Commit Graph

1599 Commits

Author SHA1 Message Date
Yuan Tao
649e098ec0 tools/libressl: update to 3.2.1
libressl update to 3.2.1
Delete 001-dont-build-tests-man.patch
Add configure args :
--enable-static
--disable-tests

The patch (001-dont-build-tests-man.patch) no longer works with the current version.
Follow the patch notes:
Adding the --enable-static and --disable-tests parameters should replace the patch.

Signed-off-by: Yuan Tao <ty@wevs.org>
2020-09-18 20:08:51 +02:00
Adrian Schmutzler
0b1cdb7eea treewide: remove empty default cases
There is no apparent reason to have an empty default case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 12:46:19 +02:00
Sander Vanheule
c9f51a9ad6 ath79: support for TP-Link EAP225-Wall v2
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.

The device was kindly provided for porting by Stijn Segers.

Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
  * Eth0 (back): 802.3af/at PoE in
  * Eth1, Eth2 (bottom)
  * Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
  * LED button, implemented as KEY_BRIGHTNESS_TOGGLE
  * Reset button

Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface

Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
      Do NOT bridge R164
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
    br0       Link encap:Ethernet  HWaddr 50:...:04
    eth0      Link encap:Ethernet  HWaddr 50:...:04
    wifi0     Link encap:UNSPEC  HWaddr 50-...-04-...
    wifi1     Link encap:UNSPEC  HWaddr 50-...-05-...

Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 19:37:24 +02:00
Sander Vanheule
9dd4ba3d7e ath79: add support for TP-Link EAP245-v3
TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.

Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)

Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface

The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.

Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.

Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt

Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
    ath0      Link encap:Ethernet  HWaddr 74:..:E2
    ath10     Link encap:Ethernet  HWaddr 74:..:E3
    br0       Link encap:Ethernet  HWaddr 74:..:E2
    eth0      Link encap:Ethernet  HWaddr 74:..:E2

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-09-09 20:42:10 +03:00
Sander Vanheule
14464e1128 firmware-utils/tplink-safeloader: add compat level
TP-Link has introduced a compatibility level to prevent certain
downgrades. This information is stored in the soft-version partition,
changing the data length from 0xc to 0x10.

The compatibility level doesn't change frequently. For example, it has
the following values for the EAP245v3 (released 2018-Q4):
* FW v2.2.0  (2019-05-30): compat_level=0
* FW v2.3.0  (2019-07-31): compat_level=0
* FW v2.3.1  (2019-10-29): compat_level=1
* FW v2.20.0 (2020-04-23): compat_level=1

Empty flash values (0xffffffff) are interpreted as compat_level=0.
If a firmware upgrade file has a soft-version block without
compatibility level (data length < 0x10), this is also interpreted as
compat_level=0.

By including a high enough compatibility level in factory images, stock
firmware can be convinced to accept the image. A compatibility level
aware firmware will keep the original value.

Example upgrade log of TP-Link EAP245v3 FWv2.3.0 to FWv2.20.0:
    [NM_Debug](nm_fwup_verifyFwupFile) 02073: curSoftVer:2.3.0 Build
        20190731 Rel. 51932,newSoftVer:2.20.0 Build 20200423 Rel. 36779
    ...
    AddiHardwareVer check: NEW(0x1) >= CUR(0x0), Success.
    ...
    [NM_NOTICE](updateDataToNvram) 00575: Restore old additionalHardVer:
    0x0.(new 0x1)
    [NM_NOTICE](updateDataToNvram) 00607: PTN 07: name = soft-version,
        base = 0x00092000, size = 0x00000100 Bytes, upDataType = 1,
        upDataStart = 7690604b, upDataLen = 00000018
    [NM_Debug](updateDataToNvram) 00738: PTN 07: write bytes = 000002eb

Other firmware upgrades have been observed to modify the compabitility
stored level (e.g. TP-Link EAP225-Outdoor FWv1.4.1 to FWv1.7.0).
Therefore, it seems to be the safest option to set the OpenWrt
compatibility level to the highest known value instead of the highest
possible value (0xfffffffe), to ensure users do not get unexpectedly
refused firmware upgrades when using a device reverted back to stock.

To remain compatible with existing devices and not produce different
images, the image builder doesn't store a compatibility level if it is
zero.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-09-09 20:41:50 +03:00
Sander Vanheule
6985a26e59 firmware-utils/tplink-safeloader: soft-version magic is data length
The soft-version partition actually contains a header and trailing data:
* header: {data length, [zero]}
* data: {version, bcd encoded date, revision}

The data length is currently treated as a magic number, but should
contain the length of the partition data.

This header is also present the following partitions (non-exhaustive):
* string-based soft-version
* support-list

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-09-09 20:41:50 +03:00
Jo-Philipp Wich
6485f521c9 tools: fakeroot: use TCP as IPC transport
Some environments, e.g. first gen WSL, do not support SysV IPC.
Enforce the use of TCP transport instead which should be universally
available.

Fixes: FS#3317
Ref: https://github.com/microsoft/WSL/issues/4067
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-09-09 13:33:50 +02:00
Daniel Golle
97096531bb fakeroot: add license information
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-09-08 15:02:52 +01:00
Adrian Schmutzler
94198e2a1c rb532: drop target
This target is still on kernel 4.14, and recent attempts to move it to
kernel 5.4 have not led to success. The device tester reported that it
wouldn't boot with the following messages:

From sysupgrade:

  Press any key within 4 seconds to enter setup....
  loading kernel from nand... OK
  setting up elf image... OK
  jumping to kernel code

At this point the system hangs.

From CompactFlash:

  Press any key within 4 seconds to enter setup....
  Booting CF
  Loading kernel... done
  setting up elf image... kernel out of range kernel loading failed

The tester reported that the same was observed with current master
(kernel 4.14) as well. This looks like some kernel size restriction.

Since this target is quite old and only supports one device, and since
nobody else seemed interested in working on this for quite some time,
I decided to not put further work into analyzing the problem and drop
this together with the other 4.14-only targets.

Patchwork series:
https://patchwork.ozlabs.org/project/openwrt/list/?series=197066&state=*

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Adrian Schmutzler
edb5d2a320 tools: sort alphabetically
This sorts the added tools and builddir dependencies alphabetically
to make it easier to find something in the Makefile.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Adrian Schmutzler
48905af01d tools: drop unused upslug2 and wrt350nv2-builder
These tools have been used by the orion target which has been
removed in Jan 2020 [1].

Both were specifically meant for the WRT350Nv2, which is not
supported anymore.

So, let's remove them as well.

[1] 89f2deb372 ("orion: remove unmaintained target")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Felix Fietkau
7f0cb91d71 tools/squashfskit4: fix build on non-linux systems
The xattr related function calls are linux specific

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-01 17:01:56 +02:00
Paul Spooren
35f2116519 treewide: https for downloads.openwrt.org sources
Instead of using http and https for source downloads from
downloads.openwrt.org, always use https for it's better security.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-31 11:26:10 +01:00
Thomas Petazzoni
d3d40cd6a4 tools/squashfskit4: add xattr support to mksquashfs for SELinux
SELinux uses extended attributes to store SELinux security contexts.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase, add commit message]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
2020-08-31 01:15:41 +01:00
David Bauer
1aa71833fe tools: add back lzma-old for ath79
lzma-old host package is required for building ath79 images, as
mksquashfs-lzma is required for generating netgear images.

Fixes commit 4e4ee46495 ("ar71xx: drop target")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-08-31 00:21:18 +02:00
Hannu Nyman
040b625c4b tools/coreutils: update to 8.32
Update coreutils to version 8.32.
Remove upstreamed patch.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-30 22:21:34 +02:00
Adrian Schmutzler
d7fb7ac278 ath79: increase kernel partition for ar9344 TP-Link CPE/WBS
The kernel has become too big again for the ar9344-based TP-Link
CPE/WBS devices which still have no firmware-partition splitter.

Current buildbots produce a kernel size of about 2469 kiB, while
the partition is only 2048 kiB (0x200000). Therefore, increase it
to 0x300000 to provide enough room for this and, hopefully, the
next kernel.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 22:20:37 +02:00
Adrian Schmutzler
4e4ee46495 ar71xx: drop target
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.

This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 22:18:35 +02:00
Hannu Nyman
395c848d16 tools/mpc: update to 1.2.0
Update mpc to version 1.2.0.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-27 21:18:16 +02:00
Hauke Mehrtens
561031921f tools: mtd-utils: Update to version 2.1.2
The release notes says this:
As already said, the changes since 2.1.1 are primarily bug fixes, addressing
compiler warnings and issues reported by diagnostic tools, but also build
failures for some configurations.
https://lists.infradead.org/pipermail/linux-mtd/2020-July/081299.html

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-26 23:29:35 +02:00
Hannu Nyman
d622cf81af tools/ccache: update to 3.7.11
Update ccache to 3.7.11

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-23 19:40:51 +02:00
Hannu Nyman
84834df9b9 tools/cmake: update to 3.18.2
Update cmake to version 3.18.2.
Refresh patches.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-23 19:40:42 +02:00
Hannu Nyman
4faf7704a2 tools/mpfr: update to 4.1.0
Update mpfr to version 4.1.0.
Refresh patches.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-23 19:40:32 +02:00
Hannu Nyman
1cf842dd13 tools/bison: update to 3.7.1
Update GNU bison to version 3.7.1.
Refresh patches.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-23 11:29:24 +02:00
Alexander Couzens
6d5d815e3f
tools/tplink-safeloader: use soft_ver 1.9.1 for archer c6 v2
TP-LINK published a firmware update for the archer c6 v2.
This updates also reached the factory devices. Newer software version
rejects downgrading to 1.2.x. Use 1.9.x to allow installing the factory images
and have a little bit time to change it again.

Tested on archer c6 v2 with firmware 1.3.1

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-08-19 19:21:24 +02:00
Felix Fietkau
a36965347e tools/coreutils: install ln
It is needed for libsepol on non-GNU systems

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-13 20:08:29 +02:00
Andreas Böhler
ab74def0db ath79: add support for TP-Link TL-WPA8630P v2
The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC
and 2.4GHz and 5GHz WiFi modules.

Specifications
--------------

  - QCA9563 750MHz, 2.4GHz WiFi
  - QCA9888 5GHz WiFi
  - 8MiB SPI Flash
  - 128MiB RAM
  - 3 GBit Ports (QCA8337)
  - PLC (QCA7550)

MAC address assignment
----------------------

WiFi 2.4GHz and LAN share the same MAC address as printed on the label.
5GHz WiFi uses LAN-1, based on assumptions from similar devices.

LAN Port assignment
-------------------

While there are 3 physical LAN ports on the device, there will be 4
visible ports in OpenWrt. The fourth port (internal port 5) is used
by the PowerLine Communication SoC and thus treated like a regular
LAN port.

Versions
--------

Note that both TL-WPA8630 and TL-WPA8630P, as well as the different
country-versions, differ in partitioning, and therefore shouldn't be
cross-flashed.

This adds support for the two known partitioning variants of the
TL-WPA8630P, where the variants can be safely distinguished via the
tplink-safeloader SupportList. For the non-P variants (TL-WPA8630),
at least two additional partitioning schemes exist, and the same
SupportList entry can have different partitioning.
Thus, we don't support those officially (yet).

Also note that the P version for Germany (DE) requires the international
image version, but is properly protected by SupportList.

In any case, please check the OpenWrt Wiki pages for the device
before flashing anything!

Installation
------------

Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.

Additional thanks to Jon Davies and Joe Mullally for bringing
order into the partitioning mess.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[minor DTS adjustments, add label-mac-device, drop chosen, move
common partitions to DTSI, rename de to int, add AU support strings,
adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk,
adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 11:48:08 +02:00
Thomas Petazzoni
9e7ef46065 tools: add fakeroot
SELinux support requires setting the appropriate SELinux security context
to files and directories, which needs to happen at build time in order
to support read-only root filesystem scenarios. In order to create these
security contexts, we will have to run some SELinux-specific tools on
the host machine, but that requires root access. This adds support for
fakeroot, which the build process will use to run the SELinux security
context creation and the image creation.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>

Apply to current master, and adjust commit message

Thomas' original work is available at
http://lists.infradead.org/pipermail/openwrt-devel/2019-November/025976.html.

Signed-off-by: W. Michael Petullo <mike@flyn.org>
[add rules.mk FAKEROOT variable]
Signed-off-by: Paul Spooren <mail@aparcar.org>
[update, fix macos build]
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-10 10:09:55 +02:00
Piotr Stefaniak
e27fbae63c tools/cmake: fix typo in parallel make patch
The variable in the case argument was mistyped, so the case always
checked against an empty string and never matched.

Fix the variable name. Add a PKG_RELEASE to Makefile so we can bump it.

Fixes: d6de31310c ("cmake: restore parallel build support for bootstrap")

Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
[add commit message, add PKG_RELEASE, fix commit title, add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 00:01:51 +02:00
Adrian Schmutzler
c25c9e98f5 Revert "build: fix typo in cmake patch"
This reverts commit 685570858d.

The commit had several formal flaws, revert it and hopefully apply
it properly next time.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-09 23:59:20 +02:00
Piotr Stefaniak
685570858d build: fix typo in cmake patch
The variable in the case argument was mistyped, so the case always
checked against an empty string and never matched.

Fix the variable name.

Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
[add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-09 23:57:17 +02:00
Sander Vanheule
34271d38ae tools/firmware-utils: use UTC for image timestamps
By using localtime() to determine the timestamp that goes into factory
images, the resulting image depends on the timezone of the build system.
Use gmtime() instead, which results in more reproducible images.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-08-07 09:48:33 +02:00
Richard Fröhning
009e62c92c ramips: add support for TP-Link RE200 v3
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button

Unverified:
- UART header on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 23:34:34 +02:00
Adrian Schmutzler
1deaf695ec ramips: fix/tidy up 4M tplink-v2-image flash layouts
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:

device         uboot    OEM firmware  OpenWrt (incl. config)
tl-wr840n-v5   0x20000  0x3c0000      0x3d0000
tl-wr841n-v14  0x10000  0x3d0000      0x3e0000

In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.

However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.

So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 12:17:08 +02:00
Ted Hess
600416d5c1 tools/mkimage: create .itb file with read-access for group,other not just owner.
This patch will fix the source of 403 errors on these files
from downloads.openwrt.org.

Signed-off-by: Ted Hess <thess@kitschensync.net>
2020-07-23 14:25:10 -04:00
Paul Spooren
fca3bf4f4c tools/flock: add PKG_{VERSION,RELEASE}
The stored source code of flock contains the version string of version
2.18, reflect that in the Makefile.

Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-07-23 11:30:22 +02:00
Paul Spooren
d2332e215e tools/sstrip: add PKG_{VERSION,RELEASE}
Comparing the in tree stored source file of sstrip suggests it's version
2.0[0], reflect that in the Makefile.

Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.

[0]: df4426a0f0 (diff-d3ba694d91432a068d5d3b36abf8cd0f)

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-07-23 11:30:14 +02:00
Paul Spooren
7c12d5d167 tools/firmware-utils: add PKG_RELEASE
There is no versioning information in the firmware-utils code nor the
Makefile. Consider it as first release by adding PKG_RELEASE.

Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.

Also update copyright.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-07-23 11:30:09 +02:00
Paul Spooren
d32012376a tools/patch-image: add PKG_RELEASE
There is no versioning information in the patch-image code nor the
Makefile. Consider it as first release by adding PKG_RELEASE.

Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.

Also update copyright.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-07-23 11:30:04 +02:00
Adrian Schmutzler
240793d175 tools: drop PKG_VERSION for purely local packages
This applies to tools directory what has been done for package/ in
commit 9c170cb92f ("package: drop PKG_VERSION for purely local
packages"):

In the package guidelines, PKG_VERSION is supposed to be used as
"The upstream version number that we're downloading", while
PKG_RELEASE is referred to as "The version of this package Makefile".
Thus, the variables in a strict interpretation provide a clear
distinction between "their" (upstream) version in PKG_VERSION and
"our" (local OpenWrt trunk) version in PKG_RELEASE.

For local (OpenWrt-only) packages, this implies that those will only
need PKG_RELEASE defined, while PKG_VERSION does not apply following
a strict interpretation. While the majority of "our" packages actually
follow that scheme, there are also some that mix both variables or
have one of them defined but keep them at "1".

This is misleading and confusing, which can be observed by the fact
that there typically either one of the variables is never bumped or
the choice of the variable to increase depends on the person doing the
change.

Consequently, this patch aims at clarifying the situation by
consistently using only PKG_RELEASE for "our" packages. For tools/,
only three packages were affected. This fixes two of them, and
leaves the remaining wrt350nv2-builder untouched, as the code there
seems to have some versioning of its own that is treated as upstream
version in PKG_VERSION.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-23 10:54:33 +02:00
Adrian Schmutzler
4a2380a1e7 tplink-safeloader: expand support list for TP-Link CPE210 v3
This adds new strings to the support list for the TP-Link CPE210 v3
that are supposed to work with the existing setup.

Without it, the factory image won't be accepted by the vendor UI on
these newer revisions.

Tested on a CPE210 v3.20 (EU).

Ref: https://forum.openwrt.org/t/build-for-cpe210-v3-20/68000

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-20 13:43:36 +02:00
Petr Štetiar
61b36ee9ba firmware-utils: mkfwimage: fix memcpy and strncpy usage
Firmware is binary blob, so there are barely any NULL terminated strings
expected, so we should probably convert all chars into u8 types, and
after that it's clear, that using strcpy doesn't make sense anymore.

This is rather theoretical stuff, but `uint8_t name[PART_NAME_LENGTH]`
means, that you can supply PART_NAME_LENGTH sized name, not
PART_NAME_LENGTH-1 name when NULL terminated.

Ref: https://github.com/openwrt/openwrt/pull/2274
Fixes: 04cb651376 ("firmware-utils: mkfwimage: fix more errors reported by gcc-6/7/9")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 13:33:28 +02:00
David Woodhouse
dca867c5a3 firmware-utils/ptgen: allow explicit placement of partitions
For Banana Pi R2 we need to place the U-Boot partition at precisely 0x50000.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
Andrea Dalla Costa
d64b20da21 firmware-utils/hcsmakeimage: fix possible memory leak and resource leaks
Add missing calls to `free` for variable `filebuffer`.
Add missing calls to `fclose` for variables `fd` and `fd_out`.

Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
2020-07-08 16:07:05 +02:00
Christoph Krapp
ba0f4f0cfd ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.

TFTP recovery to stock firmware:

Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 00:40:04 +02:00
Rowan Border
33fae8421e ramips: add support for TP-Link RE220 v2
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.

Specifications

MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.

Web Interface Installation

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Signed-off-by: Rowan Border <rowanjborder@gmail.com>
2020-06-30 17:23:32 +02:00
Sungbo Eo
7da3c3b491 firmware-utils: sort tools alphabetically
Also remove leading whitespace after comma.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-06-28 02:27:36 +02:00
Andrew Cameron
d93da0d016 ath79: add support for TP-Link CPE610 v2
TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps Ethernet
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 23dBi high-gain directional 2×2 MIMO antenna and a
   dedicated metal reflector
 - Power, LAN, WLAN5G green LEDs
 - 3x green RSSI LEDs

Flashing instructions:
 Flash factory image through stock firmware WEB UI
 or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2020-06-20 13:03:39 +02:00
Joseph C. Lehner
0a73c61cb9 mkchkimg: use higher version code
This patch changes the version code of the image header
from `1.1.99_0.0.0.0` to `99.99.99_99.99.99.99`. This
is neccessary on some devices where the stock firmware
checks the version field, possibly preventing third-party
firmware from being installed.

Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2020-06-09 16:59:33 +02:00
Andreas Wiese
c764c512ac ath79: add support for TP-Link RE450 v3
TP-Link RE450 v3 is a dual band router/range-extender based on
Qualcomm/Atheros QCA9563 + QCA9880.

This device is nearly identical to RE450 v2 besides a modified flash
layout (hence I think force-flashing a RE450v2 image will lead to at
least loss of MAC address).

Specification:

- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button-
- possible UART header on PCB¹

Flash instruction:
Apply factory image in OEM firmware web-gui.

¹ Didn't check to connect as I didn't even manage to connect on
  RE450v2 (AFAIU it requires disconnecting some resistors, which I was
  too much of a coward to do).  But given the similarities to v2 I
  think it's the same or very similar procedure (and most likely also
  the only way to debrick).

Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net>
[remove dts-v1 and compatible in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Matthias Schiffer
258dc0d0fd
tools: add zstd
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2020-05-31 11:03:30 +02:00
DENG Qingfang
48e3449945 ccache: update to 3.7.9
Update ccache to 3.7.9

Release notes:
https://ccache.dev/releasenotes.html#_ccache_3_7_9

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-05-28 21:22:18 +02:00
Hauke Mehrtens
1bbc1aa884 squashfs: Fix compile with GCC 10
Fixes the following build error with GCC 10:
	/usr/bin/ld: read_fs.o:(.bss+0x0): multiple definition of `swap'; mksquashfs.o:(.bss+0x1b2a88): first defined here
And a compile warning.

Fixes: FS#3104, FS#3119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-05-24 14:38:40 +02:00
Karel Kočí
3c1d1d4332 tools: add autoconf-archive
Some autotools based build systems are using autoconf-archive scripts
and are expecting them to almost always be available. This is not
required for regular releases as tar balls generated for releases
commonly have existing configure script. This is rather intended to be
used with autotools.mk's autoreconf and in cases it is not always
possible to get release tar ball.

Including this adds little to no overhead in terms of build time as
those are just m4 scripts copied to an appropriate location.

Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[fixed From: to match SoB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-20 15:37:16 +02:00
Roger Pueyo Centelles
0486641849 firmware-utils: mkfwimage: add support for Ubiquiti XC devices
This commit adds support for Ubiquiti devices based on the XC board
type, such as the PowerBeam 5AC 500. The factory binary structure is
the same as the WA type.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-05-17 21:03:19 +02:00
Lucian Cristian
042917f1c4 tools/mkimage: update to 2020.04
also change the download source to https and add a mirror
drop merged patches

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[Add extra changes to compile on FreeBSD, merge two patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-04-26 21:20:47 +02:00
Kevin Darbyshire-Bryant
1e3d3d2bd5 tools/e2fsprogs: fix build under macos
macos doesn't define a loff_t type, the native off_t type being 64bit
anyway.

Persuade e2fsprogs to accept off_t instead on macos

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-10 11:52:00 +01:00
Daniel Engberg
5d7812495b tools/mm-macros: Update to 1.0.0
Update mm-macros to 1.0.0

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-04-09 22:09:21 +02:00
Daniel Engberg
d158b26c1e tools/xz: Update to 5.2.5
Update xz to 5.2.5
Disable NLS support to be consistent with other tools such as bison, e2fsprogs
and sed.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-04-09 22:09:13 +02:00
Daniel Engberg
169afa9fe4 tools/mtools: Update to 4.0.24
Update mtools to 4.0.24

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-04-09 22:09:04 +02:00
Daniel Engberg
71ea940a84 tools/findutils: Update to 4.7.0
Update findutils to 4.7.0
Remove patches
Enable pthreads
Disable NLS support to be consistent with other tools such as bison, e2fsprogs
and sed.
Disable selinux support to be consistent with other tools such as sed and tar
Disable rpath as we don't need hardcoded paths

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-04-09 22:08:38 +02:00
Daniel Engberg
c9daacbf18 tools/e2fsprogs: Update to 1.45.6
Update e2fsprogs to 1.45.6

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-04-09 22:08:29 +02:00
Rosen Penev
8af80e79bd tools/cmake: update to 3.17.0
Remove libressl patches; they are no longer needed as LibreSSl adde
support

Replace qt tests patch with one that disables all of them.

Refresh remaining one.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-04-06 20:30:18 +02:00
李国
1963bbaa8f firmware-utils: ptgen: add GPT support
Add GPT support to ptgen, so we can generate EFI bootable images.

Introduced two options:
    -g        generate GPT partition table
    -G GUID   use GUID for disk and increase last bit for all partitions

We drop The alternate partition table to reduce size, This may cause
problems when generate vmdk images or vdi images. We have to pad enough
sectors when generate these images.

Signed-off-by: 李国 <uxgood.org@gmail.com>
[fixed compilation on macOS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-31 16:20:47 +02:00
Georgi Vlaev
ff75bbc423 tplink-safeloader: update soft_ver for TP-Link Archer C6 v2 (EU)
The last couple of TP-Link firmware releases for Archer C6 v2 (EU)
have switched to version 1.2.x. Bump the soft_ver to "1.2.1" to
allow firmware updates from the vendor web interface.

TP-Link vendor firmware releases supported by this change:
* Archer C6(EU)_V2_200110: soft_ver:1.2.1 Build 20200110 rel.60119
* Archer C6(EU)_V2_191014: soft_ver:1.2.0 Build 20191014 rel.33289

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
2020-03-30 01:46:50 +02:00
Robert Marko
be4ed1db18
tools: squashfskit4: fix build with GCC10
In order to build squashfskit with GCC10, this backport from upstream is needed.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[increase PKG_RELEASE]
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-03-22 02:06:16 +01:00
Alexander Couzens
1f4020a293 squashfskit4/Makefile: introduce PKG_RELEASE=1
When adding patches, the PKG_RELEASE should be increased.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-03-22 02:05:41 +01:00
Adrian Schmutzler
646d95c374 ath79: add support for TP-Link Archer C60 v3
TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.

It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
   directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server
8. Wait ~30 second to complete recovery

While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".

In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:

name           device            firmware
factory-boot   0x00000-0x1fb00   0x00000-0x1fa00
default-mac    0x1fb00-0x1fd00   0x1fa00-0x1fc00
pin            0x1fd00-0x1fe00   0x1fc00-0x1fd00
product-info   0x1fe00-0x1ff00   0x1fd00-0x1ff00
device-id      0x1ff00-0x20000   0x1ff00-0x20000

While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-18 13:49:06 +01:00
Jo-Philipp Wich
6de7406d54 pkgconf: always retain -I and -L flags
The pkgconf fork filters -I and -L flag values from .pc files which match
pkgconf's builtin system directory value.

During configure, pkgconf derives the default system include and library
search path values from exec_prefix, which is set to staging_dir/host in
the host tool build phase.

Due to that, pkgconf will drop all -I and -L flags pointing to
staging_dir/host/include or staging_dir/host/lib, unless invoked with
--keep-system-cflags and --keep-system-libs respectively, breaking our
kernel libelf discovery / stack validation workarounds.

In order to inhibit the filtering, add --keep-system-cflags and
--keep-system-libs to our pkg-config shell wrapper.

Fixes: GH#2832
Fixes: 867298cf47 ("tools/pkg-config: Replace with pkgconf")
Ref: https://lists.infradead.org/pipermail/openwrt-devel/2020-March/022182.html
Ref: https://git.openwrt.org/fe43969336201f2cc7d103b68fd6e65989bee184
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Petr Štetiar <ynezz@true.cz>
2020-03-15 20:32:10 +01:00
Kevin Darbyshire-Bryant
0a06fcf608 build: fix kernel 5.4 on macos
As part of the kernel build process there are utilities built to run on
the host system that expect linux kernel headers to be available.
Unfortunately macos/darwin doesn't have these headers.

vdso2c requires types.h so provide a minimal stub to satisfy it.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-03-14 13:20:06 +00:00
Yufei Miao
763de7bd51 tools/cmake: Update to 3.16.5
Update cmake to 3.16.5

Signed-off-by: Yufei Miao <myf@myf.cloud>
2020-03-12 21:31:17 +01:00
Michael T Farnworth
b468353a37 mkrasimage: fix segmentation fault
Code was attempting to determine the size of the file
before it was actually known and allocating insufficient
memory space.  Images above a certain size caused a
segmentation fault.  Moving the calloc() ensured ensured
that large images didn't result in a buffer overflow on
memcpy().

Signed-off-by: Michael T Farnworth <michael@turf.org>
[fixed name in From to match one in SoB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-01 21:36:00 +01:00
Rosen Penev
c60be19693 tools/pkgconf: Run pkg-config wrapper through shellcheck
Mainly quoting fixes.

Separated parameters by \ for easier readability.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-03-01 21:36:00 +01:00
Rosen Penev
867298cf47 tools/pkg-config: Replace with pkgconf
pkgconf is a newer, actively maintained implementation of pkg-config that
supports more aspects of the pkg-config file specification and provides a
library interface that applications can use to incorporate intelligent
handling of pkg-config files into themselves (such as build file
generators, IDEs, and compilers). Through its pkg-config compatibility
interface (activated when it is run as "pkg-config"), it also can
completely replace the original implementation.

It is also lighterweight and does not require glib2, as pkg-config does.

On other distros, pkgconf is symlinked to pkg-config. For simplicity here,
it is renamed to pkg-config.real, as in the original package.

Initial results have been positive. As before, pkgconf works as long as
the pkg-config files point to the proper paths.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[backported upstream fix for Meson]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-01 21:36:00 +01:00
Jeffery To
4a308bad82 tools: Fix "lib" symlink created inside $(STAGING_DIR_HOST)/lib
Currently, if "make tools/install" is called after tools have already
been installed, a symbolic link named "lib" will be created inside
$(STAGING_DIR_HOST)/lib, pointing to "lib" (i.e. itself).

During tools/prepare, a "lib64" symlink is created inside
$(STAGING_DIR_HOST) that points to "lib" (also inside
$(STAGING_DIR_HOST)).

If tools/prepare is called and the "lib64" symlink already exists, then
ln will treat it as a directory and instead create a symlink named "lib"
inside of that directory.

This adds the -n option for ln so that $(STAGING_DIR_HOST)/lib64 is
always treated as a normal file (the link name), not as a directory.

Signed-off-by: Jeffery To <jeffery.to@gmail.com>
2020-03-01 21:35:59 +01:00
Daniel Engberg
b0a3f1e8f4 tools/bison: Update to 3.5.1
Update bison to 3.5.1
Use POSIX threads as the previous option is no longer valid
Disable NLS support to be consistent with other tools such as e2fsprogs and sed

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-02-19 22:02:47 +01:00
Daniel Engberg
cf443e84f5 tools/e2fsprogs: Update to 1.45.5
Update e2fsprogs to 1.45.5
Enable pthreads support

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-02-18 21:48:49 +01:00
Daniel Engberg
477d1c540e tools/gmp: Remove obsolete options
Remove mpbsd argument

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-02-18 21:39:23 +01:00
Daniel Engberg
4b591c5e6b tools/sed: Update to 4.8
Update sed to 4.8
Use POSIX threads
Disable i18n and selinux support

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-02-18 21:39:14 +01:00
Daniel Engberg
82211e5f49 tools/patchelf: Update to 0.10
Update patchelf to 0.10

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-02-18 21:39:03 +01:00
Daniel Engberg
0ffb7b02ba tools/libressl: Update to 3.0.2
Update libressl to 3.0.2 and remove 010-avoid-glibc.patch as fix is added by upstream

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2020-02-18 21:38:51 +01:00
Dan Haab
9aa6569aa6 firmware-utils: add lxlfw tool for generating Luxul firmwares
It's a simple tool prepending image with a Luxul header.

Signed-off-by: Dan Haab <dan.haab@legrand.com>
2020-02-07 09:31:22 +01:00
Andreas Böhler
6d6f36ae78 ramips: add support for TP-Link RE200 v2
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G  : *:0F

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Serial console
--------------

Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

Additonal notes
---------------

It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-01 19:41:51 +01:00
Hannu Nyman
b77ce0c720 tools/gmp: update to 6.2.0
Update GNU gmp to version 6.2.0

Release notes:  https://gmplib.org/gmp6.2.html

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-01-25 22:07:32 +01:00
Adrian Schmutzler
b2102be8a5 ar71xx: use dynamic partitioning for TP-Link TL-WA850RE v2
This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and
will allow to use this for ath79 as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-22 23:52:51 +01:00
Hannu Nyman
96e9d48664 tools/bison: update to 3.5
Update bison to 3.5

Release notes:
https://lists.gnu.org/archive/html/info-gnu/2019-12/msg00002.html

Note for future: release notes mention that YYPRINT macro is
declared deprecated, but apparently still works for now. I found
one possible use of that in scripts/config/zconf.tab.c_shipped
That might be modernized at some point, but as the file is synced
with the one from upstream Linux, it might get fixed there.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-01-21 18:43:58 +01:00
Anderson Vulczak
7a8bfbf0ff tools: tplink-safeloader: update soft_ver for TP-Link Archer C6 v2 (EU)
This patch updates "soft_ver" for TP-Link Archer C6 v2 (EU).

It makes possible to upload OpenWrt on lastest vendor's firmware
as the web-based updater checks for major.minor version during upload.

Due to that on next major/minor version update TP-Link will stop
us from using the web-based firmware update tool, so it will
require a new patch on soft_ver to match major and minor version.
Up to today's latest stock firmware the patch (major.minor.patch)
version does not matters, that allows downgrade from 1.1.4 to 1.1.1
but do not allow downgrade from 1.1.X to 1.0.X.

Signed-off-by: Anderson Vulczak <andi@andi.com.br>
2020-01-19 00:19:39 +01:00
Steffen Förster
93a4c8afbf ramips: add support for TP-Link RE305 v1
Specification:

SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
  - 2.4GHz: MT7628AN
  - 5GHz: MT7612EN
LAN: 1x 10/100 Mbps

Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.

The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.

Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
2020-01-18 19:39:05 +01:00
Hannu Nyman
343f27f8b0 tools/cmake: update to 3.16.2
Update cmake to 3.16.2 and refresh patches.

Release notes:
https://cmake.org/cmake/help/v3.16/release/3.16.html

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-01-18 14:18:22 +01:00
DENG Qingfang
5355baf21f ccache: update to 3.7.7
Update ccache to 3.7.7

Release notes:
https://ccache.dev/releasenotes.html#_ccache_3_7_7

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-01-16 18:59:42 +01:00
Andrea Dalla Costa
3c77e4ae4d wrt350nv2-builder: Fix memory leak
Add missing call to `free` for variable `buffer` in function
`create_bin_file`.

Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
2020-01-14 17:48:50 +01:00
Andrea Dalla Costa
8057970d2a firmware-utils/mktitanimg: fix possible resource leak
Add missing call to `fclose` for file pointer `nsp_image`.

Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
2020-01-14 17:48:50 +01:00
Andrea Dalla Costa
1775f690d5 firmware-utils/mksenaofw: fix possible memory leak
Add missing calls to `free` for variable `pmodel`.

Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
2020-01-14 17:48:50 +01:00
Andrea Dalla Costa
b886d3c8f3 firmware-utils/mkfwimage: fix possible memory and resource leak
Add missing calls to `free` for variable `mem`.
Add missing call to `fclose` for variable `f`.

The same changes were made in both `mkfwimage.c` and `mkfwimage2.c`.

Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
2020-01-14 17:48:50 +01:00
Andrea Dalla Costa
8e3b3152e5 firmware-utils/mkchkimg: fix possible resource leaks
Add missing `fclose` calls for file pointers `kern_fp`, `fs_fp`
and `out_fp`.
Not closing files could lead to resource leaks.

Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
2020-01-14 17:48:50 +01:00
Andrea Dalla Costa
0ae0f48cec firmware-utils: fix possible memory leak and resource leak
Add missing calls to `free` for variable `buffer`.
This could lead to a memory leak.

Add missing call to `close` for file pointer `fdin`.
This could lead to a resource leak.

Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
2020-01-14 17:48:50 +01:00
Andrea Dalla Costa
402b362db4 firmware-utils/dgfirmare: fix possible resource leak
Add missing calls to `fclose` in functions `write_img`, `write_rootfs`
and `write_kernel`.
The not-closed files could lead to resource leaks.

Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
2020-01-14 17:48:50 +01:00
Tobias Schramm
d29929be07 firmware-utils: mkfwimage: add support for Ubiquiti SW devices
This commit adds support for Ubiquiti ToughSwitch XP (and probably also
EdgeSwitch XP) devices. They are mostly based on the same hardware as
MX devices.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2020-01-12 14:12:50 +01:00
Hauke Mehrtens
271d0c825b make_ext4fs: Update to version 2020-01-05
5c201be Add LDFLAGS when building libsparse.a
ec17045 make_ext4fs: fix build on musl systems

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-01-05 20:04:37 +01:00
Andreas Böhler
a3010a7f8d ramips: add support for TP-Link RE200 v1
TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN.

Specifications
--------------

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled; only 6 supported), 2x button

There are 2.4G and 5G LEDs in red and green which are controlled
separately. The 5G LED is currently not supported, since the GPIOs couldn't
be determined.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.

Serial console
--------------

Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console. Since the web upgrade overwrites
the boot loader, you might also brick your device.

Additional notes
----------------

MAC address assignment is based on stock-firmware. For me, the device
assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G
WiFi has a separate MAC with +2.

*:88    Ethernet/2.4G    label, uboot 0x1fc00, userconfig 0x0158
*:89    unused           userconfig 0x0160
*:8A    5G               not present in flash

This seems to be the first ramips device with a TP-Link v1 header. The
original firmware has the string "EU" embedded, there might be some region-
checking going on during the firmware upgrade process. The original
firmware also contains U-Boot and thus overwrites the boot loader during
upgrade.
In order to flash back to stock, the first header and U-Boot need to be
stripped from the original firmware.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2019-12-31 13:23:55 +01:00