Commit Graph

23788 Commits

Author SHA1 Message Date
Adrian Schmutzler
a51e46e543 ramips: add Xiaomi Mi Router 4A Gigabit explicitly
This device has previously been supported by the image
for Xiaomi Mi Router 3G v2. Since this is not obvious, the
4A is marketed as a new major revision and it also seems to
have a different bootloader, this will be both more tidy and
more helpful for the users.

Apart from that, note that there also is a 100M version of
the device that uses mt7628 platform, so a specifically named
image will also prevent confusion in this area.

Specifications:

- SoC:      MediaTek MT7621
- Flash:    16 MiB NOR SPI
- RAM:      128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0:    MT7603E 2.4GHz 802.11b/g/n
- WIFI1:    MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable "power" LED (two-coloured, yellow/blue)
            Non-programmable "internet" LED (shows WAN activity)
- Buttons:  Reset

Installation:

Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".

Vendor firmware won't accept any serial input until "uart_en" is
set to "1".

Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:

To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'

Then run 'nvram commit' to make the changes permanent.

Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:

'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
  --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'

Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 17:18:26 +01:00
张鹏
448de2e2e5 ath79: add support for Qxwlan E600G v2 / E600GAC v2
E600G v2 based on Qualcomm/Atheros QCA9531

Specification:

 - 650/600/200 MHz (CPU/DDR/AHB)
 - 128/64 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz
 - 2 x 10/100 Mbps Ethernet(RJ45)
 - 1 x MiniPCI-e
 - 1 x SIM (3G/4G)
 - 5 x LED , 1 x Button(SW2-Reset Buttun), 1 x power input
 - UART(J100) header on PCB(115200 8N1)

E600GAC v2 based on Qualcomm/Atheros QCA9531 + QCA9887

Specification:

 - 650/600/200 MHz (CPU/DDR/AHB)
 - 128/64 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz
 - 1T1R 5 GHz
 - 2 x 10/100 Mbps Ethernet(RJ45)
 - 6 x LED (one three-color led), 2 x Button(SW2-Reset Buttun),1 x power input
 - UART (J100)header on PCB(115200 8N1)

Flash instruction:

1.Using tftp mode with UART connection and original OpenWrt image
 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "openwrt-ath79-generic-xxx-squashfs-sysupgrade.bin"
   to "firmware.bin" and place it in tftp server directory.
 - Connect PC with one of LAN ports, power up the router and press
   key "Enter" to access U-Boot CLI.
 - Use the following commands to update the device to OpenWrt:
   run lfw
 - After that the device will reboot and boot to OpenWrt.
 - Wait until all LEDs stops flashing and use the router.

2.Using httpd mode with Web UI connection and original OpenWrt image
 - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
 - Connect PC with one of LAN ports,press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   leds flashing.
 - Open your browser and enter 192.168.1.1,You will see the upgrade
   interface, select "openwrt-ath79-generic-xxx-squashfs-
   sysupgrade.bin" and click the upgrade button.
 - After that the device will reboot and boot to OpenWrt.
 - Wait until all LEDs stops flashing and use the router.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[rearrange in generic.mk, fix one case in 04_led_migration, update
commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 17:18:26 +01:00
Piotr Jurkiewicz
75401550c3 sunxi: fix board.d/01_leds permissions and drop include
The file lacks executable permissions, which makes it not being applied
during the first boot.

While at it, drop unneeded include.

Signed-off-by: Piotr Jurkiewicz <piotr.jerzy.jurkiewicz@gmail.com>
[do not touch board name handling, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 17:18:26 +01:00
James McGuire
de768829a5 ramips: add support for D-Link DIR-2640 A1
This patch adds support for D-Link DIR-2640 A1.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
        WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

MAC addresses:

lan   factory 0xe000     *:a7 (label)
wan   factory 0xe006     *:aa
2.4   factory 0xe000 +1  *:a8
5.0   factory 0xe000 +2  *:a9

Seems like vendor didn't replace the dummy entries in the calibration data.

Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-11 17:35:10 +01:00
Yousong Zhou
c02096361c x86: upgrade: make code comment appear as log lines
The comment content can be useful for readers of both the log and code

Previously when dd command "records in/out" messages are not filtered
like now with get_image_dd, it's not clear that these messages are for
extracting boot sectors.  E.g.

Before

  == upgrade: Reading partition table from bootdisk...
  37+26 records in
  37+26 records out
  == upgrade: Reading partition table from image...

After

  == upgrade: Reading partition table from bootdisk...
  == upgrade: Extract boot sector from the image
  37+26 records in
  37+26 records out
  == upgrade: Reading partition table from image...

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-11-11 21:29:55 +08:00
Yousong Zhou
2e34cfbca7 x86: upgrade: use get_image_dd
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140
Reported-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Reviewed-By: Philip Prindeville <philipp@redfish-solutions.com>
2020-11-11 21:29:55 +08:00
Yousong Zhou
31a34076ed x86: upgrade: use v function for writting logs
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-11-11 21:29:55 +08:00
John Audia
a47279154e kernel: bump 5.4 to 5.4.75
Manually rebased patches:
  bcm27xx:
    patches-5.4/950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
  bcm53xx:
    patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
  layerscape:
    patches-5.4/802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
    patches-5.4/808-i2c-0002-MLK-10893-i2c-imx-add-irqf_no_suspend.patch
    patches-5.4/820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch

Removed since could be reverse-applied by quilt:
  mediatek:
    patches-5.4/0700-arm-dts-mt7623-add-missing-pause-for-switchport.patch

All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64
Run-tested: ipq806x/R7800, x86_64

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64]

Rebase of 802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2020-11-10 13:11:32 +01:00
Petr Štetiar
fe302d472a rtl838x: fine tune default package set
Althought most of the switches aren't routers, they can be used as such,
so let's add some of the packages from the router's DEVICE_TYPE. While
at it, remove swconfig package which is not needed on DSA targets.

Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-09 21:50:06 +01:00
Paul Spooren
2e282537d0 imagebuilder: fix sstrip
Without an absolute path to staging_dir/host/bin/sstrip the Makefile
tries to run a host installed version of sstrip, which is likely not
available.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-09 10:54:30 +00:00
Petr Štetiar
e267445510 rtl838x: dts: use macros for phy and switch definitions
It's quite more readable, saves some tedious copy&pasting, not so
error prone etc.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-09 09:14:02 +01:00
Petr Štetiar
0516aa398c rtl838x: rtl838x.dtsi: fix missing interrupt-parent for uart0
Fixes following dtc warning:

 Warning (interrupts_property): /uart@b8002000: Missing interrupt-parent

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-09 09:14:02 +01:00
Petr Štetiar
2ab6add9b9 rtl838x: rtl838x.dtsi: remove reg property from root node
Fixes following dtc warning:

 ../dts/rtl838x.dtsi:38.3-145.3: Warning (reg_format): /: Root node has a "reg" property

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-09 09:14:02 +01:00
Petr Štetiar
b5bd945733 rtl838x: add support for D-Link DGS-1210-28
Hardware specification
 ----------------------

 * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
 * 128MB DRAM
 * 32MB NOR Flash (MX25L25635E)
 * 24 x 10/100/1000BASE-T ports
    - Internal PHY with 8 ports (RTL8218B)
    - Two external PHYs with 8 ports each (RTL8218B)
 * 4 x Gigabit RJ45/SFP Combo ports
    - External PHY with 4 SFP ports (RTL8214FC)
 * Power LED
 * Reset button on front panel
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6

 UART pinout
 -----------

  [oooo]J3 [o]ooo|J6
    |       ^ ||`------ GND
    |       | |`------- RX
    |       | `-------- TX
    |       `---------- Vcc (3V3)
    |
    `------------------ J3 is power input connector nearby J6 UART

 Boot initramfs image from U-Boot
 --------------------------------

  1. Press Escape key during `Hit Esc key to stop autoboot` prompt
  2. Press CTRL+C keys to get into real U-Boot prompt
  3. Init network with `rtk network on` command
  4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command
  5. Boot the image with `bootm` command

To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.

It has been developed and tested on device with F1 revision.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-09 09:14:02 +01:00
Petr Štetiar
aeb26f8434 rtl838x: d-link_dgs-1210: refactor common family bits
So the common bits can be easily shared with other boards in the family
and while at it add missing SPDX license identifiers into the DTS files
and fixed alphabetic sorting of the devices in the images.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-09 09:14:02 +01:00
Petr Štetiar
b1b8abaf58 rtl838x: clean whitespace issues in rtl8382_d-link_dgs-1210-16.dts
So it's tidy.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-09 09:14:02 +01:00
Roman Kuzmitskii
dd651e54cc octeon: add support for Ubiquiti EdgeRouter 4
Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router.
It has internal power supply and needs c13 power cord.
There are three 10/100/1000 Mbps RJ45/Copper ports and
one 1000 Mbps SFP port connected directly to a SoC.

SoC:
  Octeon Cavium 7130 (Cavium 3)
  Clocked at 1000Mhz

Memory:
  1 GiB (SK hynix H5TQ4G63CFR-RDC × 2)
  DDR3, clocked at 533 Mhz (1066Mhz effective)
Flash:
  - mtd:
    8 MiB (Macronix MX25L6408EMI-12G)
    used for uboot/eeprom
  - emmc:
    4 GiB (SanDisk SDIN7DP2-4G)
    used for kernel+rootfs
Leds: 1x for power status (white/blue, controllable)
  and 4x for ethernet and sfp ports (no control over them)
Buttons: 1x Reset (from SOC)
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC)
USB: 1x USB3.0 on front panel (from SoC)
MII: 1x QSGMII from SoC is used
PHY: 1x Vitesse VSC8504 of which 4x ports is used

All physical port numbers are properly mapped inside OS and
named by lanX instead of ethX.

There is also special purpose four(4) loopX ports available.
That loopX ports are currently hardcoded by linux kernel
and exact use case of them is currently unknown. We leave them
to the linux kernel and octeon board defaults.

All four (4) physical ports are connected to the same QSGMII.
vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used.

Phy mapping:
 - Phy5 is connected to physical eth0 port
 - Phy6 is connected to physical eth1 port
 - Phy7 is connected to physical eth2 port
 - Phy4 is connected to physical eth3 port

Why this device needs external dts:
 - faster boot time since need to initialize less device tree nodes.
 - to add actual indication with LED about boot/failure/upgrade.
   i.e. user could know when to enter failsafe mode or if upgrade is done
 - reset button support so user can reset their device in case off failure
 - sfp port indication in dmesg with information about sfp module
   it also indicates when module inserted or removed

Octeon quirks:
 - There is no port status available before it interface brought up
 - SFP port can not be tied to actual phy due to octeon-ethernet state
   and currently we can only get reports a about SFP state in dmesg

How to flash the firmware:
  - copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and
    openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to
    USB flash drive that is formatted to vfat/fat32
  - connect USB flash drive to edgerouter 4 front USB port
  - connect serial cable using front RJ45 port (115200 baud, 8N1)
  - connect power to cable to edgerouter 4
  - connect terminal to the console to see uboot boot process
  - interrupt boot by pressing button(s) on your keyboard to log in to the uboot
  - detect usb connected flash drives by typing to the console:
    usb start
  - after drive is detected load initramfs+kernel to the memory by typing:
    fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin
  - after initramfs+kernel is loaded to the memory load it by typing:
    bootoctlinux 0 numcores=4 endbootargs mem=0
  - boot process should finish and you will be greeted with console after pressing enter
  - create directory to mount usb flash drive to by typing:
    mkdir /tmp/sda
  - mount flash drive to that directory by typing:
    mount /dev/sda1 /tmp/sda
  - flash firmware to router internal storage by typing:
    sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar
  - device will reboot and after it gets up you will have edgerouter 4 running openwrt

Reviewed-by: Johannes Kimmel <fff@bareminimum.eu>
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
2020-11-05 19:29:48 +00:00
Roman Kuzmitskii
577ac8ce84 octeon: honor disabled sgmii device tree nodes
adds patch to octeon ethernet driver that lets sgmii interface
device tree node to be disabled and that disabled interface
won't be unnecessarily initialized.

It solves the problem with octeon boards that have 8 sgmii or more ports
initialized but have nothing connected to them.

Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
2020-11-05 19:29:48 +00:00
Roman Kuzmitskii
a8ceda752c octeon: implement interface rename by label from device tree
adds patch to octeon ethernet driver that to rename interface
name by label from device tree

Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
2020-11-05 19:29:48 +00:00
Roman Kuzmitskii
b9898cd78a generic: add support for vsc8504 phy
adds support for vsc8504 phy.
patch have use on 5.4 kernel and has
to be dropped after since phy is supported by
CONFIG_MICROSEMI_PHY on newer LTS kernels.

Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
2020-11-05 19:29:48 +00:00
David Bauer
22be18effb ath79: streamline image-generation for OCEDO boards
Use the default sysupgrade generation procedure provided
by the target. The previously generated images had the rootfs not
aligned to an eraseblock.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-05 00:00:37 +01:00
David Bauer
6f1b8c652f rockchip: remove unused config symbols
Remove MDIO and I2C bitbangig support from the kernel.

These functionalities are currently not used by any board in the target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-04 23:58:27 +01:00
David Bauer
3f05b5fda3 rockchip: fix NanoPi R2S GMAC clock name
This commit fixes the name for the GMAC clock to gmac_clkin, as this is
the name of the clock provided by the rk3328-clk driver.

Without this commit, the GMAC will not work in TX direction.

Suggested-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-04 23:58:13 +01:00
Anton Ryzhov
df469befdc ramips: fix kernel oops in mt7621_nfc_write_page_hwecc
`mt7621_nfc_write_page_hwecc` may be called with `buf=NULL`, but
`mt7621_nfc_check_empty_page` always tries to read it.
That caused Oops:
`Unable to handle kernel paging request at virtual address 00000000`

Fixes: FS#3416
Signed-off-by: Anton Ryzhov <anton@ryzhov.me>
2020-11-04 22:08:11 +08:00
Adrian Schmutzler
df9ee254aa ath79: remove redundant setup of wmac for ubnt WA devices
Several Ubiquiti WA devices set up &wmac again in their DTS files,
although this is already done in ar9342_ubnt_wa.dtsi.

Fixes: fa3c2676ab ("ath79: Add support for Ubiquiti Nanostation AC")
Fixes: cf5a1abe46 ("ath79: define 2.4GHz radio for nanostation ac loco")
Fixes: 09804da80a ("ath79: define 2.4GHz radio for litebeam ac gen2")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-03 18:34:10 +01:00
Nick Hainke
28a211808a ath79: create DTSI files for ubnt WA 1-/2-port devices
The ar9342 Ubiquiti WA devices appear to only have two different
network setups, based on the number of ethernet ports.
Create DTSI files for them to consolidate duplicate definitions.

Signed-off-by: Nick Hainke <vincent@systemli.org>
[rephrase commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-03 18:34:10 +01:00
Nick Hainke
50a76208bc ath79: fix nanobeam ac ethernet interface
In 4.14 the delays were not cleared, so setting "rgmii" as phy-mode
did not affect delays set by the bootloader. With 5.4 kernel the
situation changed and the ethernet interface stopped working.

"rgmii" requires rx and tx delays depending on the hardware circuit
and wiring. The mac or the phy can add these delays.
- "rgmii":  delays are controlled by the mac
- "rgmii-id": delays are controlled by the phy
More Information in Linux Kernel Tree:
Documentation/devicetree/bindings/net/ethernet-controller.yaml

"rgmii" should be the preferred mode, which allows the mac layer to
turn off the dealys completely if they are not needed. However, the
delays are not set correctly, which causes the ethernet interface
to be broken. Just taking the ethernetpart from the litebeam ac gen2
will fix the issue.

Explained-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2020-11-03 18:34:04 +01:00
John Crispin
f5772d71a4 rtl838x: remove the swconfig setup from the board.d code
the code currently sets up uci for swconfig which we do not use.

Signed-off-by: John Crispin <john@phrozen.org>
2020-11-03 17:46:40 +01:00
Adrian Schmutzler
54fad3f32b kernel: add disabled CONFIG_IP6_NF_TARGET_MASQUERADE
In kernel commit adf82accc5f5 ("netfilter: x_tables: merge ip and
ipv6 masquerade modules") the config symbols IP_NF_TARGET_MASQUERADE
and IP6_NF_TARGET_MASQUERADE have been demoted to simple backwards-
compat options for NETFILTER_XT_TARGET_MASQUERADE.

In netfilter.mk, this has already been updated in OpenWrt commit
d1592306cc ("netfilter.mk: use CONFIG_NETFILTER_XT_TARGET_MASQUERADE"),
having us use the new config symbol.

However, enabling IP_NF_NAT or IP6_NF_NAT still makes the relevant
legacy options selectable, so we need to disable them in generic
config (and forget about them afterwards).
Since CONFIG_IP_NF_TARGET_MASQUERADE is already present there, this
just adds the missing CONFIG_IP6_NF_TARGET_MASQUERADE.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-02 18:14:20 +01:00
Adrian Schmutzler
89a2a6c870 kernel: drop obsolete symbol CONFIG_NF_NAT_IPV6
Kernel has removed the symbols CONFIG_NF_NAT_IPV4 and
CONFIG_NF_NAT_IPV6 in favor of CONFIG_NF_NAT in commit
3bf195ae6037 ("netfilter: nat: merge nf_nat_ipv4,6 into nat core").

This drops the obsolete symbol CONFIG_NF_NAT_IPV6 from generic
config-5.4.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-02 17:27:05 +01:00
Lech Perczak
52d3b027ec ath79: ubnt-unifi: make u-boot-env partition read-only
This partition isn't normally modified during boot process. Make it
read-only to prevent accidental overwrite.
If needed this can be overriden with installing kmod-mtd-rw; the same
way as for installing modified U-boot.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2020-11-02 16:33:25 +01:00
Lech Perczak
7d93473eff ath79: ubnt-xm: make u-boot-env partition read-only
This partition isn't normally modified during boot process. Make it
read-only to prevent accidental overwrite.
If needed this can be overriden with installing kmod-mtd-rw; the same
way as for installing modified U-boot.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2020-11-02 16:33:25 +01:00
John Audia
71b2b32f98 kernel: bump 5.4 to 5.4.74
Removed upstreamed patches:
 mvebu/patches-5.4
   409-phy-marvell-comphy-Convert-internal-SMCC-firmware-re.patch

All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64
Run-tested: ipq806x/R7800, x86_64, lantiq/Easybox 904 xDSL

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64 build/run]
[added lantiq test report]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-02 16:33:25 +01:00
Yousong Zhou
bd0b820068 x86: fix touching bootloader "upgraded" mark
The mount point is "/tmp/boot", the path in the boot partition is
"/boot/grub/upgraded".

Origin of this mark b9c1cf16 ("x86: add preinit hook for bootloader
upgrade")

Fixes 32f675ca ("x86: fix grub-bios-setup fail during sysupgrade")

Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140
Reported-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-11-02 21:09:22 +08:00
Petr Štetiar
ec0ec0428e sdk: fix missing include directories
It's not possible to compile some applications which are using
`-Werror=missing-include-dirs` compiler flags with the SDK as some
target directories are missing in the SDK tarball:

 cc1: error: staging_dir/target/usr/include: No such file or directory [-Werror=missing-include-dirs]
 cc1: error: staging_dir/target/include: No such file or directory [-Werror=missing-include-dirs]

Fix this by adding the missing directories in the SDK.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-02 08:39:49 +01:00
David Bauer
e73d866c6f ipq40xx: enable RX hash / CTAG TX offloading for single-phy
This re-enables offloading features disabled by
commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging").

Single-PHY devices use port-based VLANs on the switch, therefore no
S-TAG magic is involved here. Re-enabling these features restores
throughput back to 950 Mbit/s.

Reported-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-01 15:30:22 +01:00
David Bauer
4c5eb1040f ath79: use correct firmware name for UniFi AP
The Ubiquiti UniFi AP does not have a AHB connected radio but a PCI one.
Also the EEPROM ist only 0x440 bytes of length.

Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-01 15:30:05 +01:00
David Bauer
d011952d19 ath79: remove AT803X config symbol from subtargets
The AT803X_PHY kernel config symbol is already enabled target-wide. SO
it does not have to be enabled for individual subtargets.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-01 15:29:58 +01:00
David Bauer
c741ca5291 ath79: drop upstreamed patch
Patch was upstreamed a long time ago (over 2 years) as commit
a08227a206b8d ("MIPS: ath79: select the PINCTRL subsystem").

When porting this patch to a newer kernel, nobody noticed we now patch a
Broadcom platform. This is clearly not intended. So drop this patch and
pretend nothing ever happened.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-01 15:29:06 +01:00
John Audia
b4c02c9998 kernel: bump 5.4 to 5.4.73
Removed upstreamed patches:
 generic/pending-5.4
   445-mtd-spinand-gigadevice-Only-one-dummy-byte-in-QUA.patch
   446-mtd-spinand-gigadevice-Add-QE-Bit.patch
 pistachio/patches-5.4
   150-pwm-img-Fix-null-pointer-access-in-probe.patch

Manually rebased:
 layerscape/patches-5.4
   801-audio-0011-Revert-ASoC-fsl_sai-add-of_match-data.patch
   801-audio-0039-MLK-16224-6-ASoC-fsl_sai-fix-DSD-suspend-resume.patch
   801-audio-0073-MLK-21957-3-ASoC-fsl_sai-add-bitcount-and-timestamp-.patch
   820-usb-0009-usb-dwc3-Add-workaround-for-host-mode-VBUS-glitch-wh.patch

All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711,
              mvebu (mamba, rango), x86_64, ramips/mt7621
Run-tested: ipq806x/R7800, mvebu (mamba, rango), x86_64, ramips (RT-AC57U)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[alter 820-usb-0009-usb-dwc3-Add-workaround-for-host-mode-VBUS-glitch-wh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-01 14:44:06 +01:00
Adrian Schmutzler
2aa558c49a target: remove obsolete kernel version switches for 4.19
This removes unneeded kernel version switches from the targets after
kernel 4.19 has been dropped.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-30 19:45:24 +01:00
Adrian Schmutzler
2785126650 kernel: remove support for kernel 4.19
We use 5.4 on all targets by default, and 4.19 has never been released
in a stable version. There is no reason to keep it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-30 19:29:59 +01:00
Johannes Kimmel
3824fa26d2 octeon: disable edgerouter image
This patch disables the image for edgerouter devices by default, since
it isn't able to boot at the moment.

Currently the edgerouter image won't boot. Current kernels have an
option CONFIG_CAVIUM_CN63XXP1 that needs to be enabled for this chip.

If the kernel was compiled without this option, following message is
displayed and the machine reboots:

[   36.778028] Kernel panic - not syncing: OCTEON II DCache prefetch workaround not in place (cfa0000c).
[   36.778028] Please build kernel with proper options (CONFIG_CAVIUM_CN63XXP1).
[   36.794398] Rebooting in 1 seconds..

This was last confirmed on 2020-10-29.

The description of this option states, that enabling it will possibly
cause performance issues on other chips.

Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
2020-10-30 19:26:09 +01:00
Daniel Golle
37ef2197e6 kernel: move kmod-i2c-bcm-iproc to I2C menu
A typo resulted in that module having it's own menu.
Move it into the I2C menu as it was most likely intended.

Fixes: 1291274335 ("kernel: package bcm53xx i2c module")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-10-30 15:47:52 +00:00
Paul Spooren
04757f964b build,IB: reload packages/ only if existing
With the fix of external kmod feeds it is possible to ship the
ImageBuilder without any packages except the pseudo packages kernel and
libc. Therefore the local package feeds becomes optional.

This commit adds a check to the package_reload function to only run if
the local feed is existing.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-10-30 00:39:09 +00:00
Paul Spooren
2999f810ff build,IB: include kmods only in local builds
The buildbots generate a kmod archive which should be used instead of a
local copy. This is possible due to the introduction of a kernelversion
specific feed.

This commit adds the ability of using only signed package feeds.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-10-30 00:39:09 +00:00
John Thomson
e91344776b ath79: mikrotik: use vmlinuz (zBoot ELF)
- minimal built initramfs: 10MB vmlinux ELF -> 6MB vmlinuz
- ~5 seconds for kernel decompression, which was equivalent to the
  additional time to load the uncompressed ELF from SPI NOR.
- Removes requirement for lzma-loader, which may have been causing some
  image builds to fail to boot on Mikrotik mt7621.

Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2020-10-29 21:35:03 +08:00
John Thomson
254f51443d mt7621: mikrotik: use vmlinuz (zBoot ELF)
- minimal built initramfs: 11MB vmlinux ELF -> 4.5MB vmlinuz
- ~5 seconds for kernel decompression, which was equivalent to the
  additional time to load the uncompressed ELF from SPI NOR.
- Removes requirement for lzma-loader, which may have been causing some
  image builds to fail to boot on Mikrotik mt7621.

Fixes: FS#3354
Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2020-10-29 21:35:03 +08:00
Chuanhong Guo
c063e27e02 kernel: mips: zboot: put appended dtb into a section
This will make a separated section for dtb appear in ELF, and we can
then use objcopy to patch a dtb into vmlinuz when RAW_APPENDED_DTB
is set in kernel config.

command to patch a dtb:
objcopy --set-section-flags=.appended_dtb=alloc,contents \
        --update-section=.appended_dtb=<target>.dtb vmlinuz vmlinuz-dtb

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-10-29 21:34:56 +08:00
Chuanhong Guo
42af05ca1f ramips: add linux zboot support
linux-mips has zboot code which can create a self-extracting kernel
image.
This allows enabling kernel zboot support for ramips targets.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-10-29 21:20:10 +08:00