Commit Graph

39735 Commits

Author SHA1 Message Date
Zoltan HERPAI
f9ecb0d562 sunxi: add Orange Pi 2 support
- H3 @ 1.3 GHz
- 1GiB DDR3
- 10/100Mbps Ethernet
- Realtek RTL8189ETV wifi
- 4 USB 2.0

Difference to the "Orange Pi Plus" is the lack of Gbit ethernet
and lack of onboard flash.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2017-11-06 16:39:41 +01:00
Rosen Penev
e555153807 ag71xx: Switch from driver to kernel macro for NAPI_WEIGHT.
NAPI_POLL_WEIGHT was introduced in the kernel for exactly this purpose 5 years ago.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-11-06 16:39:41 +01:00
Sergey Ryazanov
890e668273 ixp4xx: drop the jumbo frame support
Current jumbo frame support code allocates rxbuffers of the maximum size
supported by the hardware (~14KB). This happens at the device open time
even if the configured MTU is lower (e.g. if it configured to standard
1500 bytes). Such behavior effectivly prevents interface start on boards
with a low ammount of RAM (e.g. WRT300N v2), since the kernel simly can
not allocates of ~0.8MB (14KB x 64).

So remove jumbo frame support for now.

Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-11-06 16:39:41 +01:00
Sergey Ryazanov
204f3f5987 ixp4xx: fix non-standard phy support
The patch, which adds multiphy support, adds new path for non-standard
PHYs (e.g. MV88E6060 switch IC) to avoid using kernel phy framework. All
work well except the link status traking (Duplex and Speed), which is
reseted as soon as PHY connection procedure is done. This leads to lost
of the link status of non-standard PHY, which is configured exactly in
the ixp4xx_phy_connect() function.

Move the generic reset of a link state to the ixp4xx_phy_connect()
function to the code path, which is intended for handling of a normal
PHY.

Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-11-06 16:39:41 +01:00
Marek Vasut
6d2f3b1b19 package: kernel: dtc: Add DTO support
Add patch with the DT overlay support into the DTC package.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-11-06 16:39:41 +01:00
Ralph Sennhauser
f5468d2486 openssl: fix cryptodev config dependency
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
2017-11-06 16:39:41 +01:00
Kayo Phoenix
6a3565985f sunxi: Added profile for HAOYU Electronics Marsboard A10
The MarsBoard was a short-lived credit-card sized, extendable board with an Allwinner A10 SoC.
http://linux-sunxi.org/MarsBoard_A10

Signed-off-by: Kayo Phoenix <kayo@illumium.org>
[Forward-ported to new target layout:]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2017-11-06 16:39:41 +01:00
Arjun AK
63d7c45886 iwinfo: add "PKG_MIRROR_HASH" to the Makefile
Defining it will let the build tool download the tarball file from
a buildbot server, avoiding a clone of the source repo.

Signed-off-by: Arjun AK <lede@arjunak.com>
2017-11-06 16:39:41 +01:00
Felix Fietkau
c078386ae3 ar71xx: only use SPI NOR 4K sectors on smaller flash chips for mikrotik devices
On NOR based Mikrotik devices, 4K sectors significantly slow down
firmware flashing and jffs2 usage. On NAND based devices they may be
necessary to run rbcfg (the boot loader config is often on SPI NOR).

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-06 16:38:28 +01:00
Felix Fietkau
c08293893a kernel: add support for limiting 4K erase sector support based on flash chip size
Some targets need 4K sectors for small flash chips (e.g. some
routerboards, where the entire chip is just one "erase block"), whereas
on other devices 4K sectors lead to horrible flash erase/write
performance.

Set the default limit in the generic kernel configuration to 4 MiB to
ensure that all new platforms don't use 4K sectors for bigger flash
chips. On all existing targets use 16 MiB for now to avoid regressions.
They will be changed individually in follow-up commits.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-06 16:38:25 +01:00
Felix Fietkau
94491a1571 ubox: update to the latest version, fixes syslog issues
7a49632 logd: use uloop instead of ustream_fd for syslog
69d6542 logd: only create pipe in stream mode
df30c8c logread: terminate after EOF
bdcacad logd: implement oneshot mode for stream log read
4a10d4e logread: use oneshot mode without -f, wait for logd to close
ea3d7fa logd: enforce line length limit for ubus based log messages as well
960a29d logread: remove leftover debug code
a081904 logread: fix line buffer size
2c0d9cf logd: move stripping of newlines to log_add()

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-06 11:58:40 +01:00
Philip Prindeville
e03dcf494e iperf3: update to 3.3 and refresh patches
Taking the same patchset I've submitted upstream for inclusion.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
2017-10-31 14:19:51 -06:00
John Crispin
bd60c9063d bubox: update to latest git HEAD
729f47f jshn: read and write 64-bit integers

Signed-off-by: John Crispin <john@phrozen.org>
2017-11-06 10:06:35 +01:00
Stefan Lippers-Hollmann
9a221c6d69 ip806x: nbg6817: sysupgrade support both targets for kernel/ rootfs partitions
With this commit and the previous "nbg6817: don't hardcode the rootfs location
by using append-rootblock instead" applied, it is possible to boot- and
sysupgrade from both dual-boot sets (the primary mmcblk0p4+mmcblk0p5 or the
alternative mmcblk0p7+mmcblk0p8). However the sysupgrade support does not
toggle between both dual-boot sets between firmware upgrades so far.

The partition map of the eMMC used in the nbg6817 is:

Found valid GPT with protective MBR; using GPT.
Disk /dev/mmcblk0: 7471104 sectors, 3.6 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): XXX
Partition table holds up to 12 entries
First usable sector is 34, last usable sector is 7471070
Partitions will be aligned on 2-sector boundaries
Total free space is 1 sectors (512 bytes)

Number  Start (sector)    End (sector)  Size       Code  Name
   1              34            8225   4.0 MiB     FFFF  rootfs_data
   2            8226           16417   4.0 MiB     FFFF  romd
   3           16418           18465   1024.0 KiB  FFFF  header
   4           18466           26657   4.0 MiB     FFFF  kernel
   5           26658          157729   64.0 MiB    FFFF  rootfs
   6          157730          159777   1024.0 KiB  FFFF  header_1
   7          159778          167969   4.0 MiB     FFFF  kernel_1
   8          167970          299041   64.0 MiB    FFFF  rootfs_1
   9          299042          823329   256.0 MiB   FFFF  bu1
  10          823330         7471069   3.2 GiB     FFFF  bu2

rootfs_data is the ext4 formatted overlay of the OEM firmware, LEDE
ignores it due to its (too) small size.

romd/ bu1 are initialized with zeroes (0x00) and unused.

bu2 is formatted with ext4 and used for streamboost and other optional
functionality by the OEM firmware, it is reformatted during factory
resets of the OEM firmware.

header/ header_1 contains version information for the corresponding
vendor firmwares installed to kernel/rootfs or kernel_1/ rootfs_1, the
format hasn't been completely reverse engineered so far and remains
left untouched by LEDE:

V1.00(ABCS.2)C0:
 00000000  00 00 a7 74 01 32 f0 00  56 31 2e 30 30 28 41 42  |...t.2..V1.00(AB|
 00000010  43 53 2e 32 29 43 30 00  ff ff ff ff ff ff ff ff  |CS.2)C0.........|
 00000020  ff ff ff ff ff ff ff ff  00 00 d5 dc 4e 42 47 36  |............NBG6|
 00000030  38 31 37 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |817.............|
 00000040  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000060  ff ff ff ff ff ff ff ff  ff ff ff ff 00 00 22 a3  |..............".|
 00000070  00 1c 70 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |..p.............|
 00000080  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000800  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
 *
 00100000

V1.00(ABCS.5)C0:
 00000000  00 00 bf 94 01 46 d8 00  56 31 2e 30 30 28 41 42  |.....F..V1.00(AB|
 00000010  43 53 2e 35 29 43 30 00  ff ff ff ff ff ff ff ff  |CS.5)C0.........|
 00000020  ff ff ff ff ff ff ff ff  00 00 d6 5a 4e 42 47 36  |...........ZNBG6|
 00000030  38 31 37 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |817.............|
 00000040  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000060  ff ff ff ff ff ff ff ff  ff ff ff ff 00 00 c0 2c  |...............,|
 00000070  00 1c 58 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |..X.............|
 00000080  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00010000  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
 *
 00100000

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-10-29 03:11:51 +01:00
Stefan Lippers-Hollmann
b583aaf5aa ip806x: nbg6817: don't hardcode the rootfs location by using append-rootblock instead
This changes the cmdline from:

Kernel command line: root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)

to

Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)

As a consequence booting from the alternative dual-boot partition set
(root=/dev/mmcblk0p8) becomes possible.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-10-29 02:55:27 +01:00
Koen Vandeputte
06d5d01e8a uqmi: replace legacy command invoke with newer type
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-10-24 16:20:22 +02:00
Koen Vandeputte
09582d6b4d uqmi: also try newer pin verification
Newer devices tend to only support the newer version of the pin
verification command, so also try that one.

Fixes PIN issues with modems like the Sierra Wireless MC7455

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-10-24 16:20:21 +02:00
John Crispin
5b3e35d85b ubox: update to latest git HEAD
da5b8b4 log/syslog: Add missing static to two structs.
dd61c9f ubox: Replace { 0 } with {}.

Signed-off-by: John Crispin <john@phrozen.org>
2017-11-06 09:07:39 +01:00
John Crispin
f62e2f611c procd: update to latest git HEAD
53e92d4 procd: lower the logging threshold
b39c362 service: Start services normally when seccomp is disabled
3ba6b45 procd: add missing new lines inside debug code
56a02e3 service: fix service_handle_event array
d4a183f service: fix SERVICE_ATTR_NAME usage in service_handle_set

Signed-off-by: John Crispin <john@phrozen.org>
2017-11-06 08:50:18 +01:00
Michal Sojka
0e300a3a71 procd: Always tell cmake whether to include seccomp support or not
Without this change, when a user disables seccomp support in .config,
procd does not get recompiled unless the package is cleaned manually.
It is because when -D option is missing from cmake command line, cmake
uses cached value from the previous run where seccomp was enabled.

Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
2017-11-03 22:31:42 +01:00
John Crispin
727ab294d0 ubus: update to latest git HEAD
24ffe9b libubus-req: add data_cb callback handling for ubus notifications

Signed-off-by: John Crispin <john@phrozen.org>
2017-11-06 08:31:38 +01:00
Roman Yeryomin
156f2df879 ipq806x: ipq4019: add ap-dk01.1-c1 board support
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)

First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize

Further upgrades via sysupgrade.

Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition

Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.

Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.

Changes since v2:
- based on dts(i) rework/cleanup submitted:
  http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:24:26 +02:00
Roman Yeryomin
a22e2bd37d ipq806x: ipq4019: dts: fix maximum cpu speed
Supported frequencies of all ipq40xx chips are 48, 200, 500 and 716.8 MHz.
Previous 666MHz setting was most likely related to instability of early
chips/boards made before mass production.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:19:32 +02:00
Roman Yeryomin
21802ce3ab ipq806x: ipq4019: dts: remove spi chip node from ap-dk01 dtsi
All ap-dk01 boards have different spi chips, thus no point in keeping it in dtsi.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:19:19 +02:00
Roman Yeryomin
97a836318f ipq806x: ipq4019: dts: move ap-dk01 networking entries to dtsi
That is mdio/ethernet and wifi are present on all ap-dk01 boards.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:19:02 +02:00
Roman Yeryomin
45b1042a0a ipq806x: ipq4019: dts: remove counter entry from ap-dk01 boards
There is no code implementing "qcom,qca-gcnt", so no point in keeping it.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:18:51 +02:00
Roman Yeryomin
91f0345801 ipq806x: ipq4019: dts: move ap-dk01 tcsr nodes to dtsi
tcsr configuration is the same for all ap-dk01 boards

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:18:38 +02:00
Roman Yeryomin
ba9aa76a3a ipq806x: ipq4019: dts: remove crypto nodes from board dts
crypto and cryptobam are already present in dtsi used by these boards:
- fritz4040
- nbg6617
- rt-ac58u

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:18:24 +02:00
Roman Yeryomin
1abc788924 ipq806x: ipq4019: dts: move xo and timer nodes to SoC dtsi
xo and timer are common thing and it makes more sense to keep them in SoC dtsi

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:18:11 +02:00
Roman Yeryomin
ab3ab6241f ipq806x: ipq4019: dts: fix pinctrl node name
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:17:58 +02:00
Yousong Zhou
f0c37f6ceb libunwind: disable building with ssp
If we enable -fstack-protector while building libunwind, function
__stack_chk_fail_local will be referred to for i386 and powerpc32
arches.  This will cause link failure because the default gcc build
specs says no link_ssp if -nostdlib is given.

The error message:

    OpenWrt-libtool: link: ccache_cc -shared  -fPIC -DPIC  .libs/os-linux.o mi/.libs/init.o mi/.libs/flush_cache.o mi/.libs/mempool.o mi/.libs/strerror.o x86/.libs/is_fpreg.o x86/.libs/regname.o x86/.libs/Los-linux.o mi/.libs/backtrace.o mi/.libs/dyn-cancel.o mi/.libs/dyn-info-list.o mi/.libs/dyn-register.o mi/.libs/Ldyn-extract.o mi/.libs/Lfind_dynamic_proc_info.o mi/.libs/Lget_accessors.o mi/.libs/Lget_proc_info_by_ip.o mi/.libs/Lget_proc_name.o mi/.libs/Lput_dynamic_unwind_info.o mi/.libs/Ldestroy_addr_space.o mi/.libs/Lget_reg.o mi/.libs/Lset_reg.o mi/.libs/Lget_fpreg.o mi/.libs/Lset_fpreg.o mi/.libs/Lset_caching_policy.o x86/.libs/Lcreate_addr_space.o x86/.libs/Lget_save_loc.o x86/.libs/Lglobal.o x86/.libs/Linit.o x86/.libs/Linit_local.o x86/.libs/Linit_remote.o x86/.libs/Lget_proc_info.o x86/.libs/Lregs.o x86/.libs/Lresume.o x86/.libs/Lstep.o x86/.libs/getcontext-linux.o  -Wl,--whole-archive ./.libs/libunwind-dwarf-local.a ./.libs/libunwind-elf32.a -Wl,--no-whole-archive  -L/var/lib/bbmnt/buildbot/slaves/dave-builder/i386_i486/build/sdk/staging_dir/target-i386_i486_musl-1.1.16/usr/lib -L/var/lib/bbmnt/buildbot/slaves/dave-builder/i386_i486/build/sdk/staging_dir/target-i386_i486_musl-1.1.16/lib -L/var/lib/bbmnt/buildbot/slaves/dave-builder/i386_i486/build/sdk/staging_dir/toolchain-i386_i486_gcc-5.4.0_musl-1.1.16/usr/lib -L/var/lib/bbmnt/buildbot/slaves/dave-builder/i386_i486/build/sdk/staging_dir/toolchain-i386_i486_gcc-5.4.0_musl-1.1.16/lib -lc -lgcc  -Os -march=i486 -fstack-protector -Wl,-z -Wl,now -Wl,-z -Wl,relro -nostartfiles -nostdlib   -Wl,-soname -Wl,libunwind.so.8 -o .libs/libunwind.so.8.0.1
    .libs/os-linux.o: In function `_Ux86_get_elf_image':
    os-linux.c:(.text+0x588): undefined reference to `__stack_chk_fail_local'
    x86/.libs/Lregs.o: In function `_ULx86_access_fpreg':
    Lregs.c:(.text+0x25b): undefined reference to `__stack_chk_fail_local'
    x86/.libs/Lresume.o: In function `_ULx86_resume':
    Lresume.c:(.text+0xdc): undefined reference to `__stack_chk_fail_local'
    collect2: error: ld returned 1 exit status
    Makefile:2249: recipe for target 'libunwind.la' failed

The snippet from gcc -dumpspecs

    %{!nostdlib:%{!nodefaultlibs:%(link_ssp) %(link_gcc_c_sequence)}}

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-11-06 10:49:58 +08:00
Alexander Couzens
2e1f73a79f
mt7620: image.mk: make elecom-header reproducible
elecom-header adds a timestamp dependency. Replace
the timestamps with SOURCE_DATE_EPOCH [0] variable.

[0] https://reproducible-builds.org/specs/source-date-epoch/

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-11-06 00:09:18 +01:00
Felix Fietkau
1c68fd6d75 ar71xx: fix section mismatch in TP-Link Archer C7 v4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-05 18:52:14 +01:00
Felix Fietkau
e0d58157d8 ar71xx: fix flash fast read on devices using multiple flash chips
Add a callback to allow the SPI driver to indicate which devices fast
flash read works on.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-05 18:52:12 +01:00
Kevin Darbyshire-Bryant
e0bd225269 wireguard: version bump to 0.0.20171101
Update wireguard to latest snapshot:

9fc5daf version: bump snapshot
748ca6b compat: unbreak unloading on kernels 4.6 through 4.9
7be9894 timers: switch to kees' new timer_list functions
6be9a66 wg-quick: save all hooks on save
752e7af version: bump snapshot
2cd9642 wg-quick: fsync the temporary file before renaming
b139499 wg-quick: allow for saving existing interface
582c201 contrib: add reresolve-dns
8e04be1 tools: correct type for CTRL_ATTR_FAMILY_ID
c138276 wg-quick: allow for the hatchet, but not by default
d03f2a0 global: use fewer BUG_ONs
6d681ce timers: guard entire setting in block
4bf32ca curve25519: only enable int128 if compiler support is sound
86e06a3 device: expand scope of destruct lock
e3661ab global: get rid of useless forward declarations
bedc77a device: only take reference if netns is different
7c07e22 wg-quick: remember to rewind DNS settings on failure
2352ec0 wg-quick: allow specifiying multiple hooks
573cb19 qemu: test using four cores
e09ec4d global: style nits
4d3deae qemu: work around ccache bugs
7491cd4 global: infuriating kernel iterator style
78e079c peer: store total number of peers instead of iterating
d4e2752 peer: get rid of peer_for_each magic
6cf12d1 compat: be sure to include header before testing
3ea08d8 qemu: allow for cross compilation
d467551 crypto/avx: make sure we can actually use ymm registers
c786c46 blake2: include headers for macros
328e386 global: accept decent check_patch.pl suggestions
a473592 compat: fix up stat calculation for udp tunnel
9d930f5 stats: more robust accounting
311ca62 selftest: initialize mutex in routingtable selftest
8a9a6d3 netns: use time-based test instead of quantity-based
e480068 netns: use read built-in instead of ncat hack for dmesg

Compile-tested-for: ar71xx
Run-tested-on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2017-11-04 18:10:21 +01:00
Mathias Kresin
8d3857a347 ath9k: unset the default LED pin if used by platform buttons
Unset the default LED gpio pin if the same gpio pin is used by a button
defined via platform button. It prevents the change of the GPIO value
on wireless up/down or wireless traffic.

Fixes: FS#1129

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-04 09:50:13 +01:00
Florian Beier
c4c72a9a42 ar71xx: fix LED config for DIR-869 A1
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.

Behavior of the LED front after this patch is applied:

cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0   -> white LEDs are OFF
255 -> white LEDs are ON

cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0   -> orange LEDs are OFF
255 -> orange LEDs are ON

If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.

Signed-off-by: Florian Beier <beier.florian@gmail.com>
2017-11-03 20:04:52 +01:00
Edmunt Pienkowsky
fdc7cc9907 base-files: add interval option to netdev LED trigger configuration
Add an uci option to set the interval parameter of the netdev trigger.

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
2017-11-03 20:04:52 +01:00
Mathias Kresin
f9311e4070 ar71xx: wzr-hp-ag300h: drop unused wmac led_pin settings
The GPIOs are used for defined LEDs and therefore are ignored/unset in
the ath9k driver since 192f0a3db8. The wireless led led trigger is
added in userspace since e20965811d, which makes the
ap9x_pci_setup_wmac_led_pin() superfluous.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-03 20:04:52 +01:00
Paul Wassi
67da6a7c5e uboot-kirkwood: update to 2017.09
Upgrade uboot-kirkwood to upstream release 2017.09
Catch up with upstream and move configuration options from
simple defines to Kconfig, as otherwise dependencies would
not be resolved and code would not compile.

Tested-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-03 20:04:52 +01:00
Thibaut VARENE
dfa2930988 ar71xx: mach-rbspi: fix 74x164 support
The platform data was missing the num_registers element which is now
mandatory in linux 4.9

Without this patch, the gpio probing would fail with:
gpio gpiochip1: (74x164): tried to insert a GPIO chip with zero lines

Fixes: #1106

Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-11-03 20:04:51 +01:00
Stefan Lippers-Hollmann
189433e543 ipq806x: nbg6817: sync MAC addresses to the upstream values
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.

interface	  new/ OEM MAC	old MAC

wlan-2.4g (phy1): ethaddr	undefined
wlan-5g   (phy0): ethaddr + 1	undefined
lan             : ethaddr + 2	ethaddr
wan             : ethaddr + 3	ethaddr + 1

This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-11-03 20:04:51 +01:00
Stefan Lippers-Hollmann
6e6d4f2e87 ipq806x: nbg6817: add kmod-fs-ext4 to device packages
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.

/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)

Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile  emergency overlay in place.

Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-11-03 20:04:51 +01:00
Mathias Kresin
56189f1e32 ltq-atm: add missing dependency to kmod-ltq-adsl-*-mei
Commit 2e496876c6 fixed the generation of the depends line for external
kernel modules which makes it possible for the build system to
automatically detect this missing dependency.

This fixes the packaging of kmod-ltq-atm for the ar9, xway and
xway-legacy subtarget.

Fixes: FS#1124

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-03 20:04:40 +01:00
Felix Fietkau
c6f71ad30b build: fix another regression in append-dtb fix
Filter out duplicate generated code for the same dts files

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-03 16:21:24 +01:00
Felix Fietkau
fae5f02912 build: fix regression in append-dtb fix
Strip whitespace from DTS directory
Put the dependency earlier in the chain to avoid make errors

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-03 11:00:20 +01:00
Felix Fietkau
eb58eba08b uclient: update to the latest version, fixes fetch of multiple files
4b87d83 uclient-fetch: fix overloading of output_file variable

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-02 22:54:09 +01:00
Tero Jänkä
82a4b8dd6a netifd: fix dns and domain variables pollution in dhcp.script
Unmodified dns and domain variables could be needed in user script (/etc/udhcpc.user).

Signed-off-by: Tero Jänkä <tero.janka@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (cleanup)
2017-11-02 18:20:55 +01:00
Felix Fietkau
986d9deb3b build: allow calling append-dtb from image build commands
mpc85xx uses this for firmware image files, since the dtb data is not
directly part of the kernel image. This causes build failures in the
image builder.

Fix this by adding a separate build step that runs this call earlier,
reusing the generated file for any calls from kernel or image build
commands.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-02 16:01:18 +01:00
Felix Fietkau
7e2c271a80 gcc: remove support for libgcj/java
It has been removed in gcc 7

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-02 15:58:45 +01:00