Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add multiple patch for krait-cc modernization and multiple fixup for the
driver. Also modify a patch to enable the qsb fixed clock and add pxo to
krait-cc node.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
nand_pins definition is now shipped in ipq8064 dtsi. Rework the
nand_pins definition for wg2600hp3 5.15 files.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch has changed implementation and now the binding has changed.
Replace the old binding with boot-partitions and reimplement the
definition with the new definition.
The new definition is:
<offset1 size1 offset2 size2 offset3 ...>
and now supports sparsed patch.
Also add missing binding in some dts and add the backup boot partition
to the boot-partitions list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove useless spm patch as using the normal qcom,spm compatible is
enough to register it with no clks.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use a new implementation by using a devfreq driver to scale the shared
cache of the krait cpu cores.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport devfreq new cpufreq based PASSIVE governor needed for devfreq
based fab and cache scaling.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reorganize dtsi patches with upstream version and drop dtsi in 5.15
files.
Also add an additional upstream patch for hwspinlock support.
Refresh all the dts with needed changes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This doesn't cause any panic anymore and no regression are observed with
ath10k. Remove this additional patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove qcom adm Documentation patch that is not needed for the target.
Probably a leftover when the adm bus was added, now merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In preparation for a cleanup of 5.15 patches copy the files dir to 5.10
and 5.15 kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Removed following upstreamed patch:
* bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add missing scaling_available_frequencies sysfs entry for dedicated
cpufreq driver.
This sysfs entry is not standard and each cpufreq driver needs to
provide it and declare it in the cpufreq driver struct attr.
Fixes: 5dbbefcbcc ("ipq806x: introduce dedicated krait cpufreq")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Fixes: #10275
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.
Same as commit 2047058 ("ipq806x: utilize nvmem-cells
for pre-calibration data")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
There is a mr25h256 spi flash on this machine. From the mtd backup
of the stock firmware, this spi flash is empty.
[ 3.652745] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16,
fifo:64
[ 3.653925] spi-nor spi0.0: mr25h256 (32 Kbytes)
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix wrong CPU OPP for ipq8062. Revision of the SoC added an
extra 25mV for every pvs. Also fix the voltage min/max value
that were wrong.
Reviewed-by: Robert Marko robimarko@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The existing device tree has incorrect definitions for usb3_0 and usb3_1
and the blocks they depend upon: their addresses and interrupts are
swapped. However, their clocks and resets are not. The result is that
the USB blocks are non-functional if only one of them is enabled.
This fix backports the definitions from mainline Linux 5.15 to
OpenWrt's 5.10 dtsi additions. See the relevant mainline code here:
https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148
This fix does not break existing ports. But some ports may have enabled
both USB blocks even thought their board only implements one, because
enabling a single USB block would not have worked before this fix.
This means that revisiting all ports of ipq806x devices that implement
a single USB port is advised. This work must be done by maintainers that
can determine which USB block corresponds to the implemented port on
their hardware.
Note that this fix swaps the names of the hardware ports. This is
unfortunate, but will happen anyway when switching to kernel 5.15. Thus,
it is best to do this ASAP, before users get to depend on port names.
It is strongly recommended that this fix is backported to 22.03 before
its release. This will minimize the number of users affected by the port
name swap.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.
The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.
The other symbols are disabled and should be in the generic config.
This commit also removes these symbols from subtargets.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Fix dedicated cpufreq for kernel 5.15 as they changed module
order and now it can happen that cpufreq probe after cache driver.
Also add lock between cache scaling in set_target as it's now required
by opp functions.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
