_rootfs.bin > \
owrt_ubi_ubi_restore.bin
You can skip the "fota" partition altogether,
it is used only for stock firmware update purposes and can be overwritten
safely anyway. The same is true for "data" partition which on my device
was found to be unused at all. Restoring mtd5_cfg-param.bin will restore
the stock firmware configuration you had before.
Method 1: Using initramfs:
This method is recmmended if you took your backup from within OpenWrt
initramfs, as the reassembly is not needed.
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Look up the kernel and ubi partitions in /proc/mtd
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
(scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
mtd write <kernel_mtd> mtd4_kernel.bin
rm mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
restore them individually. Otherwise you might run out of space in
tmpfs:
(scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin
rm mtd3_ubiconcat0.bin
(scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin
rm mtd5_ubiconcat1.bin
- If the write was correct, force a device reboot with
reboot -f
Method 2: Using live OpenWrt system (NOT RECOMMENDED):
- Prepare a USB flash drive contatining MTD backup files
- Ensure you have kmod-usb-storage and filesystem driver installed for
your drive
- Mount your flash drive
mkdir /tmp/usb
mount /dev/sda1 /tmp/usb
- Remount your UBI volume at /overlay to R/O
mount -o remount,ro /overlay
- Write back the kernel and ubi partitions from USB drive
cd /tmp/usb
mtd write mtd4_kernel.bin /dev/<kernel_mtd>
mtd write mtd9_ubi.bin /dev/<kernel_ubi>
- If everything went well, force a device reboot with
reboot -f
Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota"
MTD partition which may be safely erased after reboot anyway.
Method 3: using built-in TFTP recovery:
This method is recommended if you took backups using stock firmware.
- Assemble a recovery rootfs image from backup of stock partitions by
concatenating "web", "kernel", "rootfs" images dumped from the device,
as "root_uImage"
- Use it in place of "root_uImage" recovery initramfs image as in the
TFTP pre-installation method.
Quirks and known issuesa
- It was observed, that CH340-based USB-UART converters output garbage
during U-boot phase of system boot. At least CP2102 is known to work
properly.
- Kernel partition size is increased to 4MB compared to stock 3MB, to
accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
image is at 2.5MB which is dangerously close to the limit. This has no
effect on booting the system - but keep that in mind when reassembling
an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
you used before in stock firmware first. If you need to change it,
please use protocok '3g' to establish connection once, or use the
following command to change APN (and optionally IP type) manually:
echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the blue debug LED hidden
inside the case. All other LEDs are controlled by modem, on which the
router part has some influence only on Wi-Fi LED.
- Wi-Fi LED currently doesn't work while under OpenWrt, despite having
correct GPIO mapping. All other LEDs are controlled by modem,
including this one in stock firmware. GPIO19, mapped there only acts
as a gate, while the actual signal source seems to be 5GHz Wi-Fi
radio, however it seems it is not the LED exposed by ath10k as
ath10k-phy0.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
reset of whole board, not only the modem. It is attached to
gpio-restart driver, to restart the modem on reboot as well, to ensure
QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
for OpenWrt operation at all - have fun lurking around.
The same modem module is used as in older MF286.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Previously, grub2 was hardcoded to always look on "hd0" for the
kernel.
This works well when the system only had a single disk.
But if there was a second disk/stick present, it may have look
on the wrong drive because of enumeration races.
This patch utilizes grub2 search function to look for a filesystem
with the label "kernel". This works thanks to existing setup in
scripts/gen_image_generic.sh. Which sets the "kernel" label on
both the fat and ext4 filesystem variants.
Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com>
Suggested-by: Alberto Bursi <bobafetthotmail@gmail.com> (MX100 WA)
(word wrapped, slightly rewritten commit message, removed MX100 WA)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AT91Bootstrap version 4 is available only for SAM9X60, SAMA5D2, SAMA5D3,
SAMA5D4, SAMA7G5. Thus use v4.0.1 for the above targets and v3.10.4 for
the rest of them. With the switch to v4 AT91Bootstrap binaries are now
on build/binaries. Take also this into account. Also, patches directory
is not needed anymore with the version update.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
100-ddr-marvell-a38x-fix-BYTE_HOMOGENEOUS_SPLIT_OUT-deci.patch [1]:
SoC Marvell A38x is used in Turris Omnia, and we thought that with recent
fiddling around DDR training to fix it once for all, there were
reproduced the issue in the upcoming new revision Turris Omnia boards.
101-arm-mvebu-spl-Add-option-to-reset-the-board-on-DDR-t.patch [2]:
This is useful when some board may occasionally fail with DDR training,
and it adds the option to reset the board on the DDR training failure
102-arm-mvebu-turris_omnia-Reset-the-board-immediately-o.patch [3]:
This enables the option CONFIG_DDR_RESET_ON_TRAINING_FAILURE (added by
101 patch), so the Turris Omnia board is restarted immediately, and it
does not require to reset the board manually or wait 120s for MCU to
reset the board
[1] https://patchwork.ozlabs.org/project/uboot/patch/20220217000837.13003-1-kabel@kernel.org/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-1-kabel@kernel.org/
[3] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-2-kabel@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too
large upon decompression (>7MB or so) to decompress itself on boot (see
FS#4110[1]).
There have been many attempts to fix booting from a compressed kernel on
the HiveAP-330:
- b683f1c36d ("mpc85xx: Use gzip compressed kernel on HiveAP-330")
- 98089bb8ba ("mpc85xx: Use uncompressed kernel on the HiveAP-330")
- 26cb167a5c ("mpc85xx: Fix Aerohive HiveAP-330 initramfs image")
We can no longer compress the kernel due to size, and the stock bootloader
does not support any other types of compression. Since an uncompressed
kernel no longer fits in the 8MiB kernel partition at 0x2840000, we need to
patch u-boot to autoboot by running variable which isn't set by the
bootloader on each autoboot.
This commit repartitions the HiveAP, requiring a new COMPAT_VERSION,
and uses the DEVICE_COMPAT_MESSAGE to guide the user to patch u-boot,
which changes the variable run on boot to be `owrt_boot`; the user can
then set the value of that variable appropriately.
The following has been documented in the device's OpenWrt wiki page:
<https://openwrt.org/toh/aerohive/hiveap-330>. Please look there
first/too for more information.
The from-stock and upgrade from a previous installation now becomes:
0) setup a network with a dhcp server and a tftp server at serverip
(192.168.1.101) with the initramfs image in the servers root directory.
1) Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted. If the password
doesn't work. Try reseting the device by pressing and holding the reset
button with the stock OS.
2) Once in U-Boot, set the new owrt_boot and tftp+boot the initramfs image:
Use copy and paste!
# fw_setenv owrt_boot 'setenv bootargs \"console=ttyS0,$baudrate\";bootm 0xEC040000 - 0xEC000000'
# save
# dhcp
# setenv bootargs console=ttyS0,$baudrate
# tftpboot 0x1000000 192.168.1.101:openwrt-mpc85xx-p1020-aerohive_hiveap-330-initramfs-kernel.bin
# bootm
3) Once openwrt booted:
carefully copy and paste this into the root shell. One step at a time
# 3.0 install kmod-mtd-rw from the internet and load it
opkg update; opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=y
# 3.1 create scripts that modifies uboot
cat <<- "EOF" > /tmp/uboot-update.sh
. /lib/functions/system.sh
cp "/dev/mtd$(find_mtd_index 'u-boot')" /tmp/uboot
cp /tmp/uboot /tmp/uboot_patched
ofs=$(strings -n80 -td < /tmp/uboot | grep '^ [0-9]* setenv bootargs.*cp\.l' | cut -f2 -d' ')
for off in $ofs; do
printf "run owrt_boot; " | dd of=/tmp/uboot_patched bs=1 seek=${off} conv=notrunc
done
md5sum /tmp/uboot*
EOF
# 3.2 run the script to do the modification
sh /tmp/uboot-update.sh
# verify that /tmp/uboot and /tmp/uboot_patched are good
#
# my uboot was: (is printed during boot)
# U-Boot 2009.11 (Jan 12 2017 - 00:27:25), Build: jenkins-HiveOS-Honolulu_AP350_Rel-245
#
# d84b45a2e8aca60d630fbd422efc6b39 /tmp/uboot
# 6dc420f24c2028b9cf7f0c62c0c7f692 /tmp/uboot_patched
# 98ebc7e7480ce9148cd2799357a844b0 /tmp/uboot-update.sh <-- just for reference
# 3.3 this produces the /tmp/u-boot_patched file.
mtd write /tmp/uboot_patched u-boot
3) scp over the sysupgrade file to /tmp/ and run sysupgrade to flash OpenWrt:
sysupgrade -n /tmp/openwrt-mpc85xx-p1020-aerohive_hiveap-330-squashfs-sysupgrade.bin
4) after the reboot, you are good to go.
Other notes:
- Note that after this sysupgrade, the AP will be unavailable for 7 minutes
to reformat flash. The tri-color LED does not blink in any way to
indicate this, though there is no risk in interrupting this process,
other than the jffs2 reformat being reset.
- Add a uci-default to fix the compat version. This will prevent updates
from previous versions without going through the installation process.
- Enable CONFIG_MTD_SPLIT_UIMAGE_FW and adjust partitioning to combine
the kernel and rootfs into a single dts partition to maximize storage
space, though in practice the kernel can grow no larger than 16MiB due
to constraints of the older mpc85xx u-boot platform.
- Because of that limit, KERNEL_SIZE has been raised to 16m.
- A .tar.gz of the u-boot source for the AP330 (a.k.a. Goldengate) can
be found here[2].
- The stock-jffs2 partition is also removed to make more space -- this
is possible only now that it is no longer split away from the rootfs.
- the console-override is gone. The device will now get the console
through the bootargs. This has the advantage that you can set a different
baudrate in uboot and the linux kernel will stick with it!
- due to the repartitioning, the partition layout and names got a makeover.
- the initramfs+fdt method is now combined into a MultiImage initramfs.
The separate fdt download is no longer needed.
- added uboot-envtools to the mpc85xx target. All targets have uboot and
this way its available in the initramfs.
[1]: https://bugs.openwrt.org/index.php?do=details&task_id=4110
[2]: magnet:?xt=urn:btih:e53b27006979afb632af5935fa0f2affaa822a59
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(rewrote parts of the commit message, Initramfs-MultiImage,
dropped bootargs-override, added wiki entry + link, uboot-envtools)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
Hardware
--------
SoC: QCN5502
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 1 gigabit port
Wireless No1: QCN5502 on-chip 2.4GHz 4x4
Wireless No2: QCA9984 pcie 5GHz 4x4
USB: none
Installation
------------
Flash the factory image using the stock web interface or TFTP the
factory image to the bootloader.
What works
----------
- LEDs
- Ethernet port
- 5GHz wifi (QCA9984 pcie)
What doesn't work
-----------------
- 2.4GHz wifi (QCN5502 on-chip)
(I was not able to make this work, probably because ath9k requires
some changes to support QCN5502.)
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
ZTE MF286 is an indoor LTE category 6 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.
Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: GD5F1G04UBYIG 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9882 2x2 MIMO 802.11ac radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN: MDM9230-based category 6 internal LTE modem in extended
mini-PCIE form factor, with 3 internal antennas and 2 external antenna
connections, single mini-SIM slot. Modem model identified as MF270,
- FXS: one external ATA port (handled entirely by modem part) with two
physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
Signal state) handled entirely by modem. 4 link status LEDs handled by
the switch on the backside.
- Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and
monitoring handled by modem.
- Label MAC device: eth0
Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.
Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.
STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
version before installation, to have built-in modem at the latest firmware
version.
STEP 1: gaining root shell:
Method 1:
This works if busybox has telnetd compiled in the binary.
If this does not work, try method 2.
Using well-known exploit to start telnetd on your router - works
only if Busybox on stock firmware has telnetd included:
- Open stock firmware web interface
- Navigate to "URL filtering" section by going to "Advanced settings",
then "Firewall" and finally "URL filter".
- Add an entry ending with "&&telnetd&&", for example
"http://hostname/&&telnetd&&".
- telnetd will immediately listen on port 4719.
- After connecting to telnetd use "admin/admin" as credentials.
Method 2:
This works if busybox does not have telnetd compiled in. Notably, this
is the case in DNA.fi firmware.
If this does not work, try method 3.
- Set IP of your computer to 192.168.1.22.
- Have a TFTP server running at that address
- Download MIPS build of busybox including telnetd, for example from:
https://busybox.net/downloads/binaries/1.21.1/busybox-mips
and put it in it's root directory. Rename it as "telnetd".
- As previously, login to router's web UI and navigate to "URL
filtering"
- Using "Inspect" feature, extend "maxlength" property of the input
field named "addURLFilter", so it looks like this:
<input type="text" name="addURLFilter" id="addURLFilter" maxlength="332"
class="required form-control">
- Stay on the page - do not navigate anywhere
- Enter "http://aa&zte_debug.sh 192.168.1.22 telnetd" as a filter.
- Save the settings. This will download the telnetd binary over tftp and
execute it. You should be able to log in at port 23, using
"admin/admin" as credentials.
Method 3:
If the above doesn't work, use the serial console - it exposes root shell
directly without need for login. Some stock firmwares, notably one from
finnish DNA operator lack telnetd in their builds.
STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.
Method 1: after booting OpenWrt initramfs image via TFTP:
PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION.
- Dump stock firmware located on stock kernel and ubi partitions:
ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
ssh root@192.168.1.1: cat /dev/mtd8 > mtd8_ubi.bin
And keep them in a safe place, should a restore be needed in future.
Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:
cat /proc/mtd
It should show the following:
mtd0: 00080000 00010000 "uboot"
mtd1: 00020000 00010000 "uboot-env"
mtd2: 00140000 00020000 "fota-flag"
mtd3: 00140000 00020000 "caldata"
mtd4: 00140000 00020000 "mac"
mtd5: 00600000 00020000 "cfg-param"
mtd6: 00140000 00020000 "oops"
mtd7: 00800000 00020000 "web"
mtd8: 00300000 00020000 "kernel"
mtd9: 01f00000 00020000 "rootfs"
mtd10: 01900000 00020000 "data"
mtd11: 03200000 00020000 "fota"
Differences might indicate that this is NOT a vanilla MF286 device but
one of its later derivatives.
- Copy over all MTD partitions, for example by executing the following:
for i in 0 1 2 3 4 5 6 7 8 9 10 11; do cat /dev/mtd$i > \
/var/usb_disk/mtd$i; done
- If the count of MTD partitions is different, this might indicate that
this is not a standard MF286 device, but one of its later derivatives.
- (optionally) rename the files according to MTD partition names from
/proc/mtd
- Unmount the filesystem:
umount /var/usb_disk; sync
and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
firmware. This is especially important, because stock firmware for
this device is not available officially, and is usually customized by
the mobile providers.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.1.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.1.22
setenv ipaddr 192.168.1.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
Method 2: using initramfs image as temporary boot kernel
This exploits the fact, that kernel and rootfs MTD devices are
consecutive on NAND flash, so from within stock image, an initramfs can
be written to this area and booted by U-boot on next reboot, because it
uses "nboot" command which isn't limited by kernel partition size.
- Download the initramfs-kernel.bin image
- Split the image into two parts on 3MB partition size boundary, which
is the size of kernel partition. Pad the output of second file to
eraseblock size:
dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
bs=128k count=24 \
of=openwrt-ath79-zte_mf286-intermediate-kernel.bin
dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
bs=128k skip=24 conv=sync \
of=openwrt-ath79-zte_mf286-intermediate-rootfs.bin
- Copy over /usr/bin/flash_eraseall and /usr/bin/nandwrite utilities to
/tmp. This is CRITICAL for installation, as erasing rootfs will cut
you off from those tools on flash!
- After backing up the previous MTD contents, write the images to the
respective MTD devices:
/tmp/flash_eraseall /dev/<kernel-mtd>
/tmp/nandwrite /dev/<kernel-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286-intermediate-kernel.bin
/tmp/flash_eraseall /dev/<kernel-mtd>
/tmp/nandwrite /dev/<rootfs-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286-intermediate-rootfs.bin
- Ensure that no bad blocks were present on the devices while writing.
If they were present, you may need to vary the split between
kernel and rootfs parts, so U-boot reads a valid uImage after skipping
the bad blocks. If it fails, you will be left with method 3 (below).
- If write is OK, reboot the device, it will reboot to OpenWrt
initramfs:
reboot -f
- After rebooting, SSH into the device and use sysupgrade to perform
proper installation.
Method 3: using built-in TFTP recovery (LAST RESORT):
- With that method, ensure you have complete backup of system's NAND
flash first. It involves deliberately erasing the kernel.
- Download "-initramfs-kernel.bin" image for the device.
- Prepare the recovery image by prepending 8MB of zeroes to the image,
and name it root_uImage:
dd if=/dev/zero of=padding.bin bs=8M count=1
cat padding.bin openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin >
root_uImage
- Set up a TFTP server at 192.0.0.1/8. Router will use random address
from that range.
- Put the previously generated "root_uImage" into TFTP server root
directory.
- Deliberately erase "kernel" partition" using stock firmware after
taking backup. THIS IS POINT OF NO RETURN.
- Restart the device. U-boot will attempt flashing the recovery
initramfs image, which will let you perform actual installation using
sysupgrade. This might take a considerable time, sometimes the router
doesn't establish Ethernet link properly right after booting. Be
patient.
- After U-boot finishes flashing, the LEDs of switch ports will all
light up. At this moment, perform power-on reset, and wait for OpenWrt
initramfs to finish booting. Then proceed to actual installation.
STEP 4: Actual installation:
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
STEP 5: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth '<auth>' # As required, usually 'none'
option pincode '<pin>' # If required by SIM
option apn '<apn>' # As required by ISP
option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'
For example, the following works for most polish ISPs
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth 'none'
option apn 'internet'
option pdptype 'ipv4'
If you have build with LuCI, installing luci-proto-qmi helps with this
task.
Restoring the stock firmware:
Preparation:
If you took your backup using stock firmware, you will need to
reassemble the partitions into images to be restored onto the flash. The
layout might differ from ISP to ISP, this example is based on generic stock
firmware.
The only partitions you really care about are "web", "kernel", and
"rootfs". For easy padding and possibly restoring configuration, you can
concatenate most of them into images written into "ubi" meta-partition
in OpenWrt. To do so, execute something like:
cat mtd5_cfg-param.bin mtd6-oops.bin mtd7-web.bin mtd9-rootfs.bin > \
mtd8-ubi_restore.bin
You can skip the "fota" partition altogether,
it is used only for stock firmware update purposes and can be overwritten
safely anyway. The same is true for "data" partition which on my device
was found to be unused at all. Restoring mtd5_cfg-param.bin will restore
the stock firmware configuration you had before.
Method 1: Using initramfs:
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Look up the kernel and ubi partitions in /proc/mtd
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
(scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
mtd write <kernel_mtd> mtd4_kernel.bin
rm mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
restore them individually. Otherwise you might run out of space in
tmpfs:
(scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin
rm mtd3_ubiconcat0.bin
(scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin
rm mtd5_ubiconcat1.bin
- If the write was correct, force a device reboot with
reboot -f
Method 2: Using live OpenWrt system (NOT RECOMMENDED):
- Prepare a USB flash drive contatining MTD backup files
- Ensure you have kmod-usb-storage and filesystem driver installed for
your drive
- Mount your flash drive
mkdir /tmp/usb
mount /dev/sda1 /tmp/usb
- Remount your UBI volume at /overlay to R/O
mount -o remount,ro /overlay
- Write back the kernel and ubi partitions from USB drive
cd /tmp/usb
mtd write mtd4_kernel.bin /dev/<kernel_mtd>
mtd write mtd8_ubi.bin /dev/<kernel_ubi>
- If everything went well, force a device reboot with
reboot -f
Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota"
MTD partition which may be safely erased after reboot anyway.
Method 3: using built-in TFTP recovery (LAST RESORT):
- Assemble a recovery rootfs image from backup of stock partitions by
concatenating "web", "kernel", "rootfs" images dumped from the device,
as "root_uImage"
- Use it in place of "root_uImage" recovery initramfs image as in the
TFTP pre-installation method.
Quirks and known issues
- Kernel partition size is increased to 4MB compared to stock 3MB, to
accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
image is at 2.5MB which is dangerously close to the limit. This has no
effect on booting the system - but keep that in mind when reassembling
an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
you used before in stock firmware first. If you need to change it,
please use protocok '3g' to establish connection once, or use the
following command to change APN (and optionally IP type) manually:
echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the green debug LED hidden
inside the case. All other LEDs are controlled by modem, on which the
router part has some influence only on Wi-Fi LED.
- Wi-Fi LED currently doesn't work while under OpenWrt, despite having
correct GPIO mapping. All other LEDs are controlled by modem,
including this one in stock firmware. GPIO19, mapped there only acts
as a gate, while the actual signal source seems to be 5GHz Wi-Fi
radio, however it seems it is not the LED exposed by ath10k as
ath10k-phy0.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
reset of whole board, not only the modem. It is attached to
gpio-restart driver, to restart the modem on reboot as well, to ensure
QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
for OpenWrt operation at all - have fun lurking around.
- MAC address shift for 5GHz Wi-Fi used in stock firmware is
0x320000000000, which is impossible to encode in the device tree, so I
took the liberty of using MAC address increment of 1 for it, to ensure
different BSSID for both Wi-Fi interfaces.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This solves issue with DDR training on Turris Omnia.
Log:
******** DRAM initialization Failed (res 0x1) ********
DDR3 Training Sequence - FAILED
ERROR ### Please RESET the board ###
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
The sizes of the ipk changed on MIPS 24Kc like this:
13281 uboot-envtools_2021.01-54_mips_24kc.ipk
13308 uboot-envtools_2022.01-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Brings bootmenu and production/recovery dual-boot scheme like on
the BPi-R2, BPi-R64, E8450 and UniFi 6 LR.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Device specifications:
======================
* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 18-24V passive POE (mode B)
+ used as WAN interface
- eth1
+ builtin switch port 4
+ used as LAN interface
* 12-24V 1A DC
* external antenna
The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ 10/100 Mbps Ethernet
+ builtin switch port 1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0
This is another MT7621 device, very similar to other Linksys EA7300
series devices.
Installation:
Upload the generated factory.bin image via the stock web firmware
updater.
Reverting to factory firmware:
Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking. Hard-resetting this device three (3) times will
put the device in failsafe (default) mode. At this point, flash the
OEM image to itself and reboot. This puts the router back into the 'B'
image and allows for a firmware upgrade.
Troubleshooting:
If the firmware will not boot, first restore the factory as described
above. This will then allow the factory.bin update to be applied
properly.
Signed-off-by: Nick McKinney <nick@ndmckinney.net>
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6282 (1.6 GHz)
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 1x USB 2.0
- 2x USB 3.0
- 2x SATA
- 3x button
- 5x leds
- serial on J5 connector accessible from rear panel
(115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)
Installation by USB + serial:
- Copy initramfs image to fat32 usb drive
- Connect pendrive to USB 2.0 front socket
- Connect serial console
- Stop booting in u-boot
- Do:
usb reset
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Installation by TFTP + serial:
- Setup TFTP server and copy initramfs image
- Connect serial console
- Stop booting in u-boot
- Do:
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Known issues:
- Power button and PHY INTn pin are connected to the same GPIO. It
causes that every network restart button is pressed in system.
As workaround, button is used as regular BTN_1.
For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The build fails when the openssl/sha.h header file is not installed on
the host system. Fix this by setting the HOSTCCFLAGS variable to the
OpenWrt HOST_CFLAGS variable, without setting this the include paths and
other modifications in the host flags done by OpenWrt will be ignored by
the build.
This fixes the following build problem:
gcc -c -D_GNU_SOURCE -D_XOPEN_SOURCE=700 -Wall -Werror -pedantic -std=c99 -O2 -I../../include/tools_share fiptool.c -o fiptool.o
In file included from fiptool.h:16,
from fiptool.c:19:
fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
19 | # include <openssl/sha.h>
| ^~~~~~~~~~~~~~~
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is based on NXP's QorIQ T2081QDS board, with a quad-core
dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5
ethernet interfaces, of which 3 are connected to the ethernet ports on
the front panel. The other 2 are internally connected to a Marvell
88E6171 switch; the other 5 ports of this switch are also connected to
the ethernet ports on the front panel.
Installation: write the sdcard image to an SD card. Stock U-Boot will
not boot, wait for it to fail then run these commands:
setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb
setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr'
saveenv
reset
The default U-Boot boot entry will now boot OpenWrt from the SD card.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Update layerscape u-boot package to LSDK-21.08 and drop patches which
are no longer needed.
The new env variable 'fsl_bootcmd_mcinitcmd_set' is needed to protect
the configured bootcmd and mc_init values. See [1] for more
informations.
[1] b62c174e86
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The configs/omap3_overo_defconfig file was removed from upstream U-Boot
in commit ed3294d6d1f9 ("arm: Remove overo board"). Remove it in OpenWrt
too. If someone needs this please add it also to upstream U-Boot.
This fixes the compile of the omap target.
Fixes: ffb807ec90 ("omap: update u-boot to 2021.07")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Follow up to commit 565b62cca2. Managed to
hit the very same issue again while playing with the NOR SPL builds.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With cryptocpp in place we can now update past the point of dropping
the old tbb_linux binary and build it instead.
Hauke confirmed that this also allows this firmware to be built on
aarch64.
97f01f5 Wtpdownloader: Properly retrieve current tty options
a33ff86 Wtpdownloader: Set CREAD tty cflag
af461d2 Wtpdownloader: Fix stuck during opening UART tty device
38c2135 Makefile: Print error when specified CLOCKSPRESET is not valid
f014428 TBB: Remove out-of-dated x86-64 ELF binary tbb_linux
1b6cb50 TBB: Fix compilation with Crypto++ 5.6.5
d9fb291 TBB: Fix memory corruptions by calling correct delete[] operator
d575885 TBB: Fix initializing CCTIM object
b9e1c4e Wtpdownloader: Fix makefile
8f61591 Wtpdownloader: Fix building with gcc 11
eabea5f TBB: Fix building with gcc 11
Signed-off-by: Andre Heider <a.heider@gmail.com>
Based on the Build Instructions for Trusted-Firmware-A [1],
there is a required cryptopp [2].
In the past, it used 'tbb_linux' image tool binary, which seems to
be buggy, deprecated and removed from A3700-utils-marvell and it should
not be used anymore. That's why I removed 001-imagetool.patch, which is
no longer necessary.
[1] https://trustedfirmware-a.readthedocs.io/en/v2.5/plat/marvell/armada/build.html
[2] https://cryptopp.com/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
without this patch a3700-utils/tim/ddr/ddr_tool.verstr contains the OpenWrt commit ID.
this patch fix the mv_ddr version commit ID by using the global variable MV_DDR_COMMIT_ID.
Upon boot it now prints "mv_ddr-devel-g02e23dbc-d DDR4 16b 1GB 1CS".
Cc: Andre Heider <a.heider@gmail.com>
Signed-off-by: Kerma Gérald <gandalf@gk2.net>
On lantiq a lot of stuff expects to be loaded to and executed at
0x80002000, including our own second stage bootloader.
For all build u-boots, the initial stack pointer is at 0x80008000. After
loading data to 0x80002000, every further stack operation corrupts the
loaded code.
Set the initial stack pointer to 0x80002000, to not overwrite code
loaded in memory. A stack of 0x2000 bytes has been proven as enough in
all done tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
On danube we only have 0x6800 bytes of usable SRAM. Everything behind
can't be written to and a SPL u-boot locks up during boot.
Since it's a hard to debug issue and took me more than two years to fix
it, I consider it worth to include fix albeit SPL u-boots are not build
in OpenWrt.
I faced the issue while trying to shrink the u-boot to 64K since some
boards only have an u-boot partition of that size from the days
ifx-uboot was used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With gcc10 the variables are placed more tightly to each other, which
uncovers a long existing bug in the lantiq DMA code. It can be observed
when using tftpboot with the filename parameter, which gets reset during
the tftpboot execution.
NetRxPackets[] points to cache line size aligned addresses. In
ltq_eth_rx_packet_align() the address NetRxPackets[] points to is
increased by LTQ_ETH_IP_ALIGN and the resulting not cache aligned
address is used further on. While doing so, the length/size is never
updated.
The "not cache aligned address" + len/size for a cache aligned address
is passed to invalidate_dcache_range(). Hence, invalidate_dcache_range()
invalidates the next 32 bit as well, which flashes the BootFile variable
as well.
variable BootFile is at address: 0x83ffe12c
NetRxPackets[] points to 0x83ffdb20 (len is 0x600)
data points to: 0x83ffdb22 (len is 0x600)
ltq_dma_dcache_inv: 0x83ffdb22 (for len 0x600)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffe120 (size: 32)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffdb40 (Bootfile: a.bin)
...
invalidate_dcache_range: 0x83ffe100 to 0x83ffe120 (Bootfile: a.bin)
invalidate_dcache_range: 0x83ffe120 to 0x83ffe140 (Bootfile: )
In ltq_dma_tx_map() and ltq_dma_rx_map() the start address passed to
ltq_dma_dcache_wb_inv() is incorrect. By considering the offset, the
start address passed to flush_dcache_range() is always aligned to 32, 64
or 128 bytes dependent on configured DMA burst size.
Fixes: FS#4113
Signed-off-by: Mathias Kresin <dev@kresin.me>
At least since gcc 7.3.0 (OpenWrt 18.06) lwr/lwl are used in the
assembly of LzmaProps_Decode. While the decission made by the compiler
looks perfect fine, it triggers some obscure hang on lantiq danube-s
v1.5 with MX29LV640EB NOR flash chips.
Only if the offset 1 is used, the hang can be observed. Using any other
offset works fine:
lwl s0,0(a1) - s0 == 0x6d000080
lwl s0,1(a1) - hangs
lwl s0,2(a1) - s0 == 0x0080xxxx
lwl s0,3(a1) - s0 == 0x80xxxxxx
It isn't clear whether it is a limitation of the flash chip, the EBU or
something else.
Force 8bit reads to prevent gcc optimizing the read with lwr/lwl
instructions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Subtarget-specific files under 'uboot-envtools' package are supported
since 6f3a05ebb0 ("uboot-envtools: support uci-default config also per
subtargets").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
This commit adds support for Xiaomi MiWiFi 3C device.
Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.
The differences are:
- Numbers of antennas (4 instead of 2). The antenna management
is done via the µC. There is no configuration needed in the
software code.
- LAN port assignments are different. LAN1 and WAN are
interchanged.
OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c
OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c
Specifications:
- CPU: MediaTek MT7628AN (575MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LED: 1x amber/blue/red. Programmable
- Button: Reset
MAC addresses as verified by OEM firmware:
use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
https://github.com/acecilia/OpenWRTInvasion
(IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0".
Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```
Limitations: For the first install the image size needs to be less
than 7733248 bits.
Thanks for all community and especially for this device:
minax007, earth08, S.Farid
Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
&wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D2 ICP board.
Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
One ETH switchport,
One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
Bluetooth module (Wi-Fi/BT), suitable for
Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
(PAC1934)
Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux
Flashing:
- follow the procedure at [2]
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Host libraries are only build static, so let's pass --static to
pkg-config globally and remove the then unnecessary patches doing
exactly that individually.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Using Host/Exports doesn't work as intended, explicitly add the
required vars so that u-boot finds the required libraries when building
its tools.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Kernel has added the different variants of the Rock Pi 4 in commit
b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a
dts"). The former Rock Pi 4 is now Rock Pi 4A.
For compatibility with kernel 5.4, this rename has been held back
so far. Having switched to kernel 5.10 now, we can finally apply
it in our tree as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
U-Boot 2021.10 has been released.
Rebase mediatek patches on top of new release and remove some patches
which have been merged upstream.
Tested on Bananapi BPi-R2 (mt7623), Bananapi BPi-R64 (mt7622) and
Linksys E8450 (mt7622).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Nobody ever updates PKG_RELEASE when changing devices or setup in
the various uboot-* packages. Use $(AUTORELEASE) so we still have
proper versioning there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Fix BPi-R2 GPIO LEDs to indicate boot into production or recovery
firmware in DTS and define them in default environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes compilation with GCC11.
Kept PKG_VERSION as there's some bug that chops off the 12 at the end.
Refreshed other patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This adds the hash also for the aarch64 toolchain in addition to the
x86_64 toolchain. This gets the build on a Linux aarch64 host one step
further.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
bump version and remove patches that have been applied
176d701 wtmi: Wait 1s after putting PHYs INTn pin low
2eeccfe wtmi: Change comment describing reset workaround
e8c94a5 wtmi: Count RAM size from both CS0 and CS1
995979e wtmi: Rename macro
e29eb29 wtmi: soc: Fix start_ap_workaround() for TF-A with debug
81245ed wtmi: Use constant name PLAT_MARVELL_MAILBOX_BASE
18ccb83 wtmi: Do a proper UART reset with clock change as described in spec
15ff106 avs: Validate VDD value from OTP
3f33626 fix: clock: a3700: change pwm clock for 600/600 and 1200/750 preset
fb5e436 wtmi: uart: fix UART baudrate divisor calculation
Signed-off-by: sean lee <ilf@live.com>
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
BananaPi BPi-R2 comes with HDMI and MIPI-DSI. Use dislpay facility in
Linux by add "console=tty1" boot argument.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes a build problem seen after binutils 2.36 is used by default.
Fixes: 3f41153b1c ("toolchain/binutils: switch to version 2.36.1 by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CZ.NIC as part of Turris project released free and open source WTMI
application firmware wtmi_app.bin for all Armada 3720 devices.
This firmware includes additional features like access to Hardware
Random Number Generator of Armada 3720 SoC which original Marvell's
fuse.bin image does not have.
Add a patch which allows to pass the commit id, so the firmware is able
to identify itself, see a04bffeb.
Add a patch to disable linking with gold, since the ARM toolchain
doesn't ship gold.
Cherry-pick the 3 post-release fixes.
Signed-off-by: Andre Heider <a.heider@gmail.com>
02e23db fix compilation errors popped up by GCC-10
7c35173 Merge pull request #29 from pali/sync-a38x-uboot
bb734f5 mv_ddr: a38x: Use SOC_REGS_PHY_BASE for INTER_REGS_BASE
ee1ea84 mv_ddr: a38x: Fix ddr3 compilation
70f3e2e mv_ddr: Fix comment typo
dd960b4 mv_ddr: ddr3: Allow boards to specify CK_DELAY parameter
a87f4f7 mv_ddr: ddr3: only use active chip-selects when tuning ODT
3defcec mv_ddr: a38x: Add support for setting timing in hws_topology_map
Signed-off-by: Andre Heider <a.heider@gmail.com>
2efdb10 wtmi: Fix calculation of UART divider
4247e39 fix: twin die ddr porting guide
8ad7992 sys_init: Add missing newlines in debug mode
4ddea19 avs: Validate VDD value from OTP
c444aeb avs: Fix description for avs value 0x2e
1915b78 tim: Optimize code generated by gettimver.sh and print newline
21f566d tim: Print mv_ddr version and configuration on UART
840b70b tim: Use variable $DDRFILE where possible
c10e6ae tim: Fix waiting for UART TX ready
7bf95cf wtmi: Wait 3ms for the TX on UART to be empty prior resetting TX FIFO
63e8433 wtmi: Add "dirty" suffix to git commit and rebuild sys_init.bin binary when VERSION changes
e949b58 wtmi: During setup clock phase print CPU and DDR speed
10376b5 wtmi: Flush output on UART after the '\n' character
509c647 Makefile: Check that specified DDR_TOPOLOGY option is valid
Signed-off-by: Andre Heider <a.heider@gmail.com>
Revert to using the checked in `tbb_linux` image tool binary since building
it drags in the rather big Crypto++ project.
Cherry-pick the post-release UART fixes.
Switch to AUTORELEASE while at it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
From version 2021.09 U-Boot will fixup Turris Omnia's DTB before
booting, separating U-Boot's environment into separate MTD partition
"u-boot-env" [1].
Check if "u-boot-env" MTD partition exists and set the uci defaults
accordingly.
[1] https://lists.denx.de/pipermail/u-boot/2021-July/455017.html
Signed-off-by: Marek Behún <marek.behun@nic.cz>
As the board name was changed to be identical to the device tree
compatible string (just like for other boards), also reflect that
change for U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add fw_env configuration for the BPi-R2 which is a mediatek/mt7623
devboard which can be booted from SD Card or eMMC.
Auto detect the boot device and add environment accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All mediatek boards having fw_env accessible through uboot-envtools
belong to be mt7622 subtarget. Move the file, as subtarget-specific
files are supported for a while now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* use built-in default environment instead of file in bootfs
* get rid of bootfs alltogether and use uImage.FIT
* auto-detect boot device like original script did
* add support for factory button
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ! Behavior change !
Old behavior: If the Reset button is held down during power-on
do factory reset and try booting recovery from TFTP forever.
If valid recovery is received via TFTP, write it to flash and boot.
New behavior: If the Reset button is held down during power-on
do factory reset, then try TFTP *once*, then try booting on-flash
recovery, then keep trying via TFTP forever until a valid image is
received.
Only if there is no bootable recovery stored on flash, store the
downloaded recovery. Then boot it.
* Set loadaddr to 0x48000000 in order to allow booting images larger
than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to
0x48000000 gives us 384MB on devices with 512MB RAM, which should be
more than enough as a maximum size for uImage.FIT to be loaded.
* Widely unify device-specific default environment in preparation to
auto-generate it from parameters.
* backport upstream commit fixing MBR/DOS partitioning
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Tom Wizetek (@wizetek) for testing.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
In order for the grub2 boot-related code to compile normally, we have
made many adjustments to the compilation parameters. These adjustments
are not necessary for tools-related code. We apply these parameter
adjustments only to the boot-related code.
Signed-off-by: 李国 <uxgood.org@gmail.com>
grub2 boot-related code and tools-related code may require different
compilation parameters. We split them into different variants for
compilation, so that we can accurately pass the required parameters and
avoid causing problems.
Signed-off-by: 李国 <uxgood.org@gmail.com>
The grub2 and grub2-efi packages should only contain boot-related code.
grub-bios-setup is the same as grub-editenv, they are both grub2 tools
and should be placed in a separate package.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[use AUTORELEASE and update to SPDX]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This is only cosmetic, but the next one adding a patch here would
have to do it anyway, and thus will get a smaller diff for review
now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)
At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.
Specifications:
Qualcomm IPQ8065
1 GB of RAM (DDR3)
512 MB Flash (NAND)
2x Wave 2 WiFi cards (QCA9984)
5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
1x LED (Controlled by a microcontroller that switches it between red and
blue with different patterns)
1x USB 3.0 Type-A
12V DC Power Input
UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
Port settings are 115200n8
More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830https://deviwiki.com/wiki/Askey_RAC2V1K
To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.
Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.
How to install:
Method 1: Install without opening the case using SSH and tftp
You'll need:
RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
initramfs and sysupgrade images
Connect to one of the router's LAN ports
Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)
After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
fw_setenv bootdelay 8
fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"
Don't reboot the router yet.
Install and set up a tftp server on your computer
Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)
Rename the initramfs image to initramfs.bin, and host it with the tftp
server
Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
After openwrt boots, ssh into it and run these commands:
fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
fw_setenv bootdelay 2
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)
You'll need:
initramfs and sysupgrade images
Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case
Install and set up a tftp server
Set a static ip on the ethernet interface of your computer
Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server
Connect the wan port of the router to your computer
Interrupt U-Boot and run these commands:
setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"
saveenv
tftpboot initramfs.bin
bootm
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2 and EA7500 v2.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Leon Poon (@LeonPoon) for the initial bringup.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
[add missing entry in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips. The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.
Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART: through-hole on PCB.
J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
pin3=GND, pin4=TX. Settings: 57600/8N1.
Note regarding dual system partitions
-------------------------------------
The vendor firmware and boot loader use a dual partition scheme. The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.
OpenWrt does not support this scheme and will always use the first OS
partition. It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.
Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used. We first flash an initramfs image, then
follow with a regular sysupgrade.
Installation:
Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
(Alternatively, you can use the TFTP recovery method below.)
You can use WiFi or Ethernet.
The direct URL is: http://192.168.3.1/07_06_00_firmware.html
a. No login is needed, and you'll be in their setup wizard.
b. You might get a warning about not being connected to the Internet.
c. Towards the bottom of the page will be a section entitled "Or
Manually Upgrade Firmware from a File:" where you can manually choose
and upload a firmware file.
d: Click "Choose File", select the OpenWRT "initramfs" image and click
"Upload."
2) The Router will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image. Note:
you may use the sysupgrade command line tool in lieu of the UI if
you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
of OpenWRT. Start by configuring a computer as a TFTP client:
a. Install a TFTP client (server not necessary)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
connecting the power.
b. As soon as the LED lights up green (roughly 2-3 seconds), release
the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image. Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Backup the OEM Firmware:
-----------------------
There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.
The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem"). We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.
1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
2) Under "Save mtdblock contents," first select "firmware" and click
"Save mtdblock" to download the image.
3) Repeat the process, but select "oem" from the pull-down menu.
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow the TFTP recovery steps for the Extender, and use the
backup image.
* OpenWrt "Flash Firmware" interface:
Upload the backup image and select "Force update"
before continuing.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8031 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This patch fixes a recently found problem when a zImage passed to
kexec-tools contains an appended DTB. In that case kexec boot fails because
the decompressor wrongly tries to use the non-existing appended DTB instaed
of the one passed in the register r2.
- http://lists.infradead.org/pipermail/kexec/2021-April/022353.html
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Florian Ekert reported:
"I have build a fresh master branch recently, Since your last change [1]
on grub2, I have now a new dependency on liblzma for the install package
grub2-editenv.
root@st-dev-07 /usr/lib # ldd /root/grub-editenv
/lib/ld-musl-x86_64.so.1 (0x7f684b088000)
liblzma.so.5 => /usr/lib/liblzma.so.5 (0x7f684b06d000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7f684b059000)
libc.so => /lib/ld-musl-x86_64.so.1 (0x7f684b088000)
This was not the case before your update.
root@st-dev-07 /usr/sbin # ldd /usr/sbin/grub-editenv
/lib/ld-musl-x86_64.so.1 (0x7fd970176000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7fd970162000)
libc.so => /lib/ld-musl-x86_64.so.1 (0x7fd970176000)
My build complains that it cannot satisfy the runtime package dependency
for grub2-editenv.
install -d -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin
install -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/grub-editenv /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin/
find /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv -name 'CVS' -o -name '.svn' -o -name '.#*' -o -name '*~'| xargs -r rm -rf
Package grub2-editenv is missing dependencies for the following libraries:
liblzma.so.5
make[2]: *** [Makefile:166: /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/bin/APOS/feckert/master/master-Maggie-455-ga5edc0e8e/x86_64/targets/x86/64/packages/grub2-editenv_2.06~rc1-1_x86_64.ipk] Error 1
make[2]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/package/boot/grub2'
time: package/boot/grub2/pc/compile#78.64#9.79#83.88
ERROR: package/boot/grub2 failed to build (build variant: pc).
make[1]: *** [package/Makefile:116: package/boot/grub2/compile] Error 1
make[1]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt'
make: *** [/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/include/toplevel.mk:230: package/boot/grub2/compile] Error 2
If I add the following changes to the package all works as expected.
<snip>
- DEPENDS:=@TARGET_x86
+ DEPENDS:=@TARGET_x86 +liblzma
VARIANT:=pc
endef
This is a hotfix but I dont´t think this is the final solution, because lzma is provided by the package xz.
And This is maintained in the package feed [not the core]"
Dirk stated & offered his patch to disable liblzma and thus resolve the
'out of core dependency' problem:
"LZMA is used in mkimage.c
disabling it prints
Without liblzma (no support for XZ-compressed mips images) (explicitly disabled)
(see configure.ac)
liblzma is autodetected so this issue was present but hidden somehow
[unsure: grep/image generation does not use grub with that option]
OpenWrt does not use that feature currently
[!] some scripts and examples use --compression=xz or -C xz and those will break
grub has an internal xzlib for different "lzma" functionality
(ext. LIBLZMA from XZ (GRUB_COMPRESSION_XZ) vs. GRUB_COMPRESSION_LZMA)"
Hopefully fixes e74d81ece2 and doesn't
break anything else.
Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
[include Florian's description of how problem 1st encountered]
[bump package release]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The current version of 'uboot-envtools' package generates dedicated
uci-default file only per target. This change makes it possible to
use subtarget-specific files, with name pattern: 'target_subtarget'
(example: 'ath79_nand'). The subtarget-specific files will take
precedence over target-specific one.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b
Specifications:
- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging
Flashing instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.
Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When building GRUB with binutils 2.35.2 or later, an error occurs due to
a section .note.gnu.property that is placed at an offset such that
objcopy needs to pad the img file with zeros. This in turn causes the
following error: "error: Decompressor is too big.".
The fix accepted by upstream patches a python script that isn't executed
at all when building GRUB with OpenWrt buildroot. There's another patch
that patches the files generated by that python script directly, but by
including it we would deviate further from upstream. Instead of doing
that, simply bump to the latest release candidate.
As one of the fixes for the CVEs causes grub to crash on some x86
hardware using legacy BIOS when compiled with -O2, filter -O2 and
-O3 out of TARGET_CFLAGS.
Fixes the following CVEs:
- CVE-2020-14372
- CVE-2020-25632
- CVE-2020-25647
- CVE-2020-27749
- CVE-2020-27779
- CVE-2021-3418
- CVE-2021-20225
- CVE-2021-20233
Runtime-tested on x86/64.
Fixes: FS#3790
Suggested-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Add support for pstore/ramoops now that DRAM content is preserved
over reboot on MT7622. On each boot, check pstore and boot to recovery
image in case there are records stored in it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
