Otherwise, the last defined value will be set for all devices.
Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Youku YK-L1 has a huge storage space up to 32 MB. It is better to
use a higher spi clock to read or write serial nor flash chips.
Youku YK-L1 has Winbond w25q256fvfg on board that can support
104 MHz spi clock so 48 MHz is safe enough.
The real frequency can only be sysclk(580MHz ) /3 /(2^n) so 80 MHz
defined in dts file will set only 48 MHz in spi bus.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add the same patch to 5.10 too. The patch is in process of being
upstreamed.
Fixes: 8cc0fa8fac ("ath79: cfi: cmdset_0002: amd chip
0x2201 - write words")
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device is a wireless router working on 2.4GHz band based on
Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103
wireless chip and Realtek RTL8366RB/S switches. Due to two different
switches being used also two different devices are provided.
Specification:
- 400 MHz CPU
- 64 MB of RAM
- 32 MB of FLASH (NOR)
- 3x3:2 2.4 GHz 802.11bgn
- 5x 10/100/1000 Mbps Ethernet
- 4x LED, 3x button, On/Off slider, Auto/On/Off slider
- 1x USB 2.0
- bare UART header place on PCB
Flash instruction:
- NOTE: Pay attention to the switch variant and choose the image to
flash accordingly. (dmesg / kernel logs can tell it)
- Methods for flashing
- Apply factory image in OEM firmware web-gui.
- Sysupgrade on top of existing OpenWRT image
- U-Boot TFPT recovery for both stock or OpenWRT images:
The device U-boot contains a TFTP server that by default has
an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot
there is a time window, during which the device allows an image to
be uploaded from a client with address 192.168.11.2. The image will
be written on flash automatically.
1) Have a computer with static IP address 192.168.11.2 and the
router device switched off.
2) Connect the LAN port next to the WAN port in the device and the
computer using a network switch.
3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A
arp -s 192.168.11.1 02:AA:BB:CC:DD:1A
4) Initiate an upload using TFTP image variant
curl -T <imagename> tftp://192.168.11.1
5) Switch on the device. The image will be uploaded subsequently.
You can keep an eye on the diag light on the device, it should
keep on blinking for a while indicating the writing of the image.
General notes:
- In the stock firmware the MAC address is the same among all
interfaces so it is left here that way too.
Recovery:
- TFTP method
- U-boot serial console
Differences to ar71xx platform
- This device is split in two different targets now due to hardware
being a bit different under the hood. Dynamic solution within the same
image is left for later time.
- GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device
cover, were the wrong way around and were renamed qos_on -> movie_off,
qos_off -> movie_on. Associated key codes remained the same they were.
The device tree source code is mostly based on musashino's work
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Generally, in upstream CFI flash memory driver uses buffers for write
operations. That does not work with AMD chip with id 0x2201 and we must
resort to writing word sized chunks only. That is, to not apply general
buffer write functionality for this given chip.
Without the patch kernel logs will be flooded with entries like below:
MTD do_erase_oneblock(): ERASE 0x01fa0000
MTD do_write_buffer(): WRITE 0x01fa0000(0x00001985)
MTD do_erase_oneblock(): ERASE 0x01f80000
MTD do_write_buffer(): WRITE 0x01f80000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f8000a.
jffs2: Write clean marker to block at 0x01a60000 failed: -5
MTD do_erase_oneblock(): ERASE 0x01f60000
MTD do_write_buffer(): WRITE 0x01f60000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f6000a.
jffs2: Write clean marker to block at 0x01a40000 failed: -5
References: http://patchwork.ozlabs.org/project/linux-mtd/patch/20210309174859.362060-1-sandberg@mailfence.com/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to usptream fix submission]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Physical port order watched from the back of the device is:
4 / 3 / 2 / 1 / WAN which also matches corresponding leds.
This patch corrects LuCI switch webpage LAN port order.
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[improve commit title, fix sorting in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Improve compatibility of the device tree include file. Now a new .dtsi
file will support both PSG1218A, PSG1218B and K2G.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title, rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
From many teardown image in the internet, I find Phicomm K1/k2 series use
Winbond W25Q64/W25Q128 or GigaDevice GD25Q64/GD25Q128 Flash chips. both of
them support 100+ MHz clock spi operate and fast-read instruction. PSG1218
with W25x or GD25x has been tested and it can run well in OpenWrt v19.07.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
HIWIFI HC5x61 devices support high speed spi clock up to 100+ MHz.
So set spi frequency to 80 MHz here (Due to frequency division the
real clock is 48 MHz).
I have tested HC5661 and it can run well in OpenWrt v19.07.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[adjust commit title and wrap message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There is an ASMedia ASM1480 PCIe switch found on mt7622-rfb1 and the
BPi-R64, allowing the user to switch between SATA and PCIe1 which share
the same pins on the SoC.
This chip is not present on the Linksys E8450, it doesn't have SATA.
Remove definitions for GPIO90 from DTSI to prevent it from being
copy&pasted or otherwise causing confusion.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With kernel 5.10, exfat is out of staging and in tree.
Added small hack to make it work with kernel 5.4 as well.
Added removed config options for 5.4 to generic config.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0x900000, size 0x600000
6291456 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "priKernSize";
priKernSize=0x0600000
Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.
Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0xa00000, size 0x400000
4194304 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "pri_kern_size";
pri_kern_size=0x400000
Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.
Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
Update 5.10 generic config to add missing options prompting during builds,
when setting CONFIG_ALL_KMODS. Refresh the x86 subtargets to drop symbols
added to the generic config.
Also fix a typo in 5.4/5.10 generic configs: "CONFIG_CONFIG_KVM_AMD_SEV".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
ZyXEL NBG6817 comes with an eMMC which contains a GPT partition named
'rootfs_data'. This currently confuses fstools and makes it pick that
(not suitable) partition.
Use the newly introduced fstools_ignore_partname=1 kernel cmdline
parameter to have fstools ignore that partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A SPI NOR flash should not be target-specific, so move it to generic in
case another platform needs to use it.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Without that, after merging support to master, the device fails to boot
due to LZMA decompression error:
3: System Boot system code via Flash.
## Booting image at bc080000 ...
raspi_read: from:80000 len:40
. Image Name: MIPS OpenWrt Linux-5.4.99
Created: 2021-02-25 23:35:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1786664 Bytes = 1.7 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:80040 len:1b4328
............................ Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
Use lzma-loader to fix it.
Fixes: 59d065c9f8 ("ramips: add support for ZTE MF283+")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
HC5661 does not have USB port, remove usb power control pin.
HC5x61 do not have LAN LEDs, remove ethernet LED control pin.
Only HC5861 has PA in 2.4G channel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.
Set maximum kernel size and disable image building for this board.
Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
Signed-off-by: David Bauer <mail@david-bauer.net>
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Bananapi BPi-R64 got a SATA interface which cannot be used at the
same time as the second mPCIe slot. The decission is made by hogging
GPIO 90.
Embed two addtional DT overlay blobs into the image to allow bootloader
selection of either SATA or PCIE1 feature.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add new target feature 'dt-overlay' which makes DTC keep the symbol
names in the generated dtb.
Make sure additional DT overlay sources specified by the new device
variable DEVICE_DTS_OVERLAY get compiled together with the main DTS
(currently overlays got to be in the same folder). Let Build/fit pass
the generated DT overlay blobs to mkits.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DTR GPIO isn't actually needed and triggers boot warning.
TX pin was off by one (GPIO 19 instead of GPIO 18).
Reported-by: @tophirsch
Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop autogenerated kernel config options. These aren't needed to build and
can obscure options relevant to the subtarget.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update generic config to add missing options that prompt during builds. Run
"make kernel_oldconfig" to refresh malta target config.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The rtl83xx-phy driver is necessary for proper configuration of the
PHYs if U-Boot hasn't done that.
1000Base-T SFPs often contains a Marvell 88E1111 and will not work
without this driver. Include it by default to support copper SFPs.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
There is no need to define a static link or a phy for the sfp
ports. Using phy-mode and managed properties to describe the
link to the sfp phy.
We have to keep the now unconnected virtual "phys" because the
switch driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.
Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
From the validate docs in include/linux/phylink.h:
When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the
MAC driver to return all supported link modes.
Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
