Seems stable after 6 days of testing on some of my devices.
Let's switch to 5.4 in order to get more feedback.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
mt7621 overrides KERNEL_DTB to limit dictionary size, which isn't needed
for our lzma loader.
This saves 15KB on mt7621 devices using uimage-lzma-loader.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit increases the hardware SPI frequency from 24.2MHz to 48.3MHz.
[ 5.314163] m25p80 spi0.0: speed: 24166666/40000000, rate: 8, prescal: 2, loops: 226
[ 5.076323] m25p80 spi0.0: speed: 48333333/50000000, rate: 4, prescal: 1, loops: 162
`time cat /dev/mtd2 >/dev/null` is reduced from 5.64s to 4.36s on A104ns,
and from 11.39s to 8.81s on A1004ns.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.
Signed-off-by: René van Dorst <opensource@vdorst.com>
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.
Signed-off-by: René van Dorst <opensource@vdorst.com>
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation
Recovery to stock instruction:
1. Download stock firmware at
http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware
Then repeat the instruction in edae3479e6 to install OpenWrt
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
There are 2 different chips (w25q256fv and w25q256jv) that share
the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes.
Use SFDP header version to differentiate between them.
Fixes broken reboot on 8devices Habanero since f0f35fdac
Signed-off-by: Mantas Pucka <mantas@8devices.com>
This commit adds support for the AVM Fritz!WLAN Repeater 1750E
SOC: Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
WLAN2: QCA9880 5 GHz 802.11 n/ac 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (correct MAC)
- 5 GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
The QCA9550 family of SoCs have a slightly different reset
sequence compared to older chips.
Normally the bootloader performs this sequence, however
some bootloader implementation expect the operating system
to clear the reset. Also get the PCIe resets from OF to
support the second RC of the QCA9558.
This is required for the AVM FRITZ!WLAN Repeater 1750E to work,
as EVA leaves the PCIe bus in reset.
Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala
Signed-off-by: David Bauer <mail@david-bauer.net>
The previous spi-max-frequency value did not work with all the CPU speed
settings (configurable with rbcfg or from the stock firmware); the new
one does for the three of them.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Improve the status LED functionality in GL-AR750
by adding the definitions for different statuses
(boot, failsafe, running, flashing).
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This adds the board name from ar71xx to support upgrade without
-F for the TP-Link TL-WA901ND v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Now that the x86 target uses the new image generation code we can also
attach metadata to the created images.
As currently the `SUPPORTED_DEVICES` list is empty, no JSON metadata is
attached, however the signing happens in the same step.
This results in signature verification for x86 images.
Signed-off-by: Paul Spooren <mail@aparcar.org>
From kernel 4.20 msm-gpio driver is broken and cause the
malfunction of the buttons on every ipq806x target.
Add a patch to fix this.
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This applies further fixes to the DTS of ZyXEL NBG6716 based on
what is found in ar71xx (mach-nbg6716.c):
- use WiFi label names as in ar71xx
- fix WPS gpio number
- fix GPIO_ACTIVE_HIGH and mode for WiFi switch
- add codes for USB eject buttons
- fix node name for "internet" LED
This device has separate LEDs for WAN and "Internet". As the WAN-LED
(and the four LAN-LEDs) are driven independent of the setup in
DT/01_leds, the "internet" LED is left unassigned (in contrast to
ar71xx, where it was set up effectively as a second WAN LED)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some devices have bootloaders with broken lzma code resulting in failed
decompression or corrupted kernel code.
This image recipe allows to sacrifice 5KB for OpenWrt LZMA loader and
take over the task of decompress kernel.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Loader platform is a per-soc variable instead of a per-device one.
Determine corresponding loader platform at the beginning of image
Makefile.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Enables spi-mem interface usage. It speeds up flash read
in about 3x while it also workaround a possible hardware
bug when normal spi read is used.
Fixes: FS#2742
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reimplements read optimization on top of spi-mem. Similar to
what 461-spi-ath79-add-fast-flash-read.patch used to do with
the dropped flash read interface.
It accelerate only fast-read op reading flash directly from
memory mapped region. 'm25p,fast-read' must be set in order
to use the new spi-mem.
It improved read speed up to 3x on old devices (tplink,tl-wr2543-v1)
while no speed improvement was noticed on newer devices like
(tplink,archer-c7-v2).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
forcedeth is necessary to use the integrated
ethernet controller of Nvidia nForce chipset.
There are PC motherboards with this chipset
from 2001 that run 32bit Athlon XP CPUs and
more modern ones up to 2009 that can run Intel
and AMD 64bit processors, so add this to
all non-geode x86 targets.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
These patches were necessarry for Atheros and some Intel WiFi cards.
After short testing, the current upstream driver state is enough for
these WiFi cards to work. If there are still some issues with other
devices, the patches could be easily restored.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370
Hardware:
SoC: Marvell Armada 88F6707-A1
CPU: Cortex-A9 1200 MHz, 1 core
Flash: SPI-NOR 1 MiB, NAND 512 MiB
RAM: DDR3 512 MiB
Ethernet: 1x 10/100/1000 Mbps
USB: 1x 2.0, 1x 3.0
SATA: 2x 3.0 Gbps
LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
RTC: Ricoh RS5C372A, I2C, no battery
Flash instruction (UART+TFTP):
1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
2. Remove any hard drive from inside the bays.
3. Boot the Openwrt initramfs image using the U-Boot serial console:
tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
bootm 0x1200000
4. Flash the sysupgrade image using the Openwrt console:
sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
5. Wait until it finish, the device will reboot with Openwrt installed
on the NAND flash.
Note:
- Device shuting down doesn't work, even if the power slide switch is
used. We must first, via MDIO, set the unused LED2 at the ethernet
phy0 to off state. Reboot works ok.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The USB LED assignment to internal ports was swapped.
Fix it.
We also explicitly checked that the LED label numbers match those
on the device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2.4 GHz Wifi on ath79 is set up in 10-ath9k-eeprom, but in ar71xx
it was done with ath79_register_wmac.
Thus, the following errors are observed on the device:
ath: phy1: Unable to initialize hardware; initialization status: -5
ath9k 18100000.wmac: failed to initialize device
ath9k: probe of 18100000.wmac failed with error -5
This patch changes the ath79 support to properly use wmac as well.
This will also require fixing the MAC address in a different way.
Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
[several adjustments to 10-fix-wifi-mac, use correct MAC address,
rewrite commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device with 4 MiB flash and 32 MiB RAM won't be able to run OpenWrt in
a sufficient manner without tweaks, so don't build images for them by
default.
This includes all BCM6338, BCM6345 and BCM6348 "generic" devices,
as there are no supported devices of these with more than that.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
previously we rely on the failsafe setup in preinit scripts to disable
built-in switch implicitly for single-port devices. This doesn't work
anymore due to preinit script removal.
this patch explicitly disable built-in switch for needed devices.
Fixes: a8d62a4eb1 ("ramips: remove set_preinit_iface script")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
