New kernel version 6.1 introduced new INITRAMFS option. Add them to the
Initramfs functions to correctly compile initramfs images.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
random_ether_addr is just a reference to eth_random_addr, that was later
dropped in more recent kernel version.
Drop random_ether_addr and use eth_random_addr directly to fix
compilation error in 6.1
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of reference vlan and do strange subtraction, use the handy
struct_group() to create a virtual struct of the same size of the
members. This permits to have a more secure memset and fix compilation
warning in 6.1 where additional checks are done.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With kernel 6.1 ieee2111_ptr is not compiled by default. Add pending
patch to restore this to make backports project compatible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh mglru patch for new kernel version due to very fun backport
changing name from folio to pages.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh pending patches for kernel 6.1.
Changes:
- Refresh mtd patches with new implementation.
- Change 191-rtc-rs5c372-let_the_alarm_to_be_used_as_wakeup_source as
uie_unsupported got dropped and we now set the bit directly.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Release Notes:
http://lists.busybox.net/pipermail/busybox-cvs/2023-May/041510.html
Refresh commands, run after busybox is first built once (nothing changed
compared to 1.36.0):
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-mipsel_24kc_musl/busybox-default/busybox-1.36.1
cd ..
./convert_defaults.pl ../../../build_dir/target-mipsel_24kc_musl/busybox-default/busybox-1.36.1/.config > Config-defaults.in
Manual edits needed afterward:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Instead of referring to a redundant job and ENV variables, rework build
workflow to accept and require split target and subtarget and use them
directly from inputs.
Rework each user and pass a JSON of tuple to matrix include with each
target/subtarget combination to test. Special notice this doesn't use
the github actions matrix combination feature but reference each
specific tuple of target and subtarget to test.
Just a cleanup no behaviour change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use buildbot user on git diff check instead of using git config
safe directory.
This should accomplish the same result but should be a better approach
following safe practice enforced by git.
Fixes: a7747e8670 ("ci: fix check kernel patches job")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch enables NVMEM u-boot-env driver (COFNIG_NVMEM_U_BOOT_ENV) on
generic subtarget to use from devices, for MAC address and etc.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
read_page() need to return maximum number of bitflips instead of the
accumulated number. Change takes from upstream mt7621 u-boot [1].
* @read_page: function to read a page according to the ECC generator
* requirements; returns maximum number of bitflips
* corrected in any single ECC step, -EIO hw error
[1] https://lore.kernel.org/all/cover.1653015383.git.weijie.gao@mediatek.com/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The x86_64 UML target wants to include SSSE3 optimized
crypto code which lives under /arch/x86/crypto.
However, these are not built and this causes an error.
| ERROR: module '[...]/arch/x86/crypto/sha512-ssse3.ko' is missing.
| make[3]: *** [modules/crypto.mk:990: [...]/kmod-crypto-sha512_5.15.112-1_x86_64.ipk] Error 1
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the UML build fails during the kernel build:
| arch/um/drivers/net_kern.c: In function 'compute_hash':
| arch/um/drivers/net_kern.c:322:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
| 322 | }
| | ^
|cc1: all warnings being treated as errors
The compute_hash() function is added by our patch:
102-pseudo-random-mac.patch
Instead of allocating a 1024 byte buffer on the stack for the SHA1
digest input, let's allocate the data on the heap. We should be
able to do that since crypto_alloc_ahash and ahash_request_alloc
also need to allocate structures on the heap.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
That was a workaround for OpenWrt generation of config files. This patch
was used to postpone returning from probe function until loading
firmware and calling register_wiphy().
All of that is not needed anymore thanks to the ieee80211 hotplug.d
script introduced in the commit 5f8f8a3661 ("base-files, mac80211,
broadcom-wl: wifi detection and configuration"). That takes care of
generating /etc/config/wireless entries even if wireless device appears
late in the booting process.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit 3b68fb57c9.
After refactoring build checks to update old symlinks,
and after a long time of no python 2 support,
this is no longer needed.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This makes the prereq stage update the symlinks
installed into staging_dir/host/bin
by rearrainging the way they are verified.
Before, seeing or installing a symlink would result in
a successful exit code, and not installing a symlink
would result is a failed exit code. However,
that is not able to account for the difference
between existing good and bad links, or whether
the link would be the same if it was reinstalled,
because the check can match the program to a different path.
Instead, let a success exit code represent
identifying an existing symlink as exactly the same
as what would be installed if it did not exist,
and let a fail exit code represent
needing to install the symlink
or not having a match to the check criteria.
The failing exit code is caught by a new second attempt
for all of the check-* targets which will then indicate
to the user that there was an update by having a success
exit code when the check is run again and the link is the same.
When there is nothing to update, the checks will run only once.
This relies on the ls command to be POSIX-conformant with long format:
"path/to/link -> target/of/link"
Also, make sure the symlink is executable, not just a file,
and the directory only needs to be created once.
Fixes: #12610
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Commit 54070a1 was added to allow building proper SDKs with kernels <
5.10. Now that all targets use at least kernel 5.10 it can be reverted.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
IGD is only useful when accelerating a VM guest that wants to direct
render to memory in the host's framebuffer, but since OpenWrt
typically runs on headless hardware, this serves no purpose.
Also build vfio with VFIO_NOIOMMU undefined (to get all of the code
enabled), but allow it to be enabled via boot-time modparams
settings (or at run-time via sysfs writes to
"/sys/module/vfio/parameters/enable_unsafe_noiommu_mode".
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
The PHY name has been changed to "mt7530-0" since IRQ support
was added to MT7530 driver.
Fixes: f9cfe7af1f ("kernel: backport MT7530 IRQ support")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(node names, added color, function+function-enumerator properties)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
adds ForceCommand option. If the command is specified,
it forces users to execute the command when they log in.
Signed-off-by: Nozomi Miyamori <inspc43313@yahoo.co.jp>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Sophos SG/XG-135 revision 3 has odd numbering of eth ports
where the WAN port (as marked on the case) is:
`eth6` and `eth0`, `eth1`, `eth2`, `eth3`, `eth5`, `eth7`, `eth8` are LAN ports.
Port `eth4` seems to be the SFP port.
Also add the missing LED definition for supported Sophos devices.
Original discussion at:
https://forum.openwrt.org/t/openwrt-on-revision-3-of-sophos-desktop-appliances/152912
Signed-off-by: Stan Grishin <stangri@melmac.ca>
A missing '\' caused the remaining parameters not to be passed to make.
This fixes the following error:
| gcc -c [...] fiptool.c -o fiptool.o
| In file included from fiptool.h:16,
| from fiptool.c:19:
|fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
| 19 | # include <openssl/sha.h>
| | ^~~~~~~~~~~~~~~
|compilation terminated.
|make[3]: *** [Makefile:58: fiptool.o] Error 1
as the HOST_CFLAGS are no longer passed.
then, HOST_CFLAGS is specified as a command argument, this
is a specific problem of our built since appending these
needs the override directive.
Fixes: df28bfe03247 ("tfa-layerscape: Change to github and use the latest tag")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Some U-Boot checks for a specified uImage time and refuses to boot if
mismatched. This patch fixes it by recognizing UIMAGE_TIME parameter.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1200Mhz
- Flash size: 32 MiB
- RAM: 512MB
- LAN: 2x 1Gbit/s
- 3x USB 2.0
Notes:
- The blue drive LED is triggered by HDD activity, it can not be controlled
via GPIO.
- The LCD screen requires proprietary code and does not function at this time.
- Due to a kernel-related issue with the Marvell 88SE6121 SATA controller,
currently only trays numbered #3 and #4 work, #1 and #2 do not. [1]
Serial pinout:
CN4
--------------
| 10 8 6 4 2 |
| 9 7 5 3 1 |
-------------- PIN 1 Mark (fat line)
1 = RXD
4 = TXD
6 = GND
9 = 3.3V (not necessary to connect)
Installation instructions:
1. download initramfs-uImage and copy into tftp server
2. connect the tftp server to network port #1
3. access uboot environment with serial cable and run
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x00800000 [initramfs-uImage filename]
bootm 0x00800000
4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash
[1] https://bugzilla.kernel.org/show_bug.cgi?id=216094
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
(aligned FROM from signed-off. LED+key rename, whitespace removal)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This removes unneeded kernel version switches from the targets after
kernel 5.10 has been dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
