The Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301) has two Ethernet ports,
labeled MAIN and SECONDARY, connected to gmac2 and gmac1, respectively.
The standard probe order results in gmac1/SECONDARY being eth0 and
gmac2/MAIN being eth1. This does not match the stock firmware, is
contrary to user expectation, causes the wrong (high) MAC address to be
used in a bridged configuration (the default for this device), and makes
the gmac2/MAIN port unusable in the preinit environment (such as for
failsafe). Until a recent patch, gmac1/SECONDARY (eth0) was not even
usable.
This reorders the ports so that gmac2/MAIN is eth0, and the now-working
gmac1/SECONDARY is eth1. eth0 has the low MAC address and eth1 has the
high; when bridged, the bridge takes on the correct low MAC address.
This matches the stock firmware. The MAIN port is usable for failsafe
during preinit.
This device does not have a switch on board, so there's no possibility
to remap ports via switch configuration. "ip link set $interface name"
is used instead, during preinit before networking is configured.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
Unlike many ipq806x devices, Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301)
has no switch on board. Its two Ethernet ports are connected to Atheros
AR8033 PHYs. It is not appropriate to use fixed-link in this
configuration. Instead, configure the correct PHYs in the device tree
configuration to allow the at803x driver to load.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
On a Ubiquiti UniFi AC HD (ubnt,unifi-ac-hd, UAP-AC-HD, UAP301), a
forced speed on gmac1 is set in the QSGMII PCS_ALL_CH_CTL register,
presumably by the bootloader (4.3.28), preventing the interface from
being usable. The QSDK NSS GMAC driver takes care to clear the forced
speed in nss_gmac_qsgmii_dev_init
(https://source.codeaurora.org/quic/qsdk/oss/lklm/nss-gmac/tree/ipq806x/nss_gmac_init.c?h=nss
at d5bb14925861).
gmac1 is connected to the port on the device labeled SECONDARY, and is
currently eth0 but will be switched to eth1 by a subsequent patch. By
clearing the QSGMII PCS forced speed during dwmac initialization when
SGMII is in use, this port becomes usable.
This patch is upstreamable, and will be sent upstream after successful
testing in OpenWrt.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
The stock firmware does not accept firmware with "Talon" in the name.
Tested on firmware version 1.0.10 Build 20160902 rel. 57400 which came
preinstalled, as well as latest firmware version 2.0.1 Build 20170103
rel.71053 flashed from
AD7200v1-up-ver2-0-1-P1[20170103-rel71053]_2017-01-04_10.08.28.bin.
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
[added details about vendor firmware]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Users of devices with large block storage may choose to have an LVM
partition on the same device which is used for booting OpenWrt.
The presents a problem during sysupgrade as the root device is then
still busy and changing partitions will not work as desired,
leading to data corruption in case the newly flashed image is larger
than the currently installed one.
Having loop devices setup causes similar havoc.
Make sure all volume groups are offline and all loop devices have been
released before sysupgrade.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes issue with merged DNS requests in 2.83/2.84 not being
retried on the firsts failed request causing lookup failures.
Also fixes the following security problem in dnsmasq:
* CVE-2021-3448:
If specifiying the source address or interface to be used
when contacting upstream name servers such as:
server=8.8.8.8@1.2.3.4, server=8.8.8.8@1.2.3.4#66 and
server=8.8.8.8@eth0 then all would use the same socket
bound to the explicitly configured port. Now only
server=8.8.8.8@1.2.3.4#66 will use the explicitly
configured port and the others random source ports.
Remove upstreamed patches and update remaining patch.
Signed-off-by: Alan Swanson <reiver@improbability.net>
[refreshed old runtime support patch]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This package depends on the lantiq target and is only build for that
target. A normal package would be build by the SDK builder probably
under a different target and then this package will not be selected.
Mark it as nonshared to build it when the lantiq target gets build.
Fixes: FS#3773, FS#3774
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports a fix for the low priority CVE-2021-28831:
decompress_gunzip.c in BusyBox through 1.32.1 mishandles the error bit
on the huft_build result pointer, with a resultant invalid free or
segmentation fault, via malformed gzip data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel image is too big now and the build fails.
WARNING: Image file zyxel_nbg6716-kernel.bin is too big: 4205404 > 4194304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In order to allow easily updating the bootloader on eMMC also provide
artifacts for that. Support for updating bootloader via TFTP will be
added to the loader CLI menu in a follow-up commit.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is possible to select CONFIG_MTD_PARSER_TRX on the mediatek now. Add
this option to the kernel configuration file.
Fixes: 58c5e25664 ("mediatek: support non standard trx magic values")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This partly reverts commit 20a924d2ae.
This commit broke the build of the Mediatek target with kernel 5.4, for
kernel 5.10 it is fine.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3f5080aedd nptl: Do not build nptl/tst-pthread-gdb-attach as PIE
36783141cf nptl: Check for compatible GDB in nptl/tst-pthread-gdb-attach
ea299b62e8 nptl_db: Support different libpthread/ld.so load orders (bug 27744)
162df872f0 x86: tst-cpu-features-supports.c: Update AMX check
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The spi-ath79 driver performs the chipselect by writing to dedicated
register in the SPI register block. So the GPIO numbers were not used.
Tested-on: Enterasys WS-AP3705i
Signed-off-by: David Bauer <mail@david-bauer.net>
All chipsets from AR7100 up to QCA9563 have three dedicated chipselect
lines for the integrated SPI controller. Remove the number of
chipselects from the platform data, as there is no need to manually set
this to a different value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the SPI_MASTER_GPIO_SS flag for the spi-ath79 driver. Otherwise,
the custom chipselect function is never called. This breaks hardware,
where the three dedicated chipselect lines are used instead of generic
GPIO pins.
Signed-off-by: David Bauer <mail@david-bauer.net>
This came up in an upstream commit: "
b1dd9bf688b0 "net: phy: broadcom: Fix RGMII delays for BCM50160 and BCM50610M"
The PHY driver entry for BCM50160 and BCM50610M calls
bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in
order to configuration appropriate clock delays on the PHY, fix that."
So the "rgmii" phy-mode has always been wrong, but went unnoticed since
the broadcom phy driver didn't push the delay settings to the chip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
QLCNIC_HWMON was activated when hwmon was set, but the dependency was
missing. This broke the build bot builds. Fix this by explicitly
activating HWMON support and adding a dependency.
Fixes: f88c64d28c ("kernel: netdev: add qlcnic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CLK125 output pin at the ethernet PHY is connected via capacitor to
GND and nowhere else. Disable it. Also tune the LED masks.
The MPP56 and MPP60 pins at the SoC are conected to the μPD720202 USB3.0
chip:
- MPP56: wired to PCIe CLKREQ# (out)
- MPP60: wired to PCIe RESET# (in)
Configure the pcie pinmux for these pins.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
These have long been obsolete. For reference, here's the Linux version where
each symbol has been dropped:
CONFIG_IP6_NF_QUEUE - 3.5
CONFIG_IP6_NF_TARGET_LOG - 3.4
CONFIG_IP_NF_MATCH_DSCP - 2.6.19
CONFIG_NF_CONNTRACK_IPV4 - 4.19
CONFIG_NF_CONNTRACK_IPV6 - 4.19
CONFIG_NF_CONNTRACK_RTCACHE - out-of-tree, superseded by flow offloading
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This kmod is similar to macvlan with the difference being that the
endpoints have the same mac address.
It is useful on cloud where only one mac address allowed on port,
where macvlan not works but ipvlan would.
One use case is where multiple IPs and gateways assign on one net port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new EEE patch is accepted upstream, so backport it and replace the
current one.
Cc: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
This CFI patch was accepted upstream for 5.13. Move it away from under
ath79 and place under backports to be removed in due time.
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
Since support for SFP on the MikroTik RouterBOARD 922UAGS-5HPacD was
added by 4387fe00cb, the MAC addresses for eth0 (Ethernet) and eth1
(SFP) were swapped. This patch fixes the 02_network script to assign MAC
addresses correctly, so they match the label and the vendor's OS.
Tested on a RouterBOARD 922UAGS-5HPacD board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Erase firmware ereas before writing to recovery or production partition
when updating them via the bootloader menu.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Ubiquiti Networks UniFi 6 LR access point comes with a total of
512 MB RAM provided by 2x 8-bit DDR3 SDRAM. This combination lead to
problems with the DDR calibration on boot resulting in occasional hang
on boot. Use updated calibration binary provided by MediaTek to make
boot on that device more reliable.
The binary has also been tested on the BananaPi BPi-R64 board and that
also works just fine with the new binary.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Missing braces in a macro were leading to badly working rates sometimes
getting a success probabilty of 1.0
Signed-off-by: Felix Fietkau <nbd@nbd.name>
